-
Notifications
You must be signed in to change notification settings - Fork 3.9k
/
xfsdist_example.txt
155 lines (121 loc) · 6.77 KB
/
xfsdist_example.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
Demonstrations of xfsdist, the Linux eBPF/bcc version.
xfsdist traces XFS reads, writes, opens, and fsyncs, and summarizes their
latency as a power-of-2 histogram. For example:
# ./xfsdist
Tracing XFS operation latency... Hit Ctrl-C to end.
^C
operation = 'read'
usecs : count distribution
0 -> 1 : 0 | |
2 -> 3 : 362 | |
4 -> 7 : 807 |* |
8 -> 15 : 20686 |****************************************|
16 -> 31 : 512 | |
32 -> 63 : 4 | |
64 -> 127 : 2744 |***** |
128 -> 255 : 7127 |************* |
256 -> 511 : 2483 |**** |
512 -> 1023 : 1281 |** |
1024 -> 2047 : 39 | |
2048 -> 4095 : 5 | |
4096 -> 8191 : 1 | |
operation = 'open'
usecs : count distribution
0 -> 1 : 0 | |
2 -> 3 : 3 |****************************************|
This output shows a bi-modal distribution for read latency, with a faster
mode of 20,686 reads that took between 8 and 15 microseconds, and a slower
mode of over 10,000 reads that took between 64 and 1023 microseconds. It's
likely that the faster mode was a hit from the in-memory file system cache,
and the slower mode is a read from a storage device (disk).
This "latency" is measured from when the operation was issued from the VFS
interface to the file system, to when it completed. This spans everything:
block device I/O (disk I/O), file system CPU cycles, file system locks, run
queue latency, etc. This is a better measure of the latency suffered by
applications reading from the file system than measuring this down at the
block device interface.
Note that this only traces the common file system operations previously
listed: other file system operations (eg, inode operations including
getattr()) are not traced.
An optional interval and a count can be provided, as well as -m to show the
distributions in milliseconds. For example:
# ./xfsdist -m 1 5
Tracing XFS operation latency... Hit Ctrl-C to end.
10:14:15:
operation = 'read'
msecs : count distribution
0 -> 1 : 1366 |****************************************|
2 -> 3 : 86 |** |
4 -> 7 : 95 |** |
8 -> 15 : 132 |*** |
16 -> 31 : 72 |** |
operation = 'write'
msecs : count distribution
0 -> 1 : 685 |****************************************|
10:14:16:
operation = 'read'
msecs : count distribution
0 -> 1 : 984 |****************************************|
2 -> 3 : 66 |** |
4 -> 7 : 67 |** |
8 -> 15 : 104 |**** |
16 -> 31 : 70 |** |
32 -> 63 : 12 | |
operation = 'write'
msecs : count distribution
0 -> 1 : 536 |****************************************|
10:14:17:
operation = 'read'
msecs : count distribution
0 -> 1 : 1262 |****************************************|
2 -> 3 : 75 |** |
4 -> 7 : 80 |** |
8 -> 15 : 119 |*** |
16 -> 31 : 75 |** |
32 -> 63 : 3 | |
operation = 'write'
msecs : count distribution
0 -> 1 : 639 |****************************************|
10:14:18:
operation = 'read'
msecs : count distribution
0 -> 1 : 1070 |****************************************|
2 -> 3 : 58 |** |
4 -> 7 : 74 |** |
8 -> 15 : 140 |***** |
16 -> 31 : 60 |** |
32 -> 63 : 5 | |
operation = 'write'
msecs : count distribution
0 -> 1 : 556 |****************************************|
10:14:19:
operation = 'read'
msecs : count distribution
0 -> 1 : 1176 |****************************************|
2 -> 3 : 53 |* |
4 -> 7 : 94 |*** |
8 -> 15 : 112 |*** |
16 -> 31 : 77 |** |
32 -> 63 : 3 | |
operation = 'write'
msecs : count distribution
0 -> 1 : 613 |****************************************|
This shows a mixed read/write workload, where the slower read mode was around
10 ms.
USAGE message:
# ./xfsdist -h
usage: xfsdist [-h] [-T] [-m] [-p PID] [interval] [count]
Summarize XFS operation latency
positional arguments:
interval output interval, in seconds
count number of outputs
optional arguments:
-h, --help show this help message and exit
-T, --notimestamp don't include timestamp on interval output
-m, --milliseconds output in milliseconds
-p PID, --pid PID trace this PID only
examples:
./xfsdist # show operation latency as a histogram
./xfsdist -p 181 # trace PID 181 only
./xfsdist 1 10 # print 1 second summaries, 10 times
./xfsdist -m 5 # 5s summaries, milliseconds