Using Intel GPU device with Kata Containers

Using Intel GPU device with Kata Containers

An Intel Graphics device can be passed to a Kata Containers container using GPU passthrough (Intel GVT-d) as well as GPU mediated passthrough (Intel GVT-g).

Intel GVT-d (one VM to one physical GPU) also named as Intel-Graphics-Device passthrough feature is one flavor of graphics virtualization approach. This flavor allows direct assignment of an entire GPU to a single user, passing the native driver capabilities through the hypervisor without any limitations.

Intel GVT-g (multiple VMs to one physical GPU) is a full GPU virtualization solution with mediated pass-through.
A virtual GPU instance is maintained for each VM, with part of performance critical resources, directly assigned. The ability to run a native graphics driver inside a VM without hypervisor intervention in performance critical paths, achieves a good balance among performance, feature, and sharing capability.

Technology	Description	Behaviour	Detail
Intel GVT-d	GPU passthrough	Physical GPU assigned to a single VM	Direct GPU assignment to VM without limitation
Intel GVT-g	GPU sharing	Physical GPU shared by multiple VMs	Mediated passthrough

Hardware Requirements

For client platforms, 5th generation Intel® Core Processor Graphics or higher are required.
For server platforms, E3_v4 or higher Xeon Processor Graphics are required.

The following steps outline the workflow for using an Intel Graphics device with Kata.

Host Kernel Requirements

The following configurations need to be enabled on your host kernel:

CONFIG_VFIO_IOMMU_TYPE1=m
CONFIG_VFIO=m
CONFIG_VFIO_PCI=m
CONFIG_VFIO_MDEV=m
CONFIG_VFIO_MDEV_DEVICE=m
CONFIG_DRM_I915_GVT=m
CONFIG_DRM_I915_GVT_KVMGT=m

Your host kernel needs to be booted with intel_iommu=on on the kernel command line.

Install and configure Kata Containers

To use this feature, you need Kata version 1.3.0 or above. Follow the Kata Containers setup instructions to install the latest version of Kata.

In order to pass a GPU to a Kata Container, you need to enable the hotplug_vfio_on_root_bus configuration in the Kata configuration.toml file as shown below.

$ sudo sed -i -e 's/^# *\(hotplug_vfio_on_root_bus\).*=.*$/\1 = true/g' /usr/share/defaults/kata-containers/configuration.toml

Make sure you are using the pc machine type by verifying machine_type = "pc" is set in the configuration.toml.

Build Kata Containers kernel with GPU support

The default guest kernel installed with Kata Containers does not provide GPU support. To use an Intel GPU with Kata Containers, you need to build a kernel with the necessary GPU support.

The following i915 kernel config options need to be enabled:

CONFIG_DRM=y
CONFIG_DRM_I915=y
CONFIG_DRM_I915_USERPTR=y

Build the Kata Containers kernel with the previous config options, using the instructions described in Building Kata Containers kernel. For further details on building and installing guest kernels, see the developer guide.

There is an easy way to build a guest kernel that supports Intel GPU:

## Build guest kernel with https://github.com/kata-containers/packaging/tree/master/kernel

# Prepare (download guest kernel source, generate .config)
$ ./build-kernel.sh -g intel -f setup

# Build guest kernel
$ ./build-kernel.sh -g intel build

# Install guest kernel
$ sudo -E ./build-kernel.sh -g intel install
/usr/share/kata-containers/vmlinux-intel-gpu.container -> vmlinux-5.4.15-70-intel-gpu
/usr/share/kata-containers/vmlinuz-intel-gpu.container -> vmlinuz-5.4.15-70-intel-gpu

Before using the new guest kernel, please update the kernel parameters in configuration.toml.

kernel = "/usr/share/kata-containers/vmlinuz-intel-gpu.container"

GVT-d with Kata Containers

Use the following steps to pass an Intel Graphics device in GVT-d mode with Kata:

Find the Bus-Device-Function (BDF) for GPU device:
```
$ sudo lspci -nn -D | grep Graphics
  0000:00:02.0 VGA compatible controller [0300]: Intel Corporation Broadwell-U Integrated Graphics [8086:1616] (rev 09)
```
Run the previous command to determine the BDF for the GPU device on host.
From the previous output, PCI address 0000:00:02.0 is assigned to the hardware GPU device.
This BDF is used later to unbind the GPU device from the host.
"8086 1616" is the device ID of the hardware GPU device. It is used later to rebind the GPU device to vfio-pci driver.
Find the IOMMU group for the GPU device:
```
$ BDF="0000:00:02.0"
$ readlink -e /sys/bus/pci/devices/$BDF/iommu_group
/sys/kernel/iommu_groups/1
```
The previous output shows that the GPU belongs to IOMMU group 1.

Unbind the GPU:

$ echo $BDF | sudo tee /sys/bus/pci/devices/$BDF/driver/unbind

Bind the GPU to the vfio-pci device driver:

$ sudo modprobe vfio-pci
$ echo 8086 1616 | sudo tee /sys/bus/pci/drivers/vfio-pci/new_id
$ echo $BDF | sudo tee --append /sys/bus/pci/drivers/vfio-pci/bind

After you run the previous commands, the GPU is bound to vfio-pci driver.
A new directory with the IOMMU group number is created under /dev/vfio:

$ ls -l /dev/vfio
  total 0
  crw------- 1   root root  241,   0 May 18 15:38 1
  crw-rw-rw- 1 root root  10, 196 May 18 15:37 vfio

Start a Kata container with GPU device:

$ sudo docker run -it --runtime=kata-runtime --rm --device /dev/vfio/1 -v /dev:/dev debian /bin/bash

Run lspci within the container to verify the GPU device is seen in the list of the PCI devices. Note the vendor-device id of the GPU ("8086:1616") in the lspci output.

$ lspci -nn -D
  0000:00:00.0 Class [0600]: Device [8086:1237] (rev 02)
  0000:00:01.0 Class [0601]: Device [8086:7000]
  0000:00:01.1 Class [0101]: Device [8086:7010]
  0000:00:01.3 Class [0680]: Device [8086:7113] (rev 03)
  0000:00:02.0 Class [0604]: Device [1b36:0001]
  0000:00:03.0 Class [0780]: Device [1af4:1003]
  0000:00:04.0 Class [0100]: Device [1af4:1004]
  0000:00:05.0 Class [0002]: Device [1af4:1009]
  0000:00:06.0 Class [0200]: Device [1af4:1000]
  0000:00:0f.0 Class [0300]: Device [8086:1616] (rev 09)

Additionally, you can access the device node for the graphics device:

$ ls /dev/dri
  card0  renderD128

GVT-g with Kata Containers

For GVT-g, you append i915.enable_gvt=1 in addition to intel_iommu=on on your host kernel command line and then reboot your host.

Use the following steps to pass an Intel Graphics device in GVT-g mode to a Kata Container:

Find the BDF for GPU device:
```
$ sudo lspci -nn -D | grep Graphics
  0000:00:02.0 VGA compatible controller [0300]: Intel Corporation Broadwell-U Integrated Graphics [8086:1616] (rev 09)
```
Run the previous command to find out the BDF for the GPU device on host. The previous output shows PCI address "0000:00:02.0" is assigned to the GPU device.
Choose the MDEV (Mediated Device) type for VGPU (Virtual GPU):

For background on mdev types, please follow this kernel documentation.
- List out the mdev types for the VGPU:
```
$ BDF="0000:00:02.0"

$ ls /sys/devices/pci0000:00/$BDF/mdev_supported_types
  i915-GVTg_V4_1  i915-GVTg_V4_2  i915-GVTg_V4_4  i915-GVTg_V4_8
```
- Inspect the mdev types and choose one that fits your requirement:
```
$ cd /sys/devices/pci0000:00/0000:00:02.0/mdev_supported_types/i915-GVTg_V4_8 && ls
  available_instances  create  description  device_api  devices

$ cat description
  low_gm_size: 64MB
  high_gm_size: 384MB
  fence: 4
  resolution: 1024x768
  weight: 2

$ cat available_instances
  7
```
  The output of file description represents the GPU resources that are assigned to the VGPU with specified MDEV type.The output of file available_instances represents the remaining amount of VGPUs you can create with specified MDEV type.

Create a VGPU:

Generate a UUID:
```
$ gpu_uuid=$(uuid)
```

Write the UUID to the create file under the chosen mdev type:

$ echo $(gpu_uuid) | sudo tee /sys/devices/pci0000:00/0000:00:02.0/mdev_supported_types/i915-GVTg_V4_8/create

Find the IOMMU group for the VGPU:

$ ls -la /sys/devices/pci0000:00/0000:00:02.0/mdev_supported_types/i915-GVTg_V4_8/devices/${gpu_uuid}/iommu_group
  lrwxrwxrwx 1 root root 0 May 18 14:35 devices/bbc4aafe-5807-11e8-a43e-03533cceae7d/iommu_group -> ../../../../kernel/iommu_groups/0

$ ls -l /dev/vfio
  total 0
  crw-------   1 root root  241,   0 May 18 11:30 0
  crw-rw-rw- 1 root root  10, 196 May 18 11:29 vfio

The IOMMU group "0" is created from the previous output.
Now you can use the device node /dev/vfio/0 in docker command line to pass the VGPU to a Kata Container.

Start Kata container with GPU device enabled:

$ sudo docker run -it --runtime=kata-runtime --rm --device /dev/vfio/0 -v /dev:/dev debian /bin/bash
$ lspci -nn -D
  0000:00:00.0 Class [0600]: Device [8086:1237] (rev 02)
  0000:00:01.0 Class [0601]: Device [8086:7000]
  0000:00:01.1 Class [0101]: Device [8086:7010]
  0000:00:01.3 Class [0680]: Device [8086:7113] (rev 03)
  0000:00:02.0 Class [0604]: Device [1b36:0001]
  0000:00:03.0 Class [0780]: Device [1af4:1003]
  0000:00:04.0 Class [0100]: Device [1af4:1004]
  0000:00:05.0 Class [0002]: Device [1af4:1009]
  0000:00:06.0 Class [0200]: Device [1af4:1000]
  0000:00:0f.0 Class [0300]: Device [8086:1616] (rev 09)

BDF "0000:00:0f.0" is assigned to the VGPU device.

Additionally, you can access the device node for the graphics device:

$ ls /dev/dri
  card0  renderD128

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Intel-GPU-passthrough-and-Kata.md

Intel-GPU-passthrough-and-Kata.md

Using Intel GPU device with Kata Containers

Hardware Requirements

Host Kernel Requirements

Install and configure Kata Containers

Build Kata Containers kernel with GPU support

GVT-d with Kata Containers

GVT-g with Kata Containers

Files

Intel-GPU-passthrough-and-Kata.md

Latest commit

History

Intel-GPU-passthrough-and-Kata.md

File metadata and controls

Using Intel GPU device with Kata Containers

Hardware Requirements

Host Kernel Requirements

Install and configure Kata Containers

Build Kata Containers kernel with GPU support

GVT-d with Kata Containers

GVT-g with Kata Containers