-
Notifications
You must be signed in to change notification settings - Fork 0
/
printer-20221226_214739.cfg
189 lines (154 loc) · 5.92 KB
/
printer-20221226_214739.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
# This file contains common pin mappings for the BigTreeTech Octopus V1.
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
# after running "make", copy the generated "klipper/out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
# See docs/Config_Reference.md for a description of parameters.
## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
## *** THINGS TO CHANGE/CHECK: ***
## MCU paths [mcu] section
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
## Z Endstop Switch location [safe_z_home] section
## Homing end position [gcode_macro G32] section
## Z Endstop Switch offset for Z0 [stepper_z] section
## Probe points [quad_gantry_level] section
## Min & Max gantry corner postions [quad_gantry_level] section
## PID tune [extruder] and [heater_bed] sections
## Thermistor types [extruder] and [heater_bed] sections
## Probe pin [probe] section
## Fine tune E steps [extruder] section
# This file contains common pin mappings for the BigTreeTech SKR 2 & Ender 6.
# To use this config, the firmware should be compiled for the
# STM32F407 with a "32KiB bootloader".
# The "make flash" command does not work on the SKR 2. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the SKR 2
# with that SD card.
### HARDWARE ###
[include hardware/printer.cfg]
[include hardware/axis/XY.cfg]
[include hardware/axis/Z.cfg]
[include hardware/input_shaper.cfg]
[include hardware/extruder.cfg]
# [include hardware/firmware_retraction.cfg]
[include hardware/heated_bed.cfg]
[include hardware/probe.cfg]
[include hardware/fans.cfg]
[include hardware/temperature_sensors.cfg]
[include hardware/lights.cfg]
# [include hardware/display.cfg]
### MACROS ###
[include macros/print_base/park.cfg]
[include macros/print_base/pause_resume.cfg]
[include macros/print_base/print_cancel.cfg]
[include macros/print_base/print_end.cfg]
[include macros/print_base/print_start.cfg]
#[include macros/probing/non-klicky/adjust_z_offset.cfg] # replaced by klicky probe
[include macros/probing/bed_mesh.cfg]
[include macros/probing/homing.cfg]
[include macros/probing/klicky-probe.cfg]
# [include macros/helpers/filament_swap.cfg]
[include macros/helpers/heatsoak.cfg]
# [include macros/helpers/search_vars.cfg]
# [include macros/helpers/lights.cfg]
[include macros/helpers/nozzle_cleaning.cfg]
[include macros/helpers/up_front.cfg]
[include macros/helpers/temp_check.cfg]
[include macros/calibration/pa_calibrate.cfg]
[include macros/misc/power_off.cfg]
# [include macros/misc/debugging.cfg]
# [include macros/misc/marlin_compat.cfg]
#####################################################################
# LED Control
#####################################################################
## Chamber Lighting - HE2 Connector (Optional)
#[output_pin caselight]
#pin: PB10
#pwm:true
#shutdown_value: 0
#value:1
#cycle_time: 0.01
########################################
# EXP1 / EXP2 (display) pins
########################################
[board_pins]
aliases:
# EXP1 header
EXP1_1=PE8, EXP1_2=PE7,
EXP1_3=PE9, EXP1_4=PE10,
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
EXP1_7=PE14, EXP1_8=PE15,
EXP1_9=<GND>, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PA6, EXP2_2=PA5,
EXP2_3=PB1, EXP2_4=PA4,
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
EXP2_7=PC15, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=<5V>
#####################################################################
# Displays
#####################################################################
## Uncomment the display that you have
#--------------------------------------------------------------------
#[display]
## RepRapDiscount 128x64 Full Graphic Smart Controller
#lcd_type: st7920
#cs_pin: EXP1_4
#sclk_pin: EXP1_5
#sid_pin: EXP1_3
#menu_timeout: 40
#encoder_pins: ^EXP2_5, ^EXP2_3
#click_pin: ^!EXP1_2
#[output_pin beeper]
#pin: EXP1_1
#--------------------------------------------------------------------
#[display]
## mini12864 LCD Display
#lcd_type: uc1701
#cs_pin: EXP1_3
#a0_pin: EXP1_4
#rst_pin: EXP1_5
#encoder_pins: ^EXP2_5, ^EXP2_3
#click_pin: ^!EXP1_2
#contrast: 63
#spi_software_miso_pin: EXP2_1
#spi_software_mosi_pin: EXP2_6
#spi_software_sclk_pin: EXP2_2
#[neopixel btt_mini12864]
## To control Neopixel RGB in mini12864 display
#pin: EXP1_6
#chain_count: 3
#initial_RED: 0.1
#initial_GREEN: 0.5
#initial_BLUE: 0.0
#color_order: RGB
## Set RGB values on boot up for each Neopixel.
## Index 1 = display, Index 2 and 3 = Knob
#[delayed_gcode setdisplayneopixel]
#initial_duration: 1
#gcode:
# SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
#--------------------------------------------------------------------
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.118750, 0.058750, 0.008750, 0.026250, 0.116250
#*# 0.102500, 0.051250, -0.015000, 0.015000, 0.110000
#*# 0.100000, 0.050000, 0.000000, 0.033750, 0.140000
#*# 0.112500, 0.056250, 0.011250, 0.045000, 0.142500
#*# 0.123750, 0.055000, 0.008750, 0.031250, 0.126250
#*# tension = 0.2
#*# min_x = 10.0
#*# algo = bicubic
#*# y_count = 5
#*# mesh_y_pps = 2
#*# min_y = 25.0
#*# x_count = 5
#*# max_y = 270.0
#*# mesh_x_pps = 2
#*# max_x = 280.0