-
Notifications
You must be signed in to change notification settings - Fork 0
/
pid&bed_mesh.cfg
108 lines (92 loc) · 2.33 KB
/
pid&bed_mesh.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
[gcode_macro MORNING_ROUTINE]
description: PID tune for extruder and bed, then bed level
gcode:
STOP_LED_EFFECTS
G28
NEOPIXEL_DISPLAY LED=my_led TYPE=bed_temp MODE=glow
G1 X190 Y185 Z20 F 3000
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(200)|float %}
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
PID_CALIBRATE HEATER=extruder TARGET={EXTRUDER_TEMP}
TURN_OFF_HEATERS
NEOPIXEL_DISPLAY LED=my_led TYPE=extruder_temp MODE=glow
G1 X190 Y185 Z20 F 3000
PID_CALIBRATE HEATER=heater_bed TARGET={BED_TEMP}
TURN_OFF_HEATERS
Z_TILT_ADJUST
BED_MESH_CALIBRATE
G28
#SAVE_CONFIG
[gcode_macro PID_EXTRUDER]
description: PID Tune for the Extruder
gcode:
STOP_LED_EFFECTS
G28
NEOPIXEL_DISPLAY LED=my_led TYPE=extruder_temp MODE=glow
G1 X200 Y10 Z120 F 3000
{% set TARGET_TEMP = params.TARGET_TEMP|default(200)|float %}
PID_CALIBRATE HEATER=extruder TARGET={TARGET_TEMP}
TURN_OFF_HEATERS
#PARK
#SAVE_CONFIG
[gcode_macro PID_BED]
description: PID Tune for the Bed
gcode:
STOP_LED_EFFECTS
G28
NEOPIXEL_DISPLAY LED=my_led TYPE=bed_temp MODE=glow
G1 X190 Y185 Z20 F 3000
{% set TARGET_TEMP = params.TARGET_TEMP|default(60)|float %}
PID_CALIBRATE HEATER=heater_bed TARGET={TARGET_TEMP}
TURN_OFF_HEATERS
#PARK
#SAVE_CONFIG
[gcode_macro BED_LEVEL]
gcode:
STOP_LED_EFFECTS
G28
NEOPIXEL_DISPLAY LED=my_led TYPE=printer_speed MODE=glow
Z_TILT_ADJUST
BED_MESH_CALIBRATE
G28
#SAVE_CONFIG
[gcode_macro Z_AXI_CALIBRATE]
gcode:
G28
PROBE_CALIBRATE
[gcode_macro SHAPER]
gcode:
STOP_LED_EFFECTS
G28
NEOPIXEL_DISPLAY LED=my_led TYPE=printer_speed MODE=glow
SHAPER_CALIBRATE
#SAVE_CONFIG
[gcode_macro Press_Advance_short]
gcode:
SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=1 ACCEL=500
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.005
[firmware_retraction]
retract_length: 1.0
retract_speed: 45
unretract_extra_length: 0
unretract_speed: 40
[gcode_macro M600]
gcode:
{% set X = params.X|default(25)|float %}
{% set Y = params.Y|default(30)|float %}
{% set Z = params.Z|default(20)|float %}
SAVE_GCODE_STATE NAME=M600_state
PAUSE
G91
G1 E-.8 F2700
G1 Z{Z}
G90
G1 X{X} Y{Y} F3000
G91
G1 E-50 F1000
RESTORE_GCODE_STATE NAME=M600_state
[gcode_macro ready]
gcode:
G28
Z_TILT_ADJUST
SCREWS_TILT_CALCULATE