Replies: 3 comments
-
Bonjour Boris, Questions intéressantes ;) C'est très simple, pour l'obfuscation que l'on pourrait traduire en francais par brouilage. L'idée est de chiffrer un minimum les données transmises par voie radio. C'est un algorithme de chiffrement offrant un niveau de sécurité faible, mais connu et utilisé depuis longtemps. Il est basé sur l'utilisation de l'opérateur logique XOR (ou exclusif), qui présente ici l'avantage d'être réversible. Bref, ca évite de transmettre les datas en claire. Et même s'il est facile à casser, on ne transmet pas non plus les codes de la réplique atomique. Donc, ca fait le boulot ici. Pour le transpondeur, on ne peux pas faire plus simple que sur ce firmware :) Imaginons que ta fréquence RX est 439,450 MHz et ta fréquence TX est 145,3625 MHz Il faut donc commencer par paramétrer TxODir (menu 07/66) à - (puisque la fréquence d'émission est en dessous de la fréquence de réception). Et il suffit ensuite de paramétrer TxOffs à 294,08750 MHz (menu 08/66). Je précise une chose importante : depuis TxOffs, tu peux saisir la fréquence de décalage depuis le clavier et pas uniquement en utilisant les flèches de direction haut et bas :) Et c'est tout. En complément, à noter que le mode Cross Band peut aider ici aussi. Dans ce mode, l'émission est toujours sur la fréquence du VFO A et écoute sur la fréquence du VFO B. 73' Armel F4HWN |
Beta Was this translation helpful? Give feedback.
-
Bonjour Armel Oui, j'ai lu le code, mais comprend pas vraiement le pourquoi. Le system est connu, le system en Effectivement, j'avais pas pense a l'offset. Je sais pas pourquoi, je pense qu'il etait limite a 10Mhz. J'ai vu une version logiciel (qui n'est pas chirp) ou on donne les 2 frequences. Je ne sais pas comment [...] VFO_Info_t [...] FREQ_Config_t *pRX; {...] FREQ_Config_t *pTX; [...] La fonction semble prevu dans les varaibles des VFOs, mais rien pour les memoires et lorsqu'on cherche le xxx->vfoA->pRX.frequency = freq; xxx->vfoA->pTX.frequency = freq; J'arrete ici mon message, encore une fois kilometrique. 73's |
Beta Was this translation helpful? Give feedback.
-
Mais nous sommes bien d'accord. Ce qui est clair, c'est que l'on peut effectivement se passer de ce brouillage. Et c'est une bonne chose, parce que c'est justement un bon moyen de récupérer de la mémoire si le besoin s'en fait sentir. Mais ce n'est pas vraiment le cas actuellement :) C'est comme la fonction AES que j'ai débranché suelement récemment. J'aime bien en avoir sous le coude si besoin, raison pour laquelle je maintiens ce brouillage pour l'instant. 73' Armel F4HWN. |
Beta Was this translation helpful? Give feedback.
-
Bonjour Armel
Encore un tres grand merci pour l'enorme travail (nocturne ;-) sur votre firmware.
J'ai une question, je lis et essai de comprendre mais ne trouve pas de reponce.
Pourquoi dans la section aircopy on fait un 'Obfuscation' ?
Je ne comprends pas le pourquoi du comment de cette fonction.
Autre question, j'ai un peu cherche (oui je sais RTFM) pour faire des memoires en cross-bande.
Typiquement du relais VHF/UHF (ou satelitte par exemple). Mais je trouve pas de solution.
J'ai regarde dans Chirp mais rien non plus. J'ai merdouiller quelque part???
Merci de m'avoir lu
Bonne journee
73's
Boris
Beta Was this translation helpful? Give feedback.
All reactions