-
Notifications
You must be signed in to change notification settings - Fork 6
/
printer.cfg
71 lines (59 loc) · 2.26 KB
/
printer.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
# This is a Klipper configuration for TronXY X5SA with BigTreeTech Octopus V1.1
# motherboard.
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
### HARDWARE ###
[include hardware/printer.cfg]
[include hardware/axis/XY.cfg]
[include hardware/axis/Z.cfg]
# [include hardware/input_shaper.cfg]
[include hardware/extruder.cfg]
[include hardware/firmware_retraction.cfg]
[include hardware/heated_bed.cfg]
[include hardware/probe.cfg]
[include hardware/fans.cfg]
[include hardware/lights.cfg]
[include hardware/display.cfg]
### MACROS ###
# [include macros/print_base/park.cfg]
[include macros/print_base/pause_resume.cfg]
[include macros/print_base/print_cancel.cfg]
[include macros/print_base/print_end.cfg]
[include macros/print_base/print_start.cfg]
[include macros/probing/adjust_z_offset.cfg]
[include macros/probing/bed_mesh.cfg]
[include macros/probing/crunch_level.cfg]
[include macros/probing/homing.cfg]
# [include macros/probing/klicky_probe.cfg]
[include macros/helpers/filament_swap.cfg]
# [include macros/helpers/heatsoak.cfg]
# [include macros/helpers/lights.cfg]
# [include macros/helpers/nozzle_cleaning.cfg]
[include macros/helpers/temp_check.cfg]
# [include macros/calibration/pa_calibrate.cfg]
# [include macros/miscs/debugging.cfg]
# [include macros/miscs/marlin_compat.cfg]
# [include kiauh_macros.cfg]
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# -0.005000, 0.015000, 0.020000, 0.002500, -0.015000
#*# -0.060000, -0.035000, -0.027500, -0.032500, -0.060000
#*# -0.060000, -0.017500, -0.005000, -0.012500, -0.035000
#*# -0.082500, -0.032500, -0.017500, -0.015000, -0.045000
#*# -0.000000, 0.035000, 0.037500, 0.027500, -0.007500
#*# tension = 0.2
#*# min_x = 20.0
#*# algo = lagrange
#*# y_count = 5
#*# mesh_y_pps = 2
#*# min_y = 20.0
#*# x_count = 5
#*# max_y = 300.0
#*# mesh_x_pps = 2
#*# max_x = 300.0