If you have a Raspberry Pi and the official 7" touchscreen and you're trying to play ScummVM games you may be disappointed to find it doesn't work. That is, while you can move the mouse pointer using the touchscreen you cannot 'click' on buttons by touching the touchscreen alone. This is because the default Raspbian driver presents itself as a touchscreen device and touchscreen events are not picked up by ScummVM for some reason.
This repository presents a workaround in the form of a Raspberry Pi's touchscreen driver that presents itself as a mouse instead of a touchscreen, making it 'ScummVM-compatible'. As a bonus, the driver also emits a 'F5' key press when you press the screen with two fingers, making it easier to save and load games without plugging in a keyboard.
To use this driver, follow either the quickstart or slowstart below.
- Quickstart: If you're lucky these instructions may be all you need!
- Slowstart: A method that should work for everyone but is unfortunately quite time consuming.
The quickstart with only work for you if you are lucky enough to be running the correct version of the Raspberry Pi's kernel. If you are not so lucky follow the slowstart instructions instead!
- This driver is compatible with Rasberry Pi kernel version
4.14.76-v7+(tagrpi-4.14.y) and has been tested with Raspbian GNU/Linux 9 (stretch). I was not able to get this implementation to work with some other kernel versions but your mileage may vary. See what kernel you are running by callinguname -r. If it is4.14.76-v7+you can continue with this quickstart and install the associated kernel headers withsudo apt-get install raspberrypi-kernel-headers. - Compile the driver out-of-tree by calling
make. If this fails you are probably not running with a4.14.76-v7+kernel or you don't have the appropriate kernel headers installed and the quickstart won't work for you. Note that if you are running a different kernel the driver may still compile but the resulting kernel module may not work. - Following compilation, test whether or not you can load the driver successfully by using
sudo insmod mxklabs-rpi-ft5406-scummvm.koand check for errors in thedmesglog. If you see any error traces related to the driver you're probably not running4.14.76-v7+or your kernel was compiled with a different compiler and this quickstart won't work for you. Note that a message to say your kernel is tainted is normal with this quickstart method. Also, if all is well don't worry if the touch screen does not work at this point. - Loading the driver with
insmodis a good way of testing whether the driver was compiled correctly but doesn't result in a functioning touchscreen. The next step is to load the driver on start-up by replacing the default touchscreen driver file/lib/modules/4.14.76-v7+/kernel/drivers/input/touchscreen/rpi-ft5406.kowith themxklabs-rpi-ft5406-scummvm.kodriver you compiled. Make sure the permissions and ownerships as per the originalrpi-ft5406.ko! It is probably a good idea to make a backup of the originalrpi-ft5406.koso that you can switch back later if you want to. You're done!
The slowstart instructions involve compiling and installing a new kernel on your Raspberry Pi. For instructions on how to do this I'll mostly refer you to the instructions in this official guide. However, there are a few additional instructions you need to follow to ensure you are including this repository's touchscreen driver in your kernel instead of the default one. Note that compiling the kernel on the Raspberry Pi itself will take many hours.
-
Before you start you need to clone this repository somewhere using
git clone https://github.com/mxklabs/mxklabs-rpi-ft5406-scummvm.git. When you get to official guide's instruction to clone the Raspberry Pi's linux repository it makes sense to do so in the same parent directory. -
When you get to official guide's instruction to clone the Raspberry Pi's linux repository it tells you to checkout only one tag. If you do this make sure you check out tag
rpi-4.14.y. Alternatively, clone the entire repository and then checkout therpi-4.14.ytag usinggit checkout rpi-4.14.y. -
Before you get to the instruction to run
make -j4 zImage modules dtbsyou need to replace the source code indrivers/input/touchscreen/rpi-ft5406.cwith the contents of this repository'smxklabs-rpi-ft5406-scummvm.c. One way of doing this is by removing the original file and creating a symbolic link. If you checked out both this repository and the Raspberry Pi's linux repository in the same directory you can do this with the following command:rm ./linux/drivers/input/touchscreen/rpi-ft5406.c ln -s ./mxklabs-rpi-ft5406-scummvm/mxklabs-rpi-ft5406-scummvm.c ./linux/drivers/input/touchscreen/rpi-ft5406.c
- Note that by using this driver you will lose multi-touch capabilities. You will have to revert back to the original
rpi-ft5406.kodriver to get get this functionality back. This is probably something that could be fixed in a future version. - Note that changing the driver is a bit of a roundabout way of fixing the problem. A proper fix would entail changing ScummVM source code itself to ensure that ScummVM acts on touchscreen events. Also, in my opinion, this driver is not really production-ready. It's a hack, don't use it to judge my coding skills! I made the code publicly available only to help people looking to solve the same problem.
- You may find it quite useful to remotely control your Raspberry Pi from your phone or tablet using a RealVNC client app. You can use this method to perform any kind of small mouse or keyboard-based input task (such as typing names of save games). This avoids the need to physically plug in a mouse or keyboard and allows you to control the Pi from a distance. Read these instructions if you are interested.
- The driver in this repository is mostly copied from the original
rpi-ft5406.cfile in the official Raspberry Pi linux repository which is credited to Gordon Hollingworth. Changes to make this driver ScummVM compatible were made by Mark Kattenbelt.