[Bug] Uneven battery drain in RX300

Box Model:
RX300

Coil setup:
TFV8 w/ 10 Coil @ 0.13ohm.

I'm just writing to report a possible bug in the latest myevic firmware.

I have been using MyEvic on my RX series mods for a while now, and have never noticed any problems, and infact have always enjoyed this firmware so much better than stock.
So naturally, when I received my RX300, the first thing I did was update it to MyEvic.

After a couple of hours though, I begun to notice something strange.

The battery percentage on the main screen was draining much quicker than it should be, and whilst I know that the battery percentage/icon on the main screen just shows you the lowest volts out of the set of batteries, it was decreasing far too quickly.
Checking the volts in the BVO setting, I noticed that B2 was always at least .2v lower than the other 3 batteries.
So, noticing this, I swapped out the batteries for different ones that I'd just taken off charge. As usual, BVO reported that they were all at around 4.2v.
Again however, after just a couple of hours of vaping, B2 was hovering .2v lower than the other 3, so whilst B1, B3 & B4 would be at 4v, B2 is at about 3.8.

After testing this problem some more, with different married & unmarried batteries, I always noticed the same pattern emerged. So, I checked my mod. It being brand new, I didn't notice any problems with the connections, so in my defeat, I reinstalled the latest stock RX300 firmware.

Due to the stock firmware showing me the charge levels of all 4 batteries on the front screen, I was able to keep my eye on the batteries over the next couple of hours. Unfortunately, I noticed that all 4 batteries were draining evenly whilst using the stock firmware, which is of course good, but bad in the sense that it appears there was something wrong with MyEvic.

I will note that whilst vaping, I was at roughly 95W with a preheat of 110% for 1 second, so it's not as if I was vaping at incredibly high wattages which would drain my batteries incredibly fast.

I'm just wondering if there could be a fix for this bug? Or even if anybody else has suffered with the same thing?

I can provide any information you need and will help out the best I can. I hate reporting bugs, but if it will better improve MyEvic, then it is totally worth it.

[fOmey]

I experienced a similar situation on my RX2/3, I was actually in the process of trying to make the battery voltage readings more accurate.

Unfortunately tho my RX2/3 died yesterday.. very poor design choices on wismecs behalf on this device but I digress..

I noticed the exact same thing with my RX2/3, as the battery drained the voltage readings became less and less accurate, I had tested the battery voltages throughout the battery discharge and even tho they were being reported .2, .3, or even .10 lower than each other they were indeed being discharged evenly.

This is the ReadBatteryVoltage() function for the RX2/3:

VbatSample1 = 125 * ( VbatSample1 >> 7 ) / 100;
VbatSample2 = 139 * ( VbatSample2 >> 4 ) / 624;
VbatSample3 =   3 * ( VbatSample3 >> 4 ) >> 3;

BattVolts[0] = VbatSample1;

if ( VbatSample2 <= VbatSample1 + 20 )
	BattVolts[1] = 0;
else
	BattVolts[1] = VbatSample2 - BattVolts[0];

if ( VbatSample3 <= VbatSample2 + 20 )
	BattVolts[2] = 0;
else
    BattVolts[2] = VbatSample3 - BattVolts[0] - BattVolts[1];

Not sure how code savy you are, but there has got to be a better way to calculate battery voltage then the current solution.. Because were subtracting voltages from one another they cant truly be accurate,

I actually got very accurate readings at one point while testing but it opened up another issue regarding 2 or 3 battery mode at least on the RX2/3.. the problem I discovered was that each sample will return a value regardless how many batteries you have in the device at any given time, I was in the process of sorting through the values to attempt to map out certain battery configurations.. but as I mention my RX2/3 had died and I wont be able to continue till I find a replacement device.

[MrScaryZ]

I have exactly the same problem with the RX 300 it is draining batteries unevenly and this has been checked on a OPUS 3100 V 2-2 and it occurs with both LG HE4 and Samsung 25R's in fact it drained battery #4 to 2.5 volts several times

…

On Thu, Feb 23, 2017 at 2:39 PM, fOmey ***@***.***> wrote: I experienced a similar situation on my RX2/3, I was actually in the process of trying to make the battery voltage readings more accurate. Unfortunately tho my RX2/3 died yesterday.. very poor design choices on wismecs behalf on this device but I digress.. I noticed the exact same thing with my RX2/3, as the battery drained the voltage readings became less and less accurate, I had tested the battery voltages throughout the battery discharge and even tho they were being reported .2, .3, or even .10 lower than each other they were indeed being discharged evenly. This is the ReadBatteryVoltage() function for the RX2/3: ` VbatSample1 = 125 * ( VbatSample1 >> 7 ) / 100; VbatSample2 = 139 * ( VbatSample2 >> 4 ) / 624; VbatSample3 = 3 * ( VbatSample3 >> 4 ) >> 3; BattVolts[0] = VbatSample1; if ( VbatSample2 <= VbatSample1 + 20 ) BattVolts[1] = 0; else BattVolts[1] = VbatSample2 - BattVolts[0]; if ( VbatSample3 <= VbatSample2 + 20 ) BattVolts[2] = 0; else BattVolts[2] = VbatSample3 - BattVolts[0] - BattVolts[1]; ` Not sure how code savy you are, but there has got to be a better way to calculate battery voltage then the current solution.. Because were subtracting voltages from one another they cant truly be accurate, I actually got very accurate readings at one point while testing but it opened up another issue regarding 2 or 3 battery mode at least on the RX2/3.. the problem I discovered was that each sample will return a value regardless how many batteries you have in the device at any given time, I was in the process of sorting through the values to attempt to map out certain battery configurations.. but as I mention my RX2/3 had died and I wont be able to continue till I find a replacement device. — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#291 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AX-SozaEGwu0SaUd4d6iHr_Ejytw5tH3ks5rfe5ogaJpZM4MKdDx> .

-- Randy Wheeler

[lostvoid]

I've got the same issue on my 300. I've also noticed that there is an issue with the device in standby mode where it will drain B2 to 0 volts and kill the battery.

[docdeath]

after reading the above i checked my rx300 and found same on he4,s and 30q and 25r, only way to stop this was to change batts to gen it slows it down but still a problem

[USA-RedDragon]

Can confirm as well

[danielpublic]

Not sure yet if I can confirm this on my rx300, but testing Game to click menu & multiple battery voltage stats #285 I noticed one batteries V were really really low. Had stock latest firmware moments before this.

Edit: 0.08v on bottom right battery. Stock firmware reports everything is all swell and dandy.
Physically measuring the batteries individual voltages confirms stock firmware observation.

So it seems that this is a genuine bug which effects a fair few of us RX300 users, and isn't necessarily down to any brand of battery or way of using the device.

From the evidence given above, it's the firmware falsely reporting the battery voltage levels and making it so that 1 of the 4 is draining much quicker. Or at least, the firmware is responsible for the over-draining of 1 out of the 4 batteries.

Am I right in saying that?

If so, is there any way to fix this? As @fOmey suggested, there must be a better way to calculate the voltages, however I'm at a complete loss due to my lack of coding skills. I just hope that at least with myself bringing attention to it, and others reporting that they too have problems, that it can somehow be fixed.

[fOmey]

Can you guys please check your battery voltage with a multimeter, voltage checker, charger or what ever and figure out if the battery voltage is just being reported with incorrect voltages or if the battery's are indeed being discharged unbalanced.

My RX2/3 was reporting unbalanced voltages, although my battery's were discharging at the same rate.. so the firmware was just reporting the incorrect voltages...

Unfortunately I do not own a RX300, also my RX2/3 died recently.. I wont be able to continue development until I get my hands on a new device.

Hopefully @ClockSelect can chime in, I'm sure he would have an idea of the best way to resolve this.

[USA-RedDragon]

After I noticed battery drain on one battery I immediately switched back to stock firmware where voltage persisted to be uneven.

…

On Wed, Mar 8, 2017, 3:59 PM fOmey ***@***.***> wrote: Can you guys please check your battery voltage with a multimeter, voltage checker, charger or what ever and figure out if the battery voltage is just being reported with incorrect voltages or if the battery's are indeed being discharged unbalanced. My RX2/3 was reporting unbalanced voltages, although my battery's were discharging at the same rate.. so the firmware was just reporting the incorrect voltages... Unfortunately I do not own a RX300, also my RX2/3 died recently.. I wont be able to continue development until I get my hands on a new device. Hopefully @ClockSelect <https://github.com/ClockSelect> can chime in, I'm sure he would have an idea of the best way to resolve this. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#291 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AMcndwfOwYtaeC_d2nKBk9_U77LwnEZjks5rjySrgaJpZM4MKdDx> .

[shurizzle]

Same here with a RX2/3

[danielpublic]

The rx300 threw an 'check battery' at me, put the batteries in my bt-c3100. It displayed: 4.08v, 4.10v, 3.13v, 4.09v. Can post an pic later, since my phone doesn't seem to cooperate. Charging batteries atm.

[MrScaryZ]

Has their been any progress on this? I had to revert back again to the stock firmware. Uneven drain is one thing but draining a battery to below Liion safe specs is another.. now it has happened with HE4's HG2's VTC5a's and 25r's

…

On Fri, Mar 10, 2017 at 4:23 AM, danielpublic ***@***.***> wrote: The rx300 threw an 'check battery' at me, put the batteries in my bt-c3100. It displayed: 4.08v, 4.10v, 3.13v, 4.09v. Can post an pic later, since my phone doesn't seem to cooperate. Charging batteries atm. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#291 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AX-So5b5TMgW_2fs-ua4qVAnxjKU4oPrks5rkSSagaJpZM4MKdDx> .

-- Randy Wheeler

Apologies for closing & reopening the thread, I was trying to sort out some pictures uploading. Heh. Eventually had to resort to uploading to Imgur due to them not uploading through Github.

Okay so, I've just reinstalled myevic onto my RX300 to test this out so you guys have more data on your hands. You'll have to give me a couple of hours, but I'll try and be a thorough as I can.

I've literally just this second reinstalled myevic and I'm about to pull 4 Samsung 30Qs off charge to put in the device, so I KNOW they are all at 4.20v.

After putting the batteries in, I set the BAT at 30Q and in the BVO I can see they're reading a little bit off kilter, which is fine.

http://imgur.com/kW2tvyI

I've effectively "zeroed" the batteries to reading at 4.20v, so they're all as equal as possible.

http://imgur.com/UwsjhCw

And I will be vaping at 95w with a 110% preheat for 0.8 seconds.

http://imgur.com/06rIZd6

I will report back in a couple of hours with the results!