Let's use that - it's better than gitter ever was, and it's all on one site.
2.5.0 is here! New Wire library is in! Serial improvements are in! (Including some snazzy things like loopback support)
Try it out! Report issues! Build awesome stuff!
Well, I screwed up fairly badly in handling the board manager json. The short version of the story is that I discovered a bug in 2.4.3 that required no changes to the core, just a board manager change. So I changed the json file (big mistake). Anyone who installed after that change would get a java null pointer exception when trying to upgrade. But I didn't realize this until I had already done a release in 2.5.x, then realized I'd missed that fix, and modified the board manager json after release. Then I finally made the connection between having done that and the flood of support inquiries relating to being unable to upgrade.
If you are impacted by this, exit all instances of the IDE, delete all folders within your Arduino15 folder (reinstalling the Arduino IDE won't fix the error - arduino15 is located in some other location depending on your operating system; on windows it's C:/Users/(your username)/AppData/Local/Arduino15 - note that AppData is hidden). Deleting the folders within Arduino15 instead of the whole Arduino15 folder will allow you to keep your saved preferences file, while getting rid of any trace of the mess that my defective board manager json made of your packages.
Sorry about that. I've put in place measures to ensure I dont make such a collossal screwup again. That's what I deserve for trying to keep updates flowing while preoccupied by a chaotic relocation.
An Arduino core for the tinyAVR 0-series, 1-series, and now the 2-series. These parts have an improved architecture compared to the "classic" tinyAVR parts (which are supported by ATTinyCore), with improved peripherals and improved execution time for certain instructions (these are similar in both regards to the advanced AVR Dx-series, as well as megaAVR 0-series chips like the ATmega4809 as used on the official Nano Every and Uno Wifi Rev. 2 - although the Arduino team has done their best to kneecap them) in the low-cost, small packages typical of the ATtiny line. All of these parts feature at least one hardware UART, and an SPI and TWI interface (none of that USI garbage like, for example, the ATtiny85 has), a powerful event system, configurable custom logic, at least one on-chip analog comparator, a surprisingly accurate internal oscillator, and in the case of the 1-series, an actual DAC output channel, and in the case of the 2-series, a fancy differential ADC.
Moreover, the 0/1/2-series parts are cheap - the highest end parts, the 3216 and 3217, with 32k of flash and 2k of SRAM (same as the atmega328p used in Uno/Nano/ProMini) run just over
These use UPDI programming, not traditional ISP like the classic ATtiny parts did. See below for more information - you can use a classic 328p-based Arduino as programmer v jtag2updi, a serial adapter and a resistor (and preferably a diode) via included pymcuprog tool, one of the Microchip programmers (the mEDBG/nEDBG/EDBG-based programmers on their development board, Atmel-ICE or SNAP) or any UPDI programming tool that emulates one of those (which, to my knowledge, all of them do - if there is one that needs support added. please open an issue to let me know!)
A serial bootloader, Optiboot_x (based on the same codebase as the classical Arduino Uno bootloader) is supported on these parts (0/1-series support is currently live, 2-series is expected by the first week of May; adjustments for the new parts are trivial), allowing them to be programmed over a traditional serial port. See the Optiboot section below for more information on this, and the relevant options. Installing the bootloader does require a UPDI programmer. The assembled breakout boards I sell on Tindie are available pre-bootloaded (they are bootloaded on demand). That being said the user experience with Optiboot is a little disaoppointing on the 0/1-series parts as well as the 14-pin 2-series parts due to their lack of a hardware reset pin that could be used with the usual autoreset circuit to automatically reset into the bootloader when the serial port is opened - you need to either disable UPDI programming entirely (requiring an HV programmer if fuse settings or bootloader need to be change after initial bootloading) or leave UPDI enabbled, but start any upload within 8 seconds of applying power. The 20-pin and 24-pin 2-series parts support an "alternate reset pin" allowing these to act more like a traditional Arduino.
Arduino 1.8.13 is recommended
When megaTinyCore is installed through board manager, the required version of the toolchain is installed automatically. Manual installation - assuming you want support for the 2-series is more complicated; see the Installation guide for more information.
This document is best viewed online if you isntalled via board manager - https://githup.com/SpenceKonde/megaTinyCore
The UPDI programming interface is a single-wire interface for programming (and debugging - Universal Programming and Debugging Interface) used on the tinyAVR 0/1/2-series, as well as all other modern AVR microcontrollers. While one can always purchase a purpose-made UPDI programmer from Microchip, there are two very low-cost approaches to creating a UPDI programmer, both of which the Arduino community has more experience with than those official programmers.
Before megaTinyCore existed, there was a tool called pyupdi - a simple python program for uploading to UPDI-equipped microcontrollers using a serial adapter modified by the addition of a single resistor. But pyupdi was not readily usable from the Arduino IDE, and so this was not an option. As of 2.2.0, megaTinyCore brings in a portable Python implementation, which opens a great many doors; Originally we were planning to adapt pyupdi, but at the urging of its author and several Microchip employees, we have instead based this functionality on pymcuprog, a more robust tool developed and maintained by Microchip which includes the same serial-port upload mechanism. If installing manually you must add the python package appropriate to your operating system in order to use this upload method (a system python installation is not sufficient, nor is one necessary).
As of 2.3.2, with the dramatic improvements in performance, and the proven reliability of the wiring scheme using a diode instead of a resistor, and in light of the flakiness of the jtag2updi firmware, this is now the recommended programming method. As of this version, programming speed has been increased by as much as a factor of 20, and now far exceeds what was possible with jtag2updi (programming via jtag2updi is roughly comparable in speed to programming via SerialUPDI on the "SLOW" speed option, 57600 baud; the normal 230400 baud version programs about three times faster than the SLOW version or jtag2updi, while the "TURBO" option (runs at 460800 baud and increases upload speed by approximately 50% over the normal one. The TURBO speed version should only be used with devices running at 4.5v or more, as we have to run the UPDI clock faster to keep up (it is also not expected to be compatible with all serial adapters - this is an intentional tradeoff for improved performance), but it allows for upload and verification of a 32kb sketch in 4 seconds.
Read the SerialUPDI documentation
One can be made from a classic AVR Uno/Nano/Pro Mini; inexpensive Nano clones are the usual choice, being cheap enough that one can be wired up and then left like that. We no longer provide detailed documentation for this processes; jtag2updi is deprecated.If you are still using it, you should select jtag2updi from the tools->programmer menu. This was previously our recommended option; due to persistent jtag2updi bugs, and it's reliance on the largely unmaintained 'avrdude' tool (which among other things inserts a spurious error message into all UPDI uploads made with it), this is no longer recommended.
Apparently Arduino isn't packaging 32-bit versions of the latest avrdude. I defined a new tool definition which is a copy of arduino18 (the latest) except that it pulls in version 17 instead on 32-bit linux, since that's the best that's available for that platform. The arduino17 version does not correctly support uploading with some of the Microchio programming tools.
This is currently used only for the latest release, and should fix the avrdude not available for this platform error.
- tinyAVR 2-series
- tinyAVR 1-series
- tinyAVR 0-series
- Anything named like "AVR##XX##" where X is a letter and # is a number - you want my DxCore for those
- Any classic (pre-2016) tinyAVR parts - these are supported by ATTinyCore
- ATtiny 25/45/85, 24/44/84, 261/461/861, 48/88, and 43, as well as the late-classical ATtiny 441/841, 1634 and 828.
- The small-and-strange ATtinys: ATtiny26 (support coming to ATTinyCore 2.0.0), and ATtiny43 (already supported).
- The even smaller or stranger ones not supported by ATTinyCore
- ATtiny20/40
- ATtiny13 (just smaller - Use MicroCore by @MCUdude)
- ATtiny15 (obsolete) and ATtiny28 (obsolete, and like, really terrible)
- ATtiny5, 10, 11, and the other "reduced core" devices - these kinda suck. Not only do they have 1k or less flash and practically no RAM, the AVR core they use is gimped. But attiny10core supports them!
- Anything with "Mega" in the name (Use one of @MCUdude's cores)
| tinyAVR series | 0-series | 1-series | 1-series plus | 2-series |
|---|---|---|---|---|
| Pincounts | 8* 14, 20, 24 | 8* 14, 20, 24 | 14, 20, 24 | 14, 20, 24 |
| Flash | 2, 4, 8, 16k | 2, 4, 8k | 16k or 32k | 4k, 8k, 16k, or 32k |
| RAM | 128,256,512,1k | 128,256,512b | 2048b | 512, 1k, 2k, or 3k |
| Separate reset pin? | NO | NO | NO | optional on 20/24pin |
| PWM pins (Arduino) | 8pin: 4 else 6 | 4, 6, or 8 | 6 or 8 | 6 |
| Type A timers | 1 | 1 | 1 | 1 |
| Type B timers | 1 | 1 | 2 | 2 |
| Type D timer | NO | Yes | Yes | No |
| Real Time Clock | Yes, no xtal | Yes | Yes | Yes |
| USARTs (pin options) | 1 (2) | 1 (2) | 1 (2) | 2 (3) |
| SPI port pin options | 1 | 2 except 14-pin | 2 except 14pin | 1 (2 on 20/24pin) |
| TWI port pin options | 1 | 2 except 8-pin | 2 | 1 |
| Maximum rated speed | 20 MHz | 20Mz | 20 MHz | 20 MHz |
| Overclocking (internal @ 5v) | ??? | 25-30 MHz | 25-30 MHz | 32 MHz |
| Overclocking (ext. clk @ 5v) | ??? | 32 MHz | 32 MHz | >= 32 MHz |
| External crystal | NO | NO | NO | NO |
| Event Channels | 1 sync 2 async | 2 sync 4 async | 2 sync 4 async | 6 normal ones |
| CCL Logic Blocks | 2 (1 pair) | 2 (1 pair) | 2 (1 pair) | 4 (2 pairs) |
| Analog Comparators | 1, no DAC REF | 1, w/DAC REF | 3, w/DAC REF | 1, w/DAC REF |
| ADC | 10-bit ADC | 10-bit ADC | 2x 10-bit ADCs | 12-bit diff w/PGA |
| Analog References | .55V, 1.1V, 1.5V, 2.5V, 4.3V | .55V, 1.1V, 1.5V, 2.5V, 4.3V | .55V, 1.1V, 1.5V, 2.5V, 4.3V | 1.024V, 2.048V, 2.5V, 4.096V |
The tinyAVR 2-series has normal event channels, not the weird async/sync ones that the 0/1-series has. They will act as sync or async channels as required (according to the datasheet, each has both a sync and async channel internally)
Very disappointing news - I can see why this is though - adapting the pinout to match the small number of pins means that the pins that things are on for the 8-pin parts isn't the same. It breaks the consistency that the rest of the parts have, where each pin has the same functionality on all parts that have that pin. Let us all just hope that there is a series of 8-pin tinyAVR parts on Microchip's roadmap, and they just decided to leave them out of the 2-series to focus on the core feature (the differential ADC)
The ADC on the 2-series is arguably the best ADC that has shipped on an AVR to date (not counting the xMega line, which is outside the scope of this document and the concerns of the Arduino world). Certainly, outside of the xMega line there is little meaningful competition. The closest comparisons are the classic AVRs that got differential ADCs with top-notch features (the t841, mega2560 and (surprisingly) the t861 being the strongest competitors). While it isn't capable of the insane 100x and 200x gain that some parts bragged of in the classic AVR days, it was never clear to me how much of what was being amplified was simply noise (though considering my admittedly limited experience playing with differential ADCs I'm going to say "probably most of it"). This new ADC is certainly highly capable, with true differential capability (unlike the DA and DB series had), and one which rises head and shoulders above anything available on any other modern AVRs to date. The programmable gain amplifier is a new capability, and it remains to be seen what sort of feats of analog measurement people are able to get out of it; it certainly appears promising. It will be epecially interesting to understand the differences between using the PGA at 0x gain, vs not using the PGA, and the benefits and disadvantages of doing so. (Microchip would be well-served by a documement that discussed how to choose the right ADC configuration for a task in the general case; I have raised this concern with Microchip and the person who I spoke to indicated that it was a high priority.
The addition of 1024-sample accumulation for the purposes of oversampling and decimation is a welcome addition, though one which also risks understating the magnitude and relevance of offset error. (Taking 1024 samples, (all of which have a given offset error), then decimating the sum to yield a 17-bit ADC measurement makes it easy to imagine that any error would be confined to the lowest couple of bits. But if the error was a constant offset, it's magntiude as a fraction of full scale does not change with oversampling and decimation. Software may be able to correct for ADC offset error under various conditions, but there is no guidance on how to do that either.
It would appear that the first full sized chip featuring this ADC will be the EA-series parts, which will be available in 28-48 pin packages with up to 64k flash, according to the available information, from the product brief. Considering that each sub-generation of modern AVRs has featured tweaks to the ADC (which are mostly papered over by the Arduino API), it will be very interesting to see what surprises, if any, are in store for us with the EA-series - the announced information leaves little room for it though, and the 2-series may be more of a trial run (like the 1-series with the TCD) and triple-ADC with window comparator mode..
The type D timer is only used for PWM on 20/24 pin 1-series parts - on the smaller parts, it wouldn't let us increase the total number of PWM pins - Only the WOC and WOD pins (on PC0 and PC1 respectively) don't already have TCA-driven PWM on them. As such, since analogWrite() does not support any features that would be enabled by turning off split mode (like 16-bit PWM) or enhanced by using the type D timer (like adjusting the frequency), it would just be worse, because it would require additional space to store the routine to turn on and off PWM from two types of timer, instead of one. There is one small downside to using TCD for PWM.... nearly 150 bytes of additional overhead added to digital write to turn off the PWM, and over 450 bytes for analogWri
Unlike almost every other AVR ever, the 16k and 32k versions (only) have a few extra features - they all have 2k of ram, whether 16k or 32k, they have 3 analog comparators (including a windoww mode), a second - desperately needed - type B timer - and weirdest of all they have a second ADC, differing only in which pins the channels correspond to!
Overclocked speeds are typical maximum speeds that can be reached with basic functionality intact. Not all parts will reach or function at these speeds, and the operating temperature range is likely far narrower than it is at the rated speeds. I'm aware of nobody who has played with overclocking the 0-series, but as it was released at the same time as the 1-series and appears to be a 1-series with fewer features, I would expect them to be the same - though if they turned out not to be, I could rationalize a difference in either direction equally easily (and even phrase it in a way that makes someone who assumed otherwise look silly: "they're budget parts, likely made with a less advanced process, of course they don't overclock as well!" or "without all those wacky features hanging off the clock, of course they overclock better!").
The internal oscillator speeds can be reached (on most but not all specimens) with tuning. Best results overcocking are (as on classic AVRs) obtained with an external oscillator. Never use an overclocked part in any critical application. neither stability nor correctness of artithmatic can be guaranteed!!
The automotive versions should also work. You must always select the 16 MHz-derived clock speeds on these parts. They do not support 20 MHz operation.
In the official Arduino board definition for their "megaAVR" hardware package, they imply that the new architecture on the megaAVR 0-series parts (which is nearly the same as used on the tinyAVR 0-series and 1-series) is called "megaavr" - that is not an official term. Microchip uses the term "megaAVR" to refer to any "ATmega" part, whether it has the old style or modern peripherals. There are no official terms to refer to all AVR parts of one family or the other. In this document, prior to 2.0.2, we used the Arduino convention, and despite well over a year having passed since then, I still keep finding places where I call them megaAVR. Please report this using a github issue if you see any.
Do note that the terms avr and megaavr are still used internally (for example, in libraries, to mark which parts a given library is compatible with, or separate different versions of a file based on what they will run on). This will continue - we have to stick with this for compatibility with what the Arduino team started with the core for the Uno WiFi Rev. 2 and Nano Every - and in any event, some word is needed to refer to the two groups and Microchip hasn't provided one. Not sure how they managed to develop these very different parts without ever talking about them generally.
It is unfortunate that there are not officially sanctioned terms for these two classes of AVR microcontrollers. I have been referring the pre-2016 AVR devices (with PORTx, DDRx, etc registers for pins) as "classic AVR" and the ones Arduino calls megaavr as "modern AVR"
I buy a lot of electronics stuff on aliexpress. It's a great marketplace for things that are made by Chinese companies and are mostly generic. It is not a great place for the latest semiconductor product lines from major western manufacturers, especially in the midst of a historic shortage of said chips. The modern AVR devices people have bought on there (when they have been found at all - they're rarely offered) have been reported to be fake or defective (like ATtiny412s that think they're 416s). For that matter, you probablty don't want to buy any AVR microcontrollers on aliexpress... Assembled boards, like Arduino Nano clones, generally work if you avoid the ones with the third party LGT8 chips and watch out for the ones with the ATmega168p instead of the '328p - but there are a lot of reports of bogus microcontrollers (I have heard of fake ATtiny85s that were actually remarked ATtiny13s, for example). Buy them from reputable distributors like Digikey or Mouser (if in a hurry, and they're on backorder - which is the case for almost everything in QFN package as of July 2021 - buy from a USA/EU-based scalper).
As of version 2.4.0, we now provide an "Official Microchip Board" option. This doesn't do anything special other than defining LED_BUILTIN to be the pin that has the LED on that board, instead of A7, and defining a macro PIN_BUTTON_BUILTIN defined as the pin with the user button on it and making "upload" with the non-optiboot version always use the onboard programmer/debugger, and tools -> programmer will be used only for "burn bootloader" and "upload using programmer". In the case of the ATtiny416 XPlained Nano, it also selects the version of the bootloader that uses the alternate pins for the serial port - it does not automatically use the alternate pins for USART0 as if you'd done Serial.swap(1) yet - functionality to support default swapping of serial pins will come in a future update, alongside some other changes in the machinery underlying the pinswap mechanism which will hopefully also reduce flash usage.
As noted above, these may not work correctly on 32-bit linux platforms This is beyond my control, I don't build avrdude binaries amd I am not taking on that task too. I have too many already.
Why does blink take more flash on the XPlained Mini vs the XPlained Pro? Even when both have the same ATtiny817
For the same reason that blink will take more flash if you change it to use PIN_PC0 directly instead of letting the board definition to it for you via LED_BUILTIN: PC0, used on the XPlained Mini is a PWM pin, while PB4, used by the XPlained Pro is not. Since that is the only pin that digitalWrite() is being used on, the compiler is free to optimize away anything that isn't needed for digitalWrite() on that pin, including the functionality to turn off PWM output on a pin that supports PWM. The diference vanishes if digitalWrite() is also used on a pin that supports PWM on both devices (or if digitalWrite() is replaced with digitalWriteFast, which assumes that you won't call it on a pin outputting PWM).
I sell breakout boards with regulator, UPDI header, and Serial header in my tindie shop, as well as the bare boards. Buying from my store helps support further development on the core, and is a great way to get started using these exciting new parts with Arduino. Currently ATtiny1624 boards are available, but the 20 and 24-pin parts will not be sold as an assembled board until a newly revised PCB design is back from the board house to enable autoreset on the alt-reset pin. There is also a 14-pin board revision coming - thought it is largely cosmetic. The yellow solder mask has got to go, as the readability seemed to get worse in the last several batches. The new boards also standardize a 0.6" spacing between the rows of pins, instead of the current 0.7" spacing, so you will be able to, for example, put machined pin header onto them and plug them into a wide-DIP socket, or use them with our prototyping board optimized for that row spacing. Assembled 0-series boards are being discontinued, and will not be restocked once they sell out. The same will happen for the 16k 2-series parts once the 32k ones are available.
Datasheet for the new tinyAVR 2-series - While datasheet only "covers" the 16k parts, they clearly state that there are no differences in features between parts with the same pin count (that is, there are no "golden" parts like the 16k/32k 1-series), only between parts with different pin counts. 14, 20, and 24 pin parts are all listed with 4k, 8k, 16k and 32k flash; these flash size options, respectively, come with 512, 1024, 2048, and 3072 bytes of SRAM (that is, the 4k and 8k parts have double the SRAM), 4/8k parts get 128 bytes of EEPROM, the larger ones get 256. 14-pin parts come in SOIC and TSSOP, 20-pin in (wide) SOIC, SSOP, and that itty-bitty QFN like the 1616 (think we'll get the 3226 in that package too? We can hope!), and 24-pin in the same VQFN as the 3217.
TWI, SPI, USART0, AC0, are unchanged, as is NVMCTRL (the changes required to the bootloader were solely in relation to supporting the second USART). Clock options unchanged. TCB0 and TCB1 got upgraded to the version in the Dx-series: clock off event option, cascade, and separate INTCTRL bits for OVF and CAPT - nice additions, but nothing relevant to the core itself), and all the parts have both TCB's. We now get 4 CCL LUTs and 2 sequencers, instead of 2 and 1 - and they can fire interrupts like other parts with CCL (and unlike the tinyAVR 0/1-series). One of the most exciting features is that, as expected, they have a second USART (that noise you hear is the ATtiny841 and and ATtiny1634 sobbing in the corner). PORTMUX registers now named like the rest of the modern AVRs - but we didn't lose the individual control over the pins for each TCA WO channel. EVSYS now works like it does on non-tinyAVR-0/1-series parts (which is a welcome change - the 0/1-series was the odd-one-out, and some of the ways in which their EVSYS was different sucked). The 1-series features of TCD0, AC1/2, DAC0, and ADC1 are gone. In their stead, ADC0 is much fancier and almost unrecognizable, the first new AVR released since the buyout that featured a real differential ADC. (queue another agonized wail from the poor '841, which also has an incredibly fancy ADC with great differential options, but which looks thoroughly dated next to the new ones/)... judging by the volume of posts on different topics that I've seem, I have a sense that differential ADC wasn't at the top of most of your wish-lists - but it was on the top of the major chip customers' lists, and so that's what we're getting one.
And it is really really fancy. The ADC gets a programmable gain amplifier (1x ~ 16x), single-ended and differential mode, a new series accumulation mode (where each sample is triggered by an event) and burst accumulation mode (like our current accumulate mode) - and every sample taken is made individually available, too (and you can have it generate interrupt on each sample or only the final result. They make a big deal about using the accumulate mode to do 1024 sample oversampling - that's 45, so decimation should let us take meaningful 17-bit ADC readings. Rather annoyingly, it only offers 8 and 12-bit resolution options (no 10-bit - megaTinyCore provides a 10-bit resolution option for compatibility by rightshifting a 12-bit reading). It also supports ADC clock between 300khz and 6 MHz (3 MHz with internal reference; we try for approx. 2.5 MHz); to make up for the faster ADC clock, sample duration can be up to 256 ADC clocks; with minimum sample duration, over 300k samples/second is possible. It has more rigorous functionality to time the reference and input settling time too - no more throwing away the first ADC reading? (with parts in hand, I'm going to back away from this claim - I still get a garbage reading the first time). This new ADC is incredibly fancy - just remember that when you are using an accumulation mode, the magnitude of the noise is smaller, but offset error is just as big. Yo do need to compensate tfor thjis somehow (and rigorously too, not haowe ) megaTinyCore provides an analogRead() implementation, and more powerful functions to use the oversampling, PGA, (see the analog feature section below)
Oh, and one more thing... the UPDI pin configuration has the old options - UPDI, I/O, or Reset... and a new one: UPDI on PA0, with hardware RESET pin on PB4! Optiboot will finally be a viable and comfortable option! Well, on the parts that have a PB4, ie, not the 14-pin parts. Which also happen to be (if my Tindie store sales are any indication) the most popular version.
The simple matter of how to refer to a pin for analogRead() and digitalRead(), particularly on non-standard hardware, has been a persistent source of confusion among Arduino users. It's my opinion that much of the blame rests with the decisions made by the Arduino team (and author of Wiring before them) regarding how pins were to be referred to; the designation of some pins as "analog pins" leads people to think that those pins cannot be used for digital operations (they are better thought of as "pins with analog input" - like how there are "pins that can output PWM"). The fact that pins have traditionally been renumbered has further muddied the water. For non-standard classic AVR parts, matters are often made even worse by multiple, incompatible "pin mappings" created by various authors over the years to make the part act "more like an Uno" or for some other purpose (ATTinyCore is a particular mess in this way, with some parts having three entirely different pin mappings, in at least one case, one of the alternate mappings is a devil-inspired work of pure evil, requiring nothing short of an additional lookup table to convert analog pins to digital pins).
This core uses a simple scheme for assigning the Arduino pin numbers: Pins are numbered starting from the the I/O pin closest to Vcc as pin 0 and proceeding counterclockwise, skipping the (mostly) non-usable UPDI pin. The UPDI pin is then assigned to the last pin number (as noted above, it is possible to read the UPDI pin (both analog and digital reads work) even if it is not set as GPIO). We recommend this as a last resort: the UPDI pin always has it's pullup enabled when not set as a GPIO pin, and a signal which looks too much like the UPDI enable sequence will cause undesired operation.
In order to prevent all confusion about pin identities and eliminate ambiguity, we recommend using the PIN_Pxn notation to refer to [pins unless you are using a development board with different numbers or names for the pins printed on it. This will maximize portability of your code to other similar hardware and make it easier to look up information on the pins you are using in the relevant datasheets should that be necessary.
This is the recommended way to refer to pins Defines are also provided of form PIN_Pxn, where x is A, B, or C, and n is a number 0-7 - (Not to be confused with the PIN_An defines described below). These just resolve to the digital pin number of the pin in question - they don't go through a different code path or anything. However, they have particular utility in writing code that works across the product line with peripherals that are linked to certain pins (by Port), as most peripherals are. Several pieces of demo code in the documentation take advantage of this. Direct port manipulation is possible as well - and in fact several powerful additional options are available for it - see direct port manipulation.
PIN_Pxn - not Pxn, and not PIN_xn - those mean different things!
When a single number is used to refer to a pin - in the documentation, or in your code - it is always the "Arduino pin number". These are the pin numbers shown in orange (for pins capable of analogRead()) and blue (for pins that are not) on the pinout charts. All of the other ways of referring to pins are #defined to the corresponding Arduino pin number.
The core also provides An and PIN_An constants (where n is a number from 0 to 11). As with the official core, PIN_An is defined as the digital pin number of the pin shared with analog channel n These refer to the ADC0 channel numbers. This naming system is similar to what was used on many classic AVR cores but here, they are just #defined as the corresponding Arduino pin number. If you need to get the analog channel number on a digital pin, use the digitalPinToAnalogInput(pin) macro - but you only need that if you're writing an advanced ADC library.
These parts (well, the 1/2-series at least - the 0-series is more of a budget option) provide an excellent toolbox of versatile and powerful peripherals; the top-end ones are on a par with or better than classic megaAVR parts - for a tinyAVR price. One of the guiding principles of the design of megaTinyCore, as with my other cores, is to allow the supported parts to reach their full potential - or as close to that as possible within the limitations of Arduino. This (very large) section covers the features of these parts and how they are exposed by megaTinyCore, as well as features of the core itself. This (very large) section attempts to cover each of the feature areas. Do try to find the feature you are working with if you're trying to use some chip feature and having trouble!
- 20 MHz Internal (4.5v-5.5v - typical for 5v systems)
- 16 MHz Internal (4.5v-5.5v - typical for 5v systems)
- 10 MHz Internal (2.7v-5.5v - typical for 3.3v systems)
- 8 MHz Internal (2.7v-5.5v - typical for 3.3v systems)
- 5 MHz Internal (1.8v-5.5v)
- 4 MHz Internal (1.8v-5.5v)
- 1 MHz Internal (1.8v-5.5v)
- 20 MHz Internal (tuned)
- 16 MHz Internal (tuned)
- 12 MHz Internal (tuned)
- 20 MHz External Clock (4.5v-5.5v)
- 16 MHz External Clock (4.5v-5.5v)
- 12 MHz External Clock (2.7v-5.5v)
- 10 MHz External Clock (2.7v-5.5v)
- 8 MHz External Clock (2.7v-5.5v)
- 24 MHz Internal (tuned, overclocked)
- 25 MHz Internal (tuned, overclocked)
- 30 MHz Internal (tuned, overclocked) - 0/1-series require "20MHz" OSCCFG fuse setting; 2-series parts may or may not be able to reach 30 with "16 MHz" selected.
- 32 MHz Internal (tuned, overclocked) - 2-series only, very optimistic overclocking, may be unstable.
- 24 MHz External clock (Overclocked)
- 25 MHz External clock (Overclocked)
- 30 MHz External clock (Overclocked aggressively)
- 32 MHz External clock (Overclocked aggressively)
Important - Read about Tuning before selecting any tuned option!
More information on these clock speeds can be found in the Clock Reference
Voltages shown are those guaranteed by to work by manufacturer specifications. Unless pushing the bounds of the operating temperature range, these parts do far better (2-series generally work at 32 MHz and 5v @ room temperature even from internal oscillator; the 0/1-series will likewise usually work at 32 MHz with external clock provided the power supply is a stable 5.0-5.5V).
No action is required to set the OSCCFG fuse when the sketch is uploaded via UPDI. When uploaded through Optiboot, the fuse cannot be changed, so whatever was chosen when the bootloader was burned is what is used, and only "burn bootloader" or uploading a sketch via UPDI will change that.
All internal oscillator clock speed options use the factory default calibration unless a "tuned" option is selected, in which case the calibration is adjusted as documented in the tuning documentation.
See Speed Grade reference for more information on the manufacturer's speed grades. Note that those are the voltages and clock speeds at which it is guaranteed to work, where an unexpected glitch of some description could pose a hazard to persons or property. Under favorable temperatures (ie, room temperature), and with higher tolerance for potential stability issues than a commercial customer, the speed grades can easily be beaten. Our testing has found that the official speed grades are extremely conservative.
Unlike classic AVRs, on the these parts, the flash is within the same address space as the rest of the memory. This means pgm_read_*_near() is not needed to read directly from flash. Because of this, the compiler automatically puts any variable declared const into PROGMEM, and accesses it appropriately - you no longer need to explicitly declare them as PROGMEM. This includes quoted string literals, so the F() macro is no longer needed either (As of 2.1.0, F() once more explicitly declares things as living in PROGMEM (ie, it is slightly less efficient) in order to ensure compatibility with third party libraries).
However, do note that if you explicitly declare a variable PROGMEM, you must still use the pgm_read functions to read it, just like on classic AVRs - when a variable is declared PROGMEM on parts with memory mapped flash, the pointer is offset (address is relative to start of flash, not start of address space); this same offset is applied when using the pgm_read_*_near() macros. Do note that declaring things PROGMEM and accessing with pgm_read_*_near functions, although it works fine, is slower and wastes a small amount of flash (compared to simply declaring the variables const); the same goes for the F() macro with constant strings in 2.1.0 and later (for a period of time before 2.1.0, F() did nothing - but that caused problems for third party libraries, and the authors maintained that the problem was with the core, not the library, and my choice was to accept less efficiency, or deny my users access to popular libraries). Using the F() macro may be necessary for compatibility with some third party libraries (the specific cases that forced the return of F() upon us were not of that sort - we were actually able to make the ones I knew of work with the F()-as-noop code, and they took up a few bytes less flash as a result).
These parts all have a large number of analog inputs. The 0/1-series have a 10-bit ADC - sometimes 2 for the 16k and 32k 1-series parts, while the 2-series has one of the most advanced ADCs ever featured on an AVR, with 12 bit resolution and true differential measurement capability. They can be read with analogRead() like on a normal AVR, and we default to 10-bit resolution; you can change to the full 12-bit with analogReadResolution(), and use the enhanced analogRead functions to take automatically oversampled, decimated readings for higher resolution and to take differential measurements. There major differences between the 0/1-series and the 2-series, and that is all detailed in the ADC reference.
The 1-series parts have an 8-bit DAC which can generate a real analog voltage (note that this provides low current and can only be used as a voltage reference or control voltage, it cannot be used to power other devices). This generates voltages between 0 and the selected VREF - which cannot be Vdd, unfortunately. Set the DAC reference voltage via the DACReference() function - pass it any of the ADC reference options listed under the ADC section above (except VDD). Call analogWrite() on the DAC pin (PA6) to set the voltage to be output by the DAC. To turn off the DAC output, call digitalWrite() or turnOffPWM() on that pin.
See the ADC and DAC Reference for the full details.
Using the An constants is deprecated - the recommended practice is to just use the digital pin number, or better yet, use PIN_Pxn notation when calling analogRead(). Particularly since the release of 1.3.0 and megaTinyCore 2.3.0, a number of enhanced ADC features have been added to expose more of the power of the sophisticated ADC in these parts to users.
There are more options than on classic AVR for resetting, including if the code gets hung up somehow. The watchdog timer can only reset (use the RTC and PIT for timed interrupts) See the Reset and Watchdog (WDT) Reference
This core adds a number of new features include fast digital I/O (1-14 clocks depending on what's known at compile time, and 2-28 bytes of flash, and for configuring all per-pin settings the hardware has with pinConfigure()
See the Improved Digital I/O Reference
All of the 0/1-series parts have a single hardware serial port (UART or USART); the 2-series parts have two. It works exactly like the one on official Arduino boards (except that there is no auto-reset, unless you've wired it up by fusing the UPDI pin as reset (requiring either HV-UPDI or the Optiboot bootloader to upload code), or set up an "ersatz reset pin" as described elsewhere in this document). See the pinout charts for the locations of the serial pins.
Prior to putting the part into a sleep mode, or otherwise disabling it's ability to transmit, be sure that it has finished sending the data in the buffer by calling Serial.flush(), otherwise the serial port will emit corrupted characters.
See the Serial Reference for a full list of options - as of 2.5.0 almost every type of functionality that the serial hardware can do is supported, including RS485 mode, half-duplex (via LBME and ODME), and even synchronous and Master SPI mode!
All of these parts have a single hardware SPI peripheral. It works like the one on official Arduino boards using the SPI.h library. See the pinout charts for the location of these pins. On 8-pin parts, the only option for the SS pin is PA0 (the UPDI/reset pin); this does not matter for the purposes of this core though, because, like the official library, this only operates as a master, and the SS pin is used only when potentially acting as a slave.
On all parts except the 14-pin parts, the SPI pins can be moved to an alternate location (note: On 8-pin parts, the SCK pin cannot be moved). This is configured using the SPI.swap() or SPI.pins() methods. Both of them achieve the same thing, but differ in how you specify the set of pins to use. This must be called before calling SPI.begin().
SPI.swap(1) or SPI.swap(0) will set the the mapping to the alternate (1) or default (0) pins. It will return true if this is a valid option, and false if it is not (you don't need to check this, but it may be useful during development). If an invalid option is specified, it will be set to the default one.
SPI.pins(MOSI pin, MISO pin, SCK pin, SS pin); - this will set the mapping to whichever mapping has the specified pins. If this is not a valid mapping option, it will return false and set the mapping to the default. This uses more flash than SPI.swap(); that method is preferred. The SS pin argument is optional, as the pin is not used when acting as an SPI master, and neither this library nor the official SPI.h library support acting as a slave.
When it can be determined that arguments passed to SPI.swap() or SPI.pins() are invalid at compile time (most commonly when the argument(s) are constants, which they almost always are), the core will generate a compile error to that effect. This is meant to help prevent such detectable problems from requiring debugging time on hardware - there's never a right time to usse
This core disables the SS pin - this means that the "SS" pin can be used for whatever purpose you want, and the pin is relevant only when making an SPI slave (which requires you to implement the interaction with the SPI peripheral yourself - though it's not rocket science or anything). On the classic AVRs, if SS was an input and SPI was enabled, it was acting as the SS pin, and if it went low, it would switch the device to slave mode (and SPI.h would not function until put back into master mode, which was not done automatically).
All of these parts have a single hardware I2C (TWI) peripheral. It presents an API compatible with the standard Arduino implementation, but with added support for multiple slave addresses, answering general call addresses - and most excitingly, simultaneous master and slave operation! (new in 2.5.0)
This is fully documented in the Wire library reference
The core provides hardware PWM via the standard analogWrite() function. On the 8-pin parts (412, 212, 402, 204), 4 PWM pins are available. On all other parts except 1-series parts with 20 or 24 pins, 6 PWM pins are available, all driven by Timer A. The 20 and 24 pin 1-series parts have two additional pins, driven by TCD0. The 2-series apparently traded TCD0 for a second serial port and a super-fancy ADC - those parts also all have 6 PWM pins. The Type B timers cannot be used for additional PWM pins - their output pins are the same as those available with Timer A and they are often too useful to justify using a whole TCB for - however you can take them over if you need to generate PWM at different frequencies, though the fact that the prescaler cannot differ from the type A timer limits this use as well. See the pinout charts for a list of which pins support PWM.
Note that TCA0 (the type A timer) on all parts is configured by the core at startup to operate in split mode in order to support the most PWM pins possible with analogWrite(). As of the 2.2.x versions, a takeOverTCA0() function has been added, which can be called to instruct the core not write to TCA0-registers nor assume any particular mode or behavior for TCA0. analogWrite() will not generate PWM except on pins driven by TCD0 on the 20/24-pin parts nor will digitalWrite turn it off if you want to reconfigure TCA0 for other purposes, please refer to the below guide and "hard reset" the timer back to stock configuration.
The 3216, 1616, 816, 416, and the 3217, 1617 and 817 have two additional PWM pins driven by Timer D (PC0 and PC1 - pins 10 and 11 on x16, 12 and 13 on x17). Timer D is an async timer, and the outputs can't be enabled or disabled without briefly stopping the timer. This results in a brief glitch on the other PWM pin (if it is currently outputting PWM), and doing so requires slightly longer - though the duration of this glitch is under 1 us. If TCD is used as the millis timer - which is the default on any part that has a type D timer (in order to keep the timers that are more readily repurposed available - TCD0 is not an easy peripheral to work with), this will result in millis losing a very small amount of time (under 1 us) every time PWM is turned on or off on a TCD pin.
As of 2.2.0, analogWrite of 0 or 255 on a TCD-driven PWM pin does not disconnect the pin from the timer - instead it results in a constant HIGH or LOW output without disconnecting the timer(use digitalWrite() for that). This means that analogWrite(PIN_PC0 or PC1, 0) can be used to connect the timer to the pin without outputting PWM (yet) - doing this on both pins prior to setting any other duty cycles would allow one to ensure that no glitch of any sort occurs on the other TCD0 pin when the second pin is connected to it. Only digitalWrite() will disconnect the timer from the pin. When outputting a HIGH in this way, the pin is "inverted"; this means that digitalRead() on it will return 0, not 1 (if you're digitalRead'ing a pin, which you have set to output a constant HIGH, using analogWrite, and it's one of those two pins, it will read LOW - however, if you are using digitalRead() on a pin that you've set to output a constant value, you may be doing something wrong in general.
There is a benefit of having an async timer, however: megaTinyCore configures it to use the unprescaled internal oscillator as it's clock source. This means that while there is a difference in PWM frequency between 16-MHz derived and 20-MHz derived clocks, there is no change in frequency for different system clock speeds for the TCD-controlled pins (the TCA-controlled pins will ) The exception to this is when TCD0 is used as the millis/micros timing source at 1 MHz - running at full speed there resulted in spending an unreasonable fraction of runtime in the millis ISR (tens of percent of the time.
On some versions of megaTinyCore prior to 2.2.0, PWM on the TCD0 pins was entirely broken.
For general information on the available timers and how they are used PWM and other functions, consult the guide: This also covers the PWM frequencies that these timers will give you at various system clocks.
Support for tone() is provided on all parts using TCB0, unless TCB1 is present and TCB0 is set as millis source. This is like the standard tone() function. Unlike on some classic AVRs, it does not support use of the hardware output compare to generate tones - due to the very limited PWM capabilities and restricted prescaler selection for the TCBs, this is not practical. See caveats below if using TCB0 or TCB1 for millis/micros settings. On parts with 8k or less flash, tones which specify a duration longer than 65536ms and a high frequency (specifically where duration times frequency is >4.2 billion) are not supported - if specified at compile time it will generate a compile error, and at runtime, it will produce a shorter duration tone than expected - this is a trade-off to reduce flash usage. It was decided that requesting a tone over a minute long (several minutes continuous at the upper limit of human hearing would be required to trigger the issue, and it would need to be even longer as the frequency got lower) qualifies as highly abnormal usage of tone(). At that point, rather than counting the number of times the tone pin is toggled (like tone() with a duration specified does), it probably makes more sense to use durationless tone(), and turn it off with noTone(). Or, for the sake of everyone within earshot, m ybe don't make your device emit a high pitched tone for minutes on end at all? On parts with 16k flash or more a slightly less flash efficient implementation is used and the limit is significantly higher and very unlikely to be encountered.
Tone can only play a tone on one pin at a time. In theory you can play one tone per typeB timer, simultaneously, without anything more exotic than what tone() does now other than adding a capability to manage the multiople pins. It is my opinion that those belong in a library, not the core, See comments in core.cpp for some thoughts if you want to implement something like that - I'd be happy to give more thoughts if you have questions.
megaTinyCore provides the option to use any available timer on a part for the millis()/micros timekeeping, controlled by a Tools submenu - or it can be disabled entirely if needed to save flash, allow use of all timer interrupts, or eliminate the periodic background interrupt. By default, TCD0 will be used by on parts that have one - otherwise TCA0 will be used (in versions prior to 1.1.9, TCA0 was used by default on parts that could output PWM with TCD0 on pins not available for TCA0 PWM). All timers available on the parts can be used: TCA0, TCD0 (on parts that have it), TCB0, TCB1 (where present) and the RTC. Many of these - particularly the non-default options, involve tradeoffs. In brief, TCA0 is a very versatile timer that users often want to reconfigure, TCD0 loses a small amount of time when PWM is turned on or off on the two TCD0 PWM pins (10,11 on 20-pin parts, 12,13 on 24-pin parts), TCB0 conflicts with Servo and tone on parts that don't have TCB1, and when the RTC is used micros() is not available at all because the clock isn't fast enough. With these limitations in mind, the timer selection menu provides a way to move millis()/micro to the timer most appropriate for your needs.
For more information, on the hardware timers of the supported parts, and how they are used by megaTinyCore's built-in functionality, see the Timers and megaTinyCore
2.3.0 fixed a long-standing (though surprisingly low impact) "time travel" bug where the
If the RTC is selected as the timer for millis timekeeping, micros will not be available. Additionally, this timer will be configured to run while in STANDBY sleep mode. This has two important consequences: First, it will keep time while in sleep. Secondly, every 64 seconds, the RTC overflow interrupt will fire, waking the chip - thus, if you are using the RTC for millis and putting the part into sleep, you should declare a volatile global variable that you set in the ISR that is supposed to wake the part, eg 'volatile boolean ShouldWakeUp=0;' - set it to 1 in the ISR, and when you put the ATtiny to sleep, have it check this immediately after waking, going back to sleep if it's not set, and clearing it if it is, e.g.:
void GoToSleep() {
do {
sleep_cpu();
} while (!ShouldWakeUp)
ShouldWakeUp=0;
}This functionality will be made easier to use via ModernSleep whern that library is available.
This board package also supports using an external 32.768khz crystal as the clock source for the RTC (not supported on 0-series or 8-pin parts). If this is used, make sure that the crystal is connected between the TOSC1 and TOSC2 pins (these are the same as the TX and RX pins with the default pin mapping, unfortunately), that nothing else is, that no excessively long wires or traces are connected to these pins, and that appropriate loading capacitors per crystal manufacturer datasheet are connected. I found the 32k crystal to be extremely uncooperative. To reduce power usage, they try to drive the crystal as weakly as they can get away with, which in turn makes it more susceptible to interference.
Yes, you can use an external oscillator for the RTC, at least on 1 and 2 series parts. When it's an oscillator not a crystal,It can be fed to either TOSC0 or CLKI; better support for this will come in the future.
Unlike the official board packages, but like many third party board packages, megaTinyCore includes the printf() method for the printable class (used for Serial and many other libraries that have print() methods); this works like printf(), except that it outputs to the device in question; for example:
Serial.printf("Milliseconds since start: %ld\n", millis());Note that using this method will pull in just as much bloat as sprintf() and is subject to the same limitations as printf - by default, floating point values aren't printed.
You can choose to have a full printf() implementation from a tools submenu if you want to print floating point numbers
There are a considerable number of ways to screw up with printf. Some of the recent issues that have come up:
- Formatting specifiers have modifiers that they must be paired with depending on the datatype being printed, for all except one type. See the table of ones that I expect will work below (it was cribbed from cplusplus.com/reference/cstdio/printf/, and then I chopped off all the rows that aren't applicable, which is most of them). Apparently many people are not fully aware (or at all aware) of how important this is - even when they think they know how to use printf(), and may have done so on previously (on a desktop OS, with 32-bit ints and no reason to use smaller datatypes for simple stuff).
- There are (as of 1.4.0) warnings enabled for format specifiers that don't match the the arguments, but you should not rely on them. Doublecheck what you pass to printf - printf bugs are a common cause of software bugs in the real world. Be aware that while you can use F() on the format string, there are no warnings for invalid format strings in that case; a conservative programmer would first make the app work without F() around the format string, and only switch to F() once the format string was known working.
From cplusplus.com:
The length sub-specifier modifies the length of the data type. This is a chart showing the types used to interpret the corresponding arguments with and without length specifier
(if a different type is used, the proper type promotion or conversion is performed, if allowed): Strikethrough mine 'cause that don't work here (and it's not my fault nor under my control - it's supplied with avrlibc, and I suspect that it's because the overhead of implementing it on an 8-bit AVR is too large) - When incorrect length specifiers are given (including none when one should be used) surprising things happen. It looks to me like all the arguments get smushed together into a group of bytes. Then it reads the format string, and when it gets to a format specifier for an N byte datatype, it grabs N bytes from the argument array, formats them and prints them to whatever you're printing to, proceeding until the end of the format string. Thus, failing to match the format specifiers' length modifiers with the arguments will result in printing wrong data, for that substitution and all subsequent ones in that call to printf.
The table below is the relevant lines from that table - many standard types are not a thing in Arduino.
| length | d i | u o x X | f F e E g G a A | c | s | p | n |
|---|---|---|---|---|---|---|---|
| (none) | int16 | uint16 | float | int | char* | void* | int* |
| hh | int8 | uint8 | char* | ||||
| l | int32 | uint32 | int32_t* |
Notice that there is no line for 64 bit types in the table above; these are not supported (support for 64-bit types is pretty spotty, which is not surprising. Variables of that size are hard to work with on an 8-bit microcontroller). This applies to all versions of printf - the capability is not supplied by avrlibc.
A tools submenu lets you choose from full printf() with all features, the default one that drops float support to save 1k of flash, and the minimal one drops almost everything and for another 450 bytes (will be a big deal on the 16k and 8k parts. Less so on 128k ones.) - note that selecting any non-default option here will cause it to be included in the binary even if it's never called - and if it's never called, it normally wouldn't be included. So an empty sketch will take more space with minimal printf selected than with the default, while a sketch that uses printf will take less space with minimal printf vs default.
All pins can be used with attachInterrupt() and detachInterrupt(), on RISING, FALLING, CHANGE, or LOW. All pins can wake the chip from sleep on CHANGE or LOW. Pins marked as ASync Interrupt pins on the megaTinyCore pinout charts (pins 2 and 6 within each port) can be used to wake from sleep on RISING and FALLING edge as well. Those pins are termed "fully asynchronous pins" in the datasheet
Advanced users can instead set up interrupts manually, ignoring attachInterrupt and manipulating the relevant port registers appropriately and defining the ISR with the ISR() macro - this will produce smaller code (using less flash and RAM) and the ISRs will run faster as they don't have to check whether an interrupt is enabled for every pin on the port.
For full information and example, see the Interrupt Reference
The Sketch -> Export Compiled Binary option has been significantly enhanced in megaTinyCore and it now provides a record of settings when the export was performed, and assembly listings and s memory map to assist in optimization and reducing flash usage.
See the Export Reference
These parts officially support BOD trigger levels of 1.8V, 2.6V, and 4.2V, with Disabled, Active, and Sampled operation options for when the chip is in Active and Sleep modes - Disabled uses no extra power, Active uses the most, and Sampled is in the middle. As of 2.1.0, the active/sleep modes have been combined into a single menu, the nonsensical options (such as using more aggressive BOD is while sleeping than while awake) removed, and the previously unexposed options added: sampled mode is now available with two sample rates (the faster one uses ever so slightly more power, as you would expect), and "Enabled hold wake" - in that mode, BOD is disabled in sleep, enabled when not sleeping, and when waking up, code execution does not begin until the BOD is ready. See the datasheet for details on power consumption and the meaning of these options. You must do Burn Bootloader to apply this setting, even in 2.2.0 and later; it's not a "safe" setting, since if you set it to a voltage higher that the operating voltage and enable it, the chip is "bricked" until a high enough voltage is applied.
Between the initial header file and preliminary datasheet release, and the more recent versions of each, several BOD settings were removed from the tinyAVR 0/1-series datasheets, and the atpack release notes described them as "unqualified" - (described as "unqualified" in the release notes accpompanying this change - I understand that this has something to do with the vetting process for critical applications which these parts go through and do not correspond to a voltage above which the chip is guaranteed to function under certain conditions (The three official BOD levels are the voltages that the chip is guaranteed (Yup, they use that word in the datasheet!) to work within the manufacturer specified temperature range running at a system clock frequency no higher than marked, and it has been implied that ongoing tests of production devices are performed it would appear that their policy is to test against that this is tested in production. In contrast, the other 5 BOD levels are expected to work as one would expect, but Microchip does not provide any guarantee that they'll work, even if all other design requirements are met. were removed from the datasheet and header files. These are supported by the megaTinyCore BOD dropdown menu, but (as of 2.0.4 - the first version that has the new headers) are marked as such in the submenu. Note that the new headers no longer provide the *_gc enum entries for these BOD levels.
Whenever a UPDI programmer is used to upload code, all fuses that can be set "safely" (as in, without risk of bricking the board, or bricking the board if one does not have access to an HV programmer), and which have any built-in configuration options, will be set. Thus, except where noted, behavior will always match the selected tools menu. In summary, these are handled as follows:
WDTCFG will not be changed - it is not configured by megaTinyCore except to reset it to the factory default when doing "burn bootloader".
BODCFG will not be changed - not safe, you could set the bod level to 4.3 on a 3.3v system, and then it would need to get >4.3v applied to reprogram it. If it is on the same circuit board as parts that would be damaged, this is a difficult situation to recover from.
OSCCFG will be set
TCD0CFG will not be changed - it is not configured by megaTinyCore except to reset it to the factory default when doing "burn bootloader".
SYSCFG0 will not be changed - not safe
SYSCFG1 will be set
APPEND will not be changed - it is not configured by megaTinyCore. There is insufficient demand to justify the development effort.to make use of this as DxCore does
BOOTEND will be set
LOCKBIT will not be changed - it is not configured by megaTinyCore; supporting the lockbits presents several additional complications, and commercial users with need of this facility are unlikely to be using the Arduino IDE to program production units.
BODCFG is not safe, because setting this to a higher voltage than board is running at and enabling it will "brick" the board until a higher operating voltage can be supplied; this could be particularly awkward if it is soldered to the same PCB as devices which will not tolerate those voltages.
SYSCFG0 is not safe because this is where RSTPINCFG lives; changing this can leave the board unprogrammable except via HV UPDI programming, and not everyone has an HV UPDI programmer. In the future if/when a programmer that guarantees HV UPDI capability which can be selected as a programmer (ie, it becomes possible to make a tools -> programmer option which will only work with HV programmers) this fuse will be set automatically when using that programmer.
As a result in 2.2.0 and later, you no longer need to 'burn bootloader' to switch between 16-derived and 20-derived speeds when uploading using UPDI
This core always uses Link Time Optimization to reduce flash usage - all versions of the compiler which support the tinyAVR 0/1/2-series parts also support LTO, so there is no need to make it optional as was done with ATTinyCore.
In general you should expect the following about library compatibility:
- Anything that works on an Uno WiFi Rev. 2 or Nano Every should work or require minimal effort to convert (if you run into one that doesn't work, please let us know in either discussions or issues, so we can look into getting it working correctly. I always want to know to add to the table linked below, but particularly if it works on those boards but not here - they are very similar architectures, and any porting effort required should be minimal. The most likely explanation is that the library tested specifically for the ATmega4809, rather than generally for the peripherals it used.
- The library.properties field
architectures=*would suggest that it would work anywhere - all this means is that there are not separate folders with implementations for different architectures. It does not mean that the library does not make assumptions about architecture, test against architecture specific stuff with #ifdefs and so on. - Libraries that work on other AVR-based arduino devices will work as long as:
- They do not directly interact with hardware registers,
- They do not make assumptions about what pins are associated with their peripheral (ex "Okay, now my library has included Wire.h, now I'm going to attachInterrupt() on SDA: attachInterrupt(A4,myInterrupt);) - that fails except on an '328, because it assumes that SDA is on the same pin as analog input 4 - for example);
- Libraries that make use of only Arduino API calls without assumptions about the underlying hardware are virtually guaranteed to work.
The amount of effort required to port a given library will vary widely depending on the library. Some are almost trivial, while others require deep knowledge. The fact that many libraries can be ported without much effort again underlines the need for reports from users about incompatible libraries so we can pick this lowhanging fruit,
I know lots of people use libraries that aren't on that list, and I fully expect that there is a great number of libraries that work and are not listed, and I'd live to hear about them. Use the "discussions", or email me, or even submit a PR to add a line to the table. And while I'm happy to hear about working librariesm I'm even more interested if you have tried some and found that they don't work, so I can figure out why and how much effort would be required to make them work.
Most existing Arduino libraries work (see the Supported Libraries List for a more complete list and discussion of what kinds of libraries might have issues). Of the few libraries that don't work, a handful happened to also be extremely popular and heavily used, such that it was felt necessary to include a compatible version with the core. In addition to these, libraries which expose hardware only present on the modern AVRs are also included. These libraries are listed below.
The usual NeoPixel (WS2812) libraries, including the popular FastLED as well as AdafruitNeoPixel, have problems on these parts - they depend on hand-tuned assembly, but the execution time of several key instructions has been improved; the improvements enable significant simplification of the code for driving these LEDs. This core includes a compatible version of the tinyNeoPixel library for interfacing with these ubiquitous addressable LEDs. There are two versions, both tightly based on the Adafruit_NeoPixel library - one implements a truly identical API, differing only in name. (Well, and obviously the fact that it works on tinyAVR and Dx-series and megaAVR 0-series parts at clock speeds from 8 MHz to 48 MHz, instead of on most classic AVRs at 8, 12, and 16 MHz). The other version makes a slight change to the constructor and drops support for changing length at runtime, in order to realize significant flash savings (around 1k). See the tinyNeoPixel documentation and included examples for more information.
The standard EEPROM.h is available here - it works like it does on any AVR. USERSIG.h (from "User Signature" which the datasheet has sometimes called the USERROW) it has the same API as EEPROM, though there may be future additions to harmonize with Dx-friendly functions for updating multiple bytes - the Dx-series parts can only erase the whole USERROW, so potentially each byte written could involve erasing and rewriting it all - the question of how to deal with that is why DxCore doesn't have a USERSIG library yet). The name "USERSIG" refers to the alternate name of the USERROW, the "User Signature" space - the name USERROW could not be used because it is defined by the io headers (it's the struct of type USERROW_t, made up of USERROW.USERROW0 through USERROW.USERROW31. Not the most useful thing, but we never override the io header file definitions unless working around a bug.
Note: Prior to 2.1.0, we tried to get clever with supporting the USERROW through the EEPROM library; that not only was shortsighted (as it's logically inconsistent on anything with more than 256b of EEPROM), it also introduced some serious bugs. Use the USERSIG.h library for that instead.
The usual Servo library from library manager is incompatible with these parts (minor changes could make it "work", but with glaring issues and a dependence on the configuration of TCA0). This core provides a version of the Servo library which will select an appropriate timer (TCB0 is the only option on most parts, on parts with a TCB1 (2-series and 3216, 3217, 1617, 1616 and 1614), TCB1 will be used instead, provided it's not being used for millis()). Except on parts with a TCB1, tone cannot be used at the same time as the Servo library. Servo output is better at higher clock speed - when using servos, it is recommended to run at the highest frequency permitted by the operating voltage to minimize jitter.
Warning If you have installed a version of the Servo library to your /libraries folder (including via library manager), the IDE will use that version of the library (which is not compatible with these parts) instead of the one supplied with megaTinyCore (which is). As a workaround, a duplicate of the Servo library is included with a different name - to use it, just #include <Servo_megaTinyCore.h> instead of #include <Servo.h> - no other code changes are necessary.
Note that the Servo libraries were only fixed in version 2.2.0 - prior to that we had a Servo library, but it didn't work due to an astonishingly large number of bugs (I swear I tested it!)
Written by @MCUDude, this provides a more accessible (much more accessible!) wrapper around the optiboot.h library (which was written by the famous @westfw) . This supports writing to the flash of any device using Optiboot, by having the application code call routines in the bootloader to write to the flash (All modern AVRs have built-in flash protection mechanisms that permit only code executing from the bootloader section (BOOTCODE, in their terminology) to write to the application section (APPCODE)). While the hardware does support a third flash section (APPDATA) which can be written by code running in APPCODE this is only usable if there is also a BOOTCODE section defined (otherwise the entire flash is treated as BOOTCODE which can never be self-programmed), and would require a separate implementation of this library to use. It would also be possible to get flash-write-from-app without use of an actual bootloader through an analog of the trick used by the DxCore Flash.h for this. Since there appears to be little demand for such a thing, that functionality is not currently implemented (they were implemented on DxCore's flash writing library because the additional effort was virtually nil, and because there was a user with a particuluar interest in that feature). If someone wants this, and will adapt the library, I can add the entry point to the core and give you little chunks of inline assembly that will call it.) (Note on terminology - on AVR Dx-series, the fuses are called BOOTSIZE and CODESIZE whereas on 0/1-series tinyAVRs they're called BOOTEND and APPEND. I'm not quite sure how they didn't forsee customer confusion when they called the "APPlication END" that... regardless of the names, they do the same thing (though the granularity on tinyAVRs is finer, as you would expect).
Optiboot_flasher documentation
Warning As noted above, there is a library for DxCore that is also named Flash.h. Both allow an application to write to the flash using Optiboot if present. That is the only similarity they have. The API, NVM hardware, method used to call the bootloader, and basically everything about these libraries is different. Be sure you write code for the one that matches the hardware you're using. While I (Spence Konde) wrote the DxCore one, I don't have a particularly strong opinion about which way is "right" - we made them independently, but not because we each thought the other one's idea of how it should be done was wrong. They largely reflect the way the hardware interacts with it's flash; for example the one for megaTinyCore is page-oriented, with it's own page buffer - and these parts write in a page-oriented manner - while the DxCore library only cares about pages when erasing - and indeed, on those parts, the flash is written with word or byte granularity.
All of these parts have at least a pair of Configurable Custom Logic (CCL) blocks; Each block allows you to supply an arbitrary 3-input truth table, as well as configuring other aspects of the logic block. The CCL operates asynchronously - meaning that things can happen faster than the clock speed, (though there is optional synchronizer) be synchronized to an event input or the system clock. The inputs can come from pins, events, or other peripherals; there's a feedback input (as well, which allows a great many exciting possibilities) and a "sequencer" that can act like a latch or flip-flop using the outputs of a pair of logic blocks as it's inputs. This is an incredibly powerful peripheral - especially on the 2-series parts, which have a second pair of logic blocks, as well as the capability to trigger an interrupt when the state of one changes.
This library provides a simple wrapper around the CCL hardware in the tinyAVR 0/1/2-series devices. This library is also included in DxCore and MegaCoreX, covering all AVRs with CCL hardware. Written by @MCUDude.
Nomenclature note: Microchip often refers to the "logic blocks" as "LUTs" - "LUT" being an abbreviation for "Lookup table", which is a central feature of a logic block (it's a very small lookup table though - 3 binary inputs gives 8 entries in the lookup table, which are either 1 or 0, so 1 bit each. 8 bits is a byte last I checked, so it's a bit smaller than than most things one would refer to as a table. We use the term "logic block" in the documentation (which includes the lookup table, it's input multiplexers, and it's synchronizer/filter and edge detector) unless we are specifically referring to the lookup table. This also helps to avoid any confusion with other types of lookup tables,
These parts have either 1 or 3 (1614, 1616, 1617, 3216, and 3217) on-chip analog comparators which can be used to compare two analog voltages, and, depending on which is larger, generate an event output, drive a pin high or low, or fire an interrupt. One of the voltages can be the internal reference (0-series) an internal reference scaled by an 8-bit DAC (everything else). This library, written by @MCUDude, provides a simple wrapper around the analog comparator(s) which makes their configuration easier and resulting code more readable (also easier on the wrists - less stuff to type in all caps) than manually configuring registers, while exposing nearly the full featureset of the analog comparators on these parts. Do note does not support the Window Comparator option for the parts with 3 comparators; There doesn't exactly seem to be a lot of demand for that one, though.
This library is also included in DxCore and MegaCoreX, covering all modern AVRs with comparator hardware. Written by @MCUDude.
Comparator library documentation
For more information on resetting from software, using the Watchdog Timer, the causes of unexpected resets and how to prevent them, and generally all things reset-related, see the Reset Guide
It is often useful to identify what options are selected on the menus from within the sketch; this is particularly useful for verifying that you have selected the options you wrote the sketch for when opened later by yourself or someone who you shared it with. Or, you can use these, combined with #if macros to select the appropriate code depending on the part or options at hand.
There are a great number of #defines provided to get information on the hardware in use in order to write portable and flexible code in your sketch or particularly liberary code.
A new version of Optiboot (Optiboot_x) now runs on the tinyAVR 0-series, 1-series and 2-series chips. It's under 512 bytes, and works on all parts supported by this core allowing for a convenient workflow with the same serial connections used for both uploading code and debugging (like a normal Arduino Pro Mini) - except for the detail about not having autoreset unless you disable UPDI (except for the 20 and 24-pin 2-series parts which can put reset on PB4 instead), which is a bit of a bummer.
To use the serial bootloader, select a board definition with (optiboot) after it (note - this might be cut off due to the width of the menu; the second set of board definitions are the optiboot ones). The 2-series Optiboot definitions and the 0/1-series Optiboot definitions are separate entries in the board menu.
See the Optiboot referencefor more information.
These are being ported from DxCore as time permits. Many of them are identical on the two cores.
The API reference for the analog-related functionality that is included in this core beyond the standard Arduino API.
The API reference for the digital I/O-related functionality that is included in this core beyond the standard Arduino API, as well as a few digital I/O related features that exist in the hardware which we provide no wrapper around.
Includes a list of all interrupt vectors that can be used, how the flags are cleared (not a substitute for the datasheet - just a very quick reminder), which parts each vector exists on, and and what parts of the core, if any, make use of a vector. It also has general guidance and warnings relating to interrupts their handling, including estimates of real-world interrupt response times.
The USARTs (Serial) have some additional features not seen on the official cores.
Serial UPDI is our recommended tool for UPDI programming.
Supported clock sources and considerations for the use thereof.
Manufacturer specs for speed at various voltages, and some discussion of BOD thresholds.
The core feature defines are used by megaTinyCore and other cores I maintain as well. This also documents what constant values are defined by the core for version identification, testing for features, and dealing with compatibility problems.
Export compiled binary generates both assembly listings and memory maps, in addition to the hex file. The options selected are encoded in the name of the file to help prevent confusion, and make it easy to compare two configurations when you are surprised by the differences between them.
The sources of reset, and how to handle reset cause flags to ensure clean resets and proper functioning in adcverse events. Must read for production systems
The installation and operation of the Optiboot bootloader (for uploading over straight serial (not SerialUPDI)) is described here. Not recommended except on the 20/24-pin 2-series (since they have the alt reset pin) or for special use cases that demand it.
These guides are older, some are still relevant
This contains some of the information that would go into Ref_Timers like DxCore has.
This has been recently updated and will likely be turned into a Ref_TCA0.
This document describes how (on the 0 and 1 series only) the timer can be taken over and reconfigured, with particular attention to free running mode. The 2-series ADC is different, and it would require changes to reflect those differences.
- Tools -> Chip - sets the specific part within a selected family to compile for and upload to.
- Tools -> Clock - sets the clock speed. You must burn bootloader after changing between 16/8/4/1MHz and 20/10/5MHz to apply the changes (ie, changing from 20MHz to 10MHz does not require burning bootloader, changing from 20MHz to 16MHz does). A virgin chip will be set to use the 20MHz internal oscillator as its base clock source, so 20/10/5MHz clock speed options should work without an initial "burn bootloader" - though we still recommend it to ensure that all other fuses are set to the values you expect.
- Tools -> Retain EEPROM - determines whether to save EEPROM when uploading a new sketch. You must burn bootloader after changing this to apply the changes. This option is not available on Optiboot board definitions - programming through the bootloader does not execute a chip erase function.
- Tools -> B.O.D. Voltage - If Brown Out Detection is enabled, when Vcc falls below this voltage, the chip will be held in reset. You must burn bootloader after changing this to apply the changes. See the BOD configuration options section above for more information.
- Tools -> B.O.D. Mode when Active/Sleeping - Determines the brown-out detection mode in active and sleep modes. You must burn bootloader after changing this to apply the changes. See the BOD configuration options section above for more information.
- Tools -> UPDI/Reset pin (this menu is not available for 8 or 14-pin, non-optiboot parts, as an incorrect selection will brick your board if you don't have an HV UPDI programmer. If you do, the lines that could be uncommented to enable it are in the boards.txt)
- If set to UPDI, the pin will be left as the UPDI pin, there will be no hardware reset pin. If using Optiboot, to enter the bootloader, disconnect and reconnect power to the part or execute a software reset - either way, upload within 8 seconds.
- If set to Reset, the pin will be configured to act as reset, like a classic AVR, but UPDI programming will no longer work - you must use an HV programmer if you wish to reprogram via UPDI - if the pin is set to reset, if using Optiboot, the version of the bootloader used will jump straight to the application after a power-on reset, and will only enter the bootloader if reset by software reset or via the reset pin. The bootloader will also only wait 1 second for a sketch (ie, it behaves like optiboot does on classic AVR microcontrollers), instead of 8. If not using a bootloader, further programming requires an HV programmer; this option is not available on non-optiboot boards without modifying boards.txt as noted above.
- If it is set to I/O, the pin will act as a normal I/O pin with incredibly weak pin drivers - don't expect it to be able to source or sink more than 0.5mA when set output. If using Optiboot, the bootloader will behave in the same way as when the pin is left as UPDI. To reprogram using an HV programmer, you must use the Power Cycle High Voltage (PCHV) procedure. Consult the documentation for your HV programmer for more information. This option is not available on non-optiboot boards without modifying boards.txt as noted above.
- On the 2-series 20 and 24-pin part, an additional options is available, and the default when using Optiboot with those parts: Alternate Reset; with this option selected the UPDI pin retains it's UPDI functionality, but the PIN_PB4 ceases to be an I/O pin, and instead acts like an external RESET pin! In light of the continued scarcity of HV UPDI programmers within the hobbyist community. This option will result in an error message if bootloading a 0/1-series is attempte.
- Tools -> Startup Time - This is the time between reset (from any cause) and the start of code execution. We default to 8ms and recommend using that unless you have a reason not to - that default option is generally fine... In rare cases (such as particularly slow rising power supplies when BOD is not enabled, such that it needs to wait longer than the usual 8ms to have a voltage high enough to function reliably at, or conversely, when the power supply is known to be fast rising (or BOD is in use) and you have need to respond almost instantly after a reset)
Tools -> Voltage Baud Correction - If you are using the internal oscillator and reaaaaally want the UART baud rates to be as close to the target as possible you can set this to the voltage closer to your operating voltage, and it will use the factory programmed internal oscillator error values. Under normal operation, this just wastes flash and is not needed. That is why it now (as of 2.3.0) defaults to Ignore. Removed from 2.5.0- Tools ->
printf()implementation - The default option can be swapped for a lighter weight version that omits most functionality to save a tiny amount of flash, or for a full implementation (which allows printing floats with it) at the cost of about 1k extra. Note that if non-default options are selected, the implementation is always included in the binary, and will take space even if not called. This applies to everywhere that format strings are used, including Serial.printf(). - Tools -> attachInterrupt Mode - Choose from 3 options - the new, enabled on all pins always (like the old one), Manual, or the old implementation in case of regressions in the new implementation. When in Manual mode, You must call
attachPortAEnable()(replace A with the letter of the port) before attaching the interrupt. This allows attachInterrupt to be used without precluding any use of a manually defined interrupt (which is always much faster to respond. Basically any time you "attach" an interrupt, the performance is much worse. ) - Tools -> Wire Mode - In the past, you have only had the option of using Wire as a master, or a slave. Now the same interface can be used for both at the same time, either on the same pins, or in dual mode. To use simultaneous master or slave, or to enable a second Wire interface, the approipriate option must be selected from tools -> Wire Mode.
- Tools -> millis()/micros() - If set to enable (default), millis(), micros() and pulseInLong() will be available. If set to disable, these will not be available, Serial methods which take a timeout as an argument will not have an accurate timeout (though the actual time will be proportional to the timeout supplied); delay will still work. Disabling millis() and micros() saves flash, and eliminates the millis interrupt every 1-2ms; this is especially useful on the 8-pin parts which are extremely limited in flash. Depending on the part, options to force millis/micros onto specific timers are available. A #error will be shown upon compile if a specific timer is chosen but that timer does not exist on the part in question (as the 0-series parts have fewer timers, but run from the same variant). If RTC is selected, micros() and pulseInLong() will not be available - only millis() will be.
- Tools -> UART for Bootloader - If using Optiboot bootloader, select which set of pins you want to use for serial uploads. After making a selection, you must connect a UPDI programmer and do tools -> Burn Bootloader to upload the correct bootloader for the selected option.
If you are manually manipulating registers controlling a peripheral, you should not count on the behavior of API functions that relate to the same peripheral, nor should you assume that calling said API functions will not adversely impact the rest of your application. For example, if you "take over" TCA0, you should not expect that using analogWrite() - except on the two pins on the 20/24-pin parts controlled by TCD0 - will work for generating PWM; indeed you should expect that it will break whatever you are doing with TCA0.
Earlier versions of megaTinyCore enabled the internal pullup resistors on the I2C pins. This is no longer done; they are miles away from being strong enough to meet the I2C specifications - it was decided that it is preferably for it to fail consistently without external ones than to work under simple conditions with the internal ones, yet fail under more demanding ones (more devices, longer wires, etc).
While we generally make an effort to emulate the official Arduino core, there are a few cases that were investigated, but we came to the conclusion that the compatibility would not be worth the price. The following is a (hopefully nearly complete) list of these cases.
The official core for the (similar) megaAVR 0-series parts, which this was based on, fiddles with the interrupt priority (bet you didn't know that!) in ways that are of dubious safety towards other code. megaTinyCore does not do this (in the process saving several hundred bytes of flash, and fixing at least one serious bug which could result in hangs if serial was used in ways that everyone tells you not to use it). Writing to Serial when it's buffer is full, or calling Serial.flush() with interrupts disabled, or during another ISR (which you really shouldn't do) will behave as it does on classic AVRs, and simply block, manually calling the transmit handlers, until there is space in the buffer for all of the data waiting to be written, or the buffer is empty (for flush()).
This is deprecated on the official core, and is and always has been a dreadful misfeature. Dropped as of 2.3.0.
On official cores, and most third party ones, the digitalRead() function turns off PWM when called on a pin. This behavior is not documented by the Arduino reference. This interferes with certain optimizations, makes digitalRead() take at least twice as long as it needs to - and generally makes little sense. Why should a "read" operation change the thing it's called on? We have a function that alters the pin it's called on: digitalWrite(). There does not seem to be a logically coherent reason for this - and insofar as Arduino is supposed to be an educational platform it makes simple demonstrations of what PWM is non-trivial (imagine setting a pin to output PWM, and then looking at the output by repeatedly reading the pin). See also the above section on PWM using TCD0.
Like the official "megaavr" core, calling digitalWrite() on a pin currently set INPUT will enable or disable the pullups as appropriate. Additionally, as of 2.2.0, megaTinyCore fixes two bugs in this "classic emulation". On a classic core, digitalWrite() on an INPUT would also write to the port output register - thus, if one subsequently called pinMode(pin,OUTPUT), the pin would immediately output that level. This behavior is not emulated in the official core, and there is a considerable amount of code in the wild which depends on it. digitalWrite() now replicates that behavior. digitalWrite() also supports "CHANGE" as an option; on the official core, this will turn the pullup on, regardless of which state the pin was previously in, instead of toggling the state of it. The state of the pullup is now set to match the value that the port output register was just set to.
Similarly, using pinMode() to set a pin to INPUT or INPUT_PULLUP will now also set the port output register. warning There are a few cases where this is problematic due to silicon bugs in available hardware (most notably configuring I2C pin - where one may well want the pullups on (not that they are sufficient to meet the I2C requirements), but you must not have the output register set high. The Wire.h library works around this. The USART in Open Drain mode is another case)
Please see the above PWM feature description if using PWM on those pins and also using digitalRead() or direct port writes on the same pins (PIN_PC0, and PIN_PC1).
On the official "megaavr" board package, TCA0 is configured for "single mode" as a three-channel 16-bit timer (used to output 8-bit PWM). megaTinyCore always configures it for "Split mode" to get additional PWM outputs. See the datasheets for more information on the capabilities of TCA0. See Taking over TCA0 for information on reconfiguring it. One downside to this is that the compare channels do not support buffering, so changing the duty cycle can cause a glitch lasting up to PWM cycle (generally under 1 ms).
0 is a count, so at 255, there are 256 steps, and 255 of those will generate PWM output - but since Arduino defines 0 as always off and 255 as always on, there are only 254 possible values that it will use. The result of this is that (I don't remember which) either analogWrite(pin,254) results in it being LOW 2/256's of the time, or analogWrite(pin,1) results in it being HIGH 2/256's of the time. On megaTinyCore, with 255 steps, 254 of which generate PWM, the hardware is configured to match the API, and this does not occur; as it happens, 255 also (mathematically) works out such that integer math gets exact results for millis timing with both 16 MHz derived and 20 MHz derived clock speeds (relevant when TCA0 is used for millis() timing). The same thing is done for TCD0 (though to 509, giving 510 steps - analogWrite() accounts for this - so that we can get the same output frequency while keeping the fastest synchronization prescaler for fastest synchronization between TCD0 and system clock domains).
On the official "megaavr" board package, as well as DxCore, the type B timers are used to generate 8-bit PWM (one pin per timer), there are very few circumstances where this could increase the number of usable PWM pins. These timers are just too scarce and valuable on these parts. Being minimally useful for PWM, in short supply, and highly desirable for other purposes, support for using them for PWM was removed in order to save space that would otherwise be used initializing these timers for PWM and handling them in analogWrite() et. al. If a Type B timer is used for millis(), it is configured in a radically different way than the official core does.
They return and expect uint8_t (byte) values, not enums like the official megaavr board package does. Like classic AVR cores, constants like LOW, HIGH, etc are simply #defined to appropriate values. The use of enums unfortunately broke many common Arduino programming idioms and existing code (granted, these idioms were poor programming practice - they're also incredibly widespread and convenient), increased flash usage, lowered performance, and made optimization more challenging. While the enum implementation made language design purists comfortable, and provided error checking for newbies - because you couldn't pass anything that wasn't a PinState to a digital I/O function, and would get that error checking if - as a newbie - you accidentally got careless. So, due to all the complaints, a compatibility layer was added to the official core, so all the old tricks would work again, it was just less performant. However, that got rid of what was probably the most compelling benefit, the fact that it did generate an error for new users to train them away from common Arduino practices like passing 1 or 0 to digitalWrite, if(digitalRead(pin)) and the like. The choice of names of the enums also had the perverse effect of making PinMode(pin,OUTPUT), an obvious typo of pinMode(pin,OUTPUT) into valid syntax (comma operator turns pin,OUTPUT into OUTPUT, and it returns a new PinMode of value OUTPUT...) and does nothing with it, instead of a syntax error (It took me over an hour to find the extra capitalization. That evening, I converted the digital I/O functions to the old signatures and removed the enums). Anyway - the enums are not present here, and they never will be; this is the case with MegaCoreX and DxCore as well.
The earlier versions of the avr-gcc toolchain contained several issues relevant to these parts. Version 2.0.4 and later, when installed through Board Manager, will pull in the new toolchain package which corrects both of these issues (among other ones that nobody had noticed yet)
- Sometimes a sketch which is too big to fit will, instead of generating a message saying that, result in the error: 'relocation truncated to fit: R_AVR_13_PCREL against symbol tablejump2'.
- There is a bug in the
<avr/eeprom.h>library's eeprom_is_ready() macro - it uses names for registers from the XMEGA family of parts (under the hood, these chips actually have an XMEGA core!). Attempting to use that macro will generate a error stating that'NVM_STATUS' was not declared in this scope. This has been corrected in current compiler packages; if you get this error, update the official AVR board package, upgrade to Arduino 1.8.13, or install megaTinyCore using board manager.
There are two classes of significant low level architectural differences (aside from the vastly improved peripherals) - the improved instruction set, and the unified memory address space.
The classic AVR devices all use the venerable AVRe (ATtiny) or AVRe+ (ATmega) instruction set (AVRe+ differs from AVRe in that it has hardware multiplication and supports devices with more than 64k of flash). Modern AVR devices (with the exception of ones with minuscule flash and memory, such as the ATtiny10, which use the reduced core AVRrc) all use the latest iteration of the AVR instruction set, AVRxt. AVRxt has much in common with AVRxm (used in XMega parts) in terms of instruction timing - and in the few places where they differ, AVRxt is faster (SBIC, as well as LDD, and LD with predecrement, are all 1 clock slower on AVRxm vs AVRxt or AVRe), however AVRxt doesn't have the single-instruction-two-clock read-and-write instructions for memory access LAT, LAC, LAS, and XCH. The difference between subspecies of the AVR instruction set is unimportant for 99.9% of users - but if you happen to be working with hand-tuned assembly (or are using a library that does so, and are wondering why the timing is messed up), the changes are:
- Like AVRe+ and unlike AVRe (used in older tinyAVR), these do have the hardware multiplication.
- PUSH is 1 cycle vs 2 on classic AVR (POP is still 2)
- CBI and SBI are 1 cycle vs 2 on classic AVR
- LDS is 3 cycles vs 2 on classic AVR 😞 LD and LDD are - as always - two cycle instructions.
- RCALL and ICALL are 2 cycles vs 3 on classic AVR
- CALL is 3 cycles instead of 4 on classic AVR
- ST and STD is 1 cycle vs 2 on classic AVR (STS is still 2 - as any two word instruction must be)
As you can see, everything that involves writing to the SRAM is faster now; it would appear that any time it is writing to a location based on one of the pointer registers or the stack pointer, it's a single cycle. All the other improvements except CBI and SBI can be viewed as a consequence of that. Of course the variants of call are faster, they have to put the return address into the stack. I can't say I've ever felt like LAT, LAC, or LAS would be terribly useful as they are described in the instruction set manual - those take a register and the address pointed to by the Z register, and load the contents of the specified address, and toggle, set or clear in that memory address the bits that were set to begin with in the register. If that worked on special function registers, it would be a very useful instruction (taking PERIPHERAL.REGISTER |= SOME_BIT_bm; from a 5 clock, non-atomic operation to a 2 clock atomic one! But it says they only work on SRAM... so not as much of a loss. XCH is more obviously useful than the others, but all 4 of them come with the need to set up the Z register... which in many cases would take long enough that it wouldn't be a notable improvement.
Note that the improvement to PUSH can make interrupts respond significantly faster (since they have to push the contents of registers onto the stack at the beginning of the ISR), though the corresponding POP's at the end aren't any faster. The change with ST impacted tinyNeoPixel. Prior to my realizing this, the library worked on SK6812 LEDs (which happened to be what I tested with) at 16/20 MHz, but not real WS2812's. However, once I discovered this, I was able to leverage it to use a single tinyNeoPixel library instead of a different one for each port like was needed with ATTinyCore (for 8 MHz, they need to use the single cycle OUT on classic AVRs to meet timing requirements, the two cycle ST was just too slow; hence the port had to be known at compile time, or there must be one copy of the routine for each port, an extravagance that the ATtiny parts cannot afford. But with single cycle ST, that issue vanished).
Oh, and one other instruction it doesn't have that (some) AVRxm parts have: The hardware DES encryption instruction - an instruction which is most effective at marking AVRxm as, ah, back from the time when DES was a big deal.
On all modern AVRs with up to 48k of flash, both the flash and ram reside in the same address space - On tinyAVRs, the program memory starts at 0x8000, while on megaAVR 0-series, it starts at 0x4000 to leave room for the 48k of flash that they can have, and on the Dx-series parts with up to 32k of flash, they have the same layout as the tinyAVRs, while Dx-series parts with 64k or 128k of flash have a 32k section of flash mapped at any given time (how to make sure variables go into this memory mapped flash has been described elsewhere in this document). There is another big and fundamental change to the layout of the address space as well: the registers are organized by peripheral. PORTA is assigned 0x400 to 0x41F. PORTB is the next 32 bytes, and so on - and the address space is far sparser - all the peripherals have multiple "reserved" registers that may or may not get functions added in the future. And each instance of a peripheral on a part that has multiple of them has the same layout. You can, say, pass a pointer to a TCB around without the functions that get it knowing which TCB they'll get, and then access the TCB registers through it. On classic AVRs the names of the registers were consistent, but their locations were all over the place, packed much more tightly, so that sort of trick isn't possible. This also means that the EEPROM (and USERROW) are part of this unified address space (on classic AVRs, reading was accomplished through special function registers, and was far more awkward. So is the full signature space. )
The lowest 64 registers are special - you can read or write them with the IN or OUT instructions (hence, "I/O space") in a single clock cycle, without setting up a pointer to them as you would need to with ST or LD. The 32 "Low I/O registers" additionally have bit-level access instructions CBI and SBI to clear and set bits, and SBIC/SBIS to skip the next instruction if a certain bit is set or cleared. On all AVRxt parts released so far, the low I/O registers are used only for the VPORTs up to VPORTG (meaning VPORTG.OUT |= 1<<n (where n is compile-time known and constant) is 1 clock cycle and atomic, while VPORTG.OUT = 1<<n is two - first to put the value to be stored into a register, and secondly to write it with an out instruction. The GPIOR0-3 registers occupying the last 4 bytes in the low I/O space (those are user-defined registers to use as you choose, megaTinyCore's version of Optiboot stashes the reset cause in GPIOR0 before resetting reset cause (so it can honor bootloader entry conditiosn on next reset) and jumping to app; No other part of this core touches those registers, and we only set GPIOR0 (and only when using optiboot), never read it. So all can be used freely, as long as you remember to clear GPIOR0 if using Optiboot). On parts which do not have 7 ports, for example tinyAVR parts with only ports A, B, and C, there's a VPORTA, VPORTB and VPORTC taking up the first 12 locations in the low I/O space. And then the rest are "reserved" up until the GPIO registers.
The 32 "high I/O registers" are used even less - they only get the the stack pointer, RAMPZ on the 128k DA/DB parts, SREG, and CCP (Configuration Change Protection - where _PROTECTED_WRITE() does it's magic to let you write to protected registers. That's all - 5 out of 32 registers are used, the rest are "reserved". On classic AVRs, they took frequently used registers from all over the register space and put them there, since they can be read and written faster and more efficiently. It is somewhat disappointing that they didn't mirror some of the most used peripheral registers into the high I/O space. (Interrupt flags? Serial/SPI/I2C data?) This has the consequence of making some register access operations both larger and slower than the would be on classic AVRs which took advantage of the I/O space. It is not clear to me how much of an impact this ends up having on sketch size, nor why it was done. I'm sure it was discussed, and they had good reasons not to.... but it seems like kind of a waste.
megaTinyCore itself is released under the LGPL 2.1. It may be used, modified, and distributed freely, and it may be used as part of an application which, itself, is not open source (though any modifications to these libraries must be released under the LGPL as well). Unlike LGPLv3, if this is used in a commercial product, you are not required to provide means for user to update it.
The megaTinyCore hardware package (and by extension this repository) contains megaTinyCore as well as libraries, bootloaders, and tools. These are released under the same license, unless specified otherwise. For example, tinyNeoPixel and tinyNeoPixel_Static, being based on Adafruit's library, is released under GPLv3, as described in the LICENSE.md in those subfolders and within the body of the library files themselves.
The pyupdi-style serial uploader in megaavr/tools is built on pymcuprog from Microchip, which is not open source has now been released under the open source MIT license!
Any third party tools or libraries installed on behalf of megaTinyCore when installed via board manager (including but not limited to, for example, avr-gcc and avrdude) are covered by different licenses as described in their license files.