Minor procedure updates

Author: bergie

docs/checklists/01_before_sailing.md

@@ -4,7 +4,7 @@
 
 - [ ] Check [[weather|weather forecast]]
 - [ ] [[navigation#Planning a coastal/inland route|Plan route]] and set up in plotter
-- [ ] [[electrics#^115922|Charge battery to 100%]] if needed
+- [ ] [[electrics#Charging batteries to full|Charge battery to 100%]] if needed
 - [ ] Do [[#When going offshore|offshore preparations]] as needed
 - [ ] Decide [[sails#Sail plan|sail plan]]
 - [ ] Update sail plan and crew list in [logbook](http://192.168.2.105/admin/#/e/_meri_imperiumi_signalk_logbook)
@@ -27,7 +27,6 @@
 - [ ] Stow bow anchor in anchor locker
 - [ ] Install bowsprit
 - [ ] Put cork on heater exhaust and turn off heater circuit
-- [ ] Ensure banana-boot is tied securely
 - [ ] Hank on and secure staysail
 - [ ] Install jacklines
 - [ ] Ensure emergency contacts know the plan
@@ -80,7 +79,6 @@
 - [ ] [[engine#Starting the engine|Start engine]]
 - [ ] Check that water is coming out of exhaust 
 - [ ] Ensure all of the crew is on board
-- [ ] Prepare intercom headsets
 - [ ] Life vests on
 - [ ] Apply sunscreen
 - [ ] Harbour departure briefing

docs/checklists/03_anchoring.md

@@ -17,10 +17,9 @@ Bow anchoring is used in most anchorages outside of Scandinavia.
 - [ ] Check other vessels for appropriate swinging room
 - [ ] Double-check chart data with depth sounder
 - [ ] Remove the safety shackle from anchor
-- [ ] Uncoil and prepare the anchor buoy line
+- [ ] Uncoil and prepare the anchor trip line
 - [ ] Prepare appropriate anchor chain on deck (about 4✕ depth)
 - [ ] Prepare for setting up anchor alarm (log [into Signal K](http://192.168.2.105/@signalk/freeboard-sk/) etc)
-- [ ] Prepare intercom headsets
 
 ### Setting the anchor
 
@@ -35,7 +34,7 @@ Bow anchoring is used in most anchorages outside of Scandinavia.
 - [ ] Then start backing again, slowly increasing power
 - [ ] Check that the anchor holds (transits to landmarks, speed 0kt when chain tight)
 - [ ] When setting anchor with engine, about 1500 RPM is a good number to reach
-- [ ] Pull up and reanchor if the anchor doesn't hold
+- [ ] Pull up and re-anchor if the anchor doesn't hold
 
 ### After anchor is set
 

docs/checklists/04_after_sailing.md

@@ -20,7 +20,7 @@
 - [ ] Coil and stow all lines
 - [ ] Plug in shore power if using
 - [ ] Deploy [[electrics#FLINsail|FLINsail]] unless on shore power or the winds are too strong
-- [ ] Move main halyard to the end of the boom unless used for FLINsail
+- [ ] Tie main halyard to lazyjacks unless used for FLINsail
 - [ ] Deploy bathing ladder
 - [ ] If cold or rainy weather is expected, set up the cockpit enclosure
 - [ ] Deploy winch covers

docs/checklists/05_leaving_the_vessel.md

@@ -2,7 +2,7 @@
 
 ## Inside the vessel
 
-- [ ] Pickle the watermaker and remove filter if leaving the boat for longer than a week
+- [ ] Pickle the [[plumbing#Watermaker|watermaker]] and remove filter if leaving the boat for longer than a week
 - [ ] Open saloon bunks for ventilation
 - [ ] Open v-berth bunks for ventilation
 - [ ] Close and lock front hatch

docs/systems/electrics.md

@@ -92,8 +92,6 @@ The shore power charger is set to [solar priority mode](https://www.victronenerg
 
 #### Charging batteries to full
 
-^115922
-
 - [ ] Ensure shore power is plugged in
 - [ ] Open a browser to the [Cerbo GX screen](http://venus.local)
 - [ ] Open MultiPlus settings