compile-all-inverters.yml

# This is the name of the workflow, visible on GitHub UI.
name: Compile All Inverters

# Here we tell GitHub when to run the workflow.
on:
  # The workflow is run when a commit is pushed or for a
  # Pull Request.
  - push
  - pull_request

# This is the list of jobs that will be run concurrently.
jobs:
  # This pre-job is run to skip workflows in case a workflow is already run, i.e. because the workflow is triggered by both push and pull_request
  skip-duplicate-actions:
    runs-on: ubuntu-latest
    # Map a step output to a job output
    outputs:
      should_skip: ${{ steps.skip_check.outputs.should_skip }}
    steps:
      - id: skip_check
        uses: fkirc/skip-duplicate-actions@v5
        with:
          # All of these options are optional, so you can remove them if you are happy with the defaults
          concurrent_skipping: 'never'
          skip_after_successful_duplicate: 'true'
          do_not_skip: '["pull_request", "workflow_dispatch", "schedule"]'

  # Since we use a build matrix, the actual number of jobs
  # started depends on how many configurations the matrix
  # will produce.

  # This is the name of the job.
  build-inverters:
    needs: skip-duplicate-actions
    if: needs.skip-duplicate-actions.outputs.should_skip != 'true'

    # Here we tell GitHub that the jobs must be determined
    # dynamically depending on a matrix configuration.
    strategy:
      # The matrix will produce one job for each combination of parameters.
      matrix:
        # This is the development board hardware for which the code will be compiled.
        # FBQN stands for "fully qualified board name", and is used by Arduino to define the hardware to compile for.
        fqbn:
          - esp32:esp32:esp32
          # further ESP32 chips
          #- esp32:esp32:esp32c3
          #- esp32:esp32:esp32c2
          #- esp32:esp32:esp32c6
          #- esp32:esp32:esp32h2
          #- esp32:esp32:esp32s3
        # These are the batteries for which the code will be compiled.
        battery:
          - NISSAN_LEAF_BATTERY
        # These are the emulated inverter communication protocols for which the code will be compiled.
        inverter:
          - AFORE_CAN
          - BYD_CAN
          - BYD_KOSTAL_RS485
          - BYD_MODBUS
          - FOXESS_CAN
          - PYLON_CAN
          - PYLON_LV_CAN
          - SCHNEIDER_CAN
          - SMA_BYD_H_CAN
          - SMA_BYD_HVS_CAN
          - SMA_LV_CAN
          - SMA_TRIPOWER_CAN
          - SOFAR_CAN
          - SOLAX_CAN
          - SERIAL_LINK_TRANSMITTER
          - NISSANLEAF_CHARGER # Last element is not an inverter, but good to also test if the charger compiles
        # These are the supported hardware platforms for which the code will be compiled.
        hardware:
          - HW_LILYGO

    # This is the platform GitHub will use to run our workflow.
    runs-on: ubuntu-latest

    # This is the list of steps this job will run.
    steps:
      # First we clone the repo using the `checkout` action.
      - name: Checkout
        uses: actions/checkout@v4
      
      # Copy USER_SECRETS.TEMPLATE.h to USER_SECRETS.h
      - name: Copy USER_SECRETS.TEMPLATE.h to USER_SECRETS.h
        run: cp ./Software/USER_SECRETS.TEMPLATE.h ./Software/USER_SECRETS.h

      # We use the `arduino/setup-arduino-cli` action to install and
      # configure the Arduino CLI on the system.
      - name: Setup Arduino CLI
        uses: arduino/setup-arduino-cli@v2

      # We then install the platform.
      - name: Install platform
        run: |
          arduino-cli core update-index
          arduino-cli core install esp32:esp32

      # Finally, we compile the sketch, using the FQBN that was set
      # in the build matrix, and using build flags to define the
      # battery and inverter set in the build matrix.
      - name: Compile Sketch
        run: arduino-cli compile --fqbn ${{ matrix.fqbn }} --build-property "build.extra_flags=-Wall -DESP32 -D${{ matrix.battery}} -D${{ matrix.inverter}} -D${{ matrix.hardware}}" ./Software