O大，求助。外货M16盒子或烨晨YC01盒子，CPU:S905X;2+16gb,刷armbian系统，2GB运存只能识别到1GB运存内存，问题。

[lzw20201111]

配置：
设备型号：烨晨YC01盒子，或M16 TV BOX盒子
CPU:S905X
运存：2GB
内存：16GB
刷armbian固件：Armbian_24.8.0_amlogic_s905x-t95_bullseye_6.6.39_server_2024.07.15.img.gz
已按以下贴教程方法处理过，依然识别不了2GB运存，只能识别到1GB运存。
参考贴教程1：O大，求助，我用的三陶教育s30盒子刷armbian mcu是s905d2，刷s905X固件，内存识别788M，不准确。 #2363
#2363
参考贴教程2：s905lb的版本内存都只能识别到788M。 #2355
#2355
参考贴教程3：reduced RAM in X96 Max+ A100 -- dtb mistake #602
ophub/amlogic-s9xxx-openwrt#602
自行已修改过DTB文件了。
请问有那位大佬，能解决一下吗？谢谢！！

开机信息：
root@armbian:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.10.221-ophub (root@fv-az1247-290) (aarch64-none-linux-gnu-gcc (Arm GNU Toolchain 13.3.Rel1 (Build arm-13.24)) 13.3.1 20240614, GNU ld (Arm GNU Toolchain 13.3.Rel1 (Build arm-13.24)) 2.42.0.20240614) #1 SMP PREEMPT Sun Jul 14 06:45:24 EDT 2024
[ 0.000000] Machine model: Amlogic Meson GXL (S905X) P212 Development Board
[ 0.000000] efi: UEFI not found.
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'hwrom@0': base 0x0000000000000000, size 16 MiB
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000002b000000, size 256 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000003f806fff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x00000000052fffff]
[ 0.000000] node 0: [mem 0x0000000005300000-0x00000000072fffff]
[ 0.000000] node 0: [mem 0x0000000007300000-0x000000000fffffff]
[ 0.000000] node 0: [mem 0x0000000010000000-0x00000000101fffff]
[ 0.000000] node 0: [mem 0x0000000010200000-0x000000003f806fff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003f806fff]
[ 0.000000] On node 0 totalpages: 260103
[ 0.000000] DMA zone: 4065 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 260103 pages, LIFO batch:63
[ 0.000000] On node 0, zone DMA: 505 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] percpu: Embedded 22 pages/cpu s51352 r8192 d30568 u90112
[ 0.000000] pcpu-alloc: s51352 r8192 d30568 u90112 alloc=22*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 256038
[ 0.000000] Kernel command line: root=UUID=87f9314c-1e35-4973-8049-0e9f20ca4f77 rootflags=data=writeback rw rootfstype=ext4 c onsole=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 max_loop=128 l oglevel=1 voutmode=hdmi disablehpd=false overscan=100 sdrmode=auto
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 665592K/1040412K available (14720K kernel code, 2658K rwdata, 5828K rodata, 3840K init, 881K bss, 112676K reserved, 262144K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000429] Console: colour dummy device 80x25
[ 0.000460] printk: console [tty0] enabled
[ 0.000500] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.000511] pid_max: default: 32768 minimum: 301
[ 0.000773] LSM: Security Framework initializing
[ 0.000856] SELinux: Initializing.
[ 0.001067] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001080] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.003191] rcu: Hierarchical SRCU implementation.
[ 0.004644] EFI services will not be available.
[ 0.005099] smp: Bringing up secondary CPUs ...
[ 0.005731] Detected VIPT I-cache on CPU1
[ 0.005800] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.006518] Detected VIPT I-cache on CPU2
[ 0.006572] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.007339] Detected VIPT I-cache on CPU3
[ 0.007390] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.007490] smp: Brought up 1 node, 4 CPUs
[ 0.007500] SMP: Total of 4 processors activated.
[ 0.007506] CPU features: detected: 32-bit EL0 Support
[ 0.007512] CPU features: detected: CRC32 instructions
[ 0.007517] CPU features: detected: 32-bit EL1 Support
[ 0.008178] CPU: All CPU(s) started at EL2
[ 0.008198] alternatives: patching kernel code
[ 0.009288] devtmpfs: initialized
[ 0.017538] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.017563] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.025123] prandom: seed boundary self test passed
[ 0.026616] prandom: 100 self tests passed
[ 0.048695] prandom32: self test passed (less than 6 bits correlated)
[ 0.048747] pinctrl core: initialized pinctrl subsystem
[ 0.049381] DMI not present or invalid.
[ 0.049890] NET: Registered protocol family 16
[ 0.052154] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.052263] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.052383] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.052472] audit: initializing netlink subsys (disabled)
[ 0.052743] audit: type=2000 audit(0.049:1): state=initialized audit_enabled=0 res=1
[ 0.053930] thermal_sys: Registered thermal governor 'step_wise'
[ 0.054235] cpuidle: using governor ladder
[ 0.054444] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.054545] ASID allocator initialised with 65536 entries
[ 0.054676] Serial: AMBA PL011 UART driver
[ 0.086590] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.086603] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.086608] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.086613] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 1.587926] cryptd: max_cpu_qlen set to 1000
[ 1.591812] "cryptomgr_test" (93) uses obsolete ecb(arc4) skcipher
[ 1.605944] alg: No test for 842 (842-generic)
[ 1.606064] alg: No test for 842 (842-scomp)
[ 1.705087] DRBG: Continuing without Jitter RNG
[ 1.772728] raid6: neonx8 gen() 2224 MB/s
[ 1.829454] raid6: neonx8 xor() 1613 MB/s
[ 1.886182] raid6: neonx4 gen() 2190 MB/s
[ 1.942916] raid6: neonx4 xor() 1535 MB/s
[ 1.999653] raid6: neonx2 gen() 2083 MB/s
[ 2.056382] raid6: neonx2 xor() 1423 MB/s
[ 2.113123] raid6: neonx1 gen() 1795 MB/s
[ 2.169844] raid6: neonx1 xor() 1217 MB/s
[ 2.226579] raid6: int64x8 gen() 1415 MB/s
[ 2.283296] raid6: int64x8 xor() 740 MB/s
[ 2.340022] raid6: int64x4 gen() 1570 MB/s
[ 2.396786] raid6: int64x4 xor() 810 MB/s
[ 2.453484] raid6: int64x2 gen() 1402 MB/s
[ 2.510210] raid6: int64x2 xor() 750 MB/s
[ 2.566948] raid6: int64x1 gen() 1036 MB/s
[ 2.623661] raid6: int64x1 xor() 517 MB/s
[ 2.623666] raid6: using algorithm neonx8 gen() 2224 MB/s
[ 2.623670] raid6: .... xor() 1613 MB/s, rmw enabled
[ 2.623675] raid6: using neon recovery algorithm
[ 2.623967] ACPI: Interpreter disabled.
[ 2.626241] iommu: Default domain type: Translated
[ 2.626649] vgaarb: loaded
[ 2.627273] SCSI subsystem initialized
[ 2.627508] usbcore: registered new interface driver usbfs
[ 2.627545] usbcore: registered new interface driver hub
[ 2.627584] usbcore: registered new device driver usb
[ 2.628105] mc: Linux media interface: v0.10
[ 2.628146] videodev: Linux video capture interface: v2.00
[ 2.628420] EDAC MC: Ver: 3.0.0
[ 2.629686] Advanced Linux Sound Architecture Driver Initialized.
[ 2.630864] clocksource: Switched to clocksource arch_sys_counter
[ 2.631259] VFS: Disk quotas dquot_6.6.0
[ 2.631332] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.631488] FS-Cache: Loaded
[ 2.632593] pnp: PnP ACPI: disabled
[ 2.639438] NET: Registered protocol family 2
[ 2.639627] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.640490] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 2.640522] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 2.640629] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 2.640742] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.641081] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[ 2.641165] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 2.641193] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 2.641355] NET: Registered protocol family 1
[ 2.641383] NET: Registered protocol family 44
[ 2.641400] PCI: CLS 0 bytes, default 64
[ 2.641625] Trying to unpack rootfs image as initramfs...
[ 6.332363] Freeing initrd memory: 11744K
[ 6.333362] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 6.333890] kvm [1]: IPA Size Limit: 40 bits
[ 6.334834] kvm [1]: vgic interrupt IRQ9
[ 6.334958] kvm [1]: Hyp mode initialized successfully
[ 6.624885] Initialise system trusted keyrings
[ 6.625167] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 6.631757] zbud: loaded
[ 6.633547] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 6.634141] fuse: init (API version 7.32)
[ 6.634713] SGI XFS with ACLs, security attributes, quota, no debug enabled
[ 6.676194] NET: Registered protocol family 38
[ 6.732018] xor: measuring software checksum speed
[ 6.736198] 8regs : 2366 MB/sec
[ 6.739721] 32regs : 2802 MB/sec
[ 6.744355] arm64_neon : 2130 MB/sec
[ 6.744360] xor: using function: 32regs (2802 MB/sec)
[ 6.744375] Key type asymmetric registered
[ 6.744381] Asymmetric key parser 'x509' registered
[ 6.744446] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 6.744653] io scheduler mq-deadline registered
[ 6.744659] io scheduler kyber registered
[ 6.744855] io scheduler bfq registered
[ 6.806503] soc soc0: Amlogic Meson GXL (S905M2) Revision 21:d (e4:2) Detected
[ 6.809219] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[ 6.811434] Serial: AMBA driver
[ 6.811950] c11084c0.serial: ttyAML6 at MMIO 0xc11084c0 (irq = 20, base_baud = 1500000) is a meson_uart
[ 6.812157] serial serial0: tty port ttyAML6 registered
[ 6.812808] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 23, base_baud = 1500000) is a meson_uart
[ 6.812930] printk: console [ttyAML0] enabled
[ 6.823467] brd: module loaded
[ 9.074251] loop: module loaded
[ 9.081792] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.081817] ehci-pci: EHCI PCI platform driver
[ 9.081888] ehci-platform: EHCI generic platform driver
[ 9.082555] usbcore: registered new interface driver cdc_wdm
[ 9.082623] usbcore: registered new interface driver usb-storage
[ 9.083159] mousedev: PS/2 mouse device common for all mice
[ 9.085214] meson-vrtc c81000a8.rtc: registered as rtc0
[ 9.085259] meson-vrtc c81000a8.rtc: setting system clock to 1970-01-01T00:00:09 UTC (9)
[ 9.085814] i2c /dev entries driver
[ 9.088266] Registered IR keymap rc-cec
[ 9.088432] rc rc0: meson_ao_cec as /devices/platform/soc/c8100000.bus/c8100100.cec/rc/rc0
[ 9.088617] input: meson_ao_cec as /devices/platform/soc/c8100000.bus/c8100100.cec/rc/rc0/input0
[ 9.092757] Synopsys Designware Multimedia Card Interface Driver
[ 9.094437] meson-gx-mmc d0072000.mmc: Got CD GPIO
[ 9.096068] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
[ 9.096094] meson-sm: secure-monitor enabled
[ 9.098434] gxl-crypto c883e000.crypto: will run requests pump with realtime priority
[ 9.098583] gxl-crypto c883e000.crypto: will run requests pump with realtime priority
[ 9.102338] hid: raw HID events driver (C) Jiri Kosina
[ 9.102517] usbcore: registered new interface driver usbhid
[ 9.102521] usbhid: USB HID core driver
[ 9.102948] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered
[ 9.110672] Initializing XFRM netlink socket
[ 9.111370] NET: Registered protocol family 10
[ 9.158818] Segment Routing with IPv6
[ 9.158829] RPL Segment Routing with IPv6
[ 9.159017] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 9.160322] NET: Registered protocol family 17
[ 9.160360] NET: Registered protocol family 15
[ 9.160600] 8021q: 802.1Q VLAN Support v1.8
[ 9.161363] registered taskstats version 1
[ 9.161386] Loading compiled-in X.509 certificates
[ 9.164615] zswap: loaded using pool zstd/zbud
[ 9.165187] Key type .fscrypt registered
[ 9.165195] Key type fscrypt-provisioning registered
[ 9.166667] Btrfs loaded, crc32c=crc32c-generic
[ 9.199730] meson-drm d0100000.vpu: Queued 3 outputs on vpu
[ 9.227616] meson-dw-hdmi c883a000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[ 9.228228] meson-dw-hdmi c883a000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[ 9.229340] meson-drm d0100000.vpu: bound c883a000.hdmi-tx (ops meson_dw_hdmi_ops)
[ 9.230065] [drm] Initialized meson 1.0.0 20161109 for d0100000.vpu on minor 0
[ 9.254176] mmc2: new HS200 MMC card at address 0001
[ 9.255249] mmcblk2: mmc2:0001 AFEABB 14.7 GiB
[ 9.255742] mmcblk2boot0: mmc2:0001 AFEABB partition 1 4.00 MiB
[ 9.256214] mmcblk2boot1: mmc2:0001 AFEABB partition 2 4.00 MiB
[ 9.256426] mmcblk2rpmb: mmc2:0001 AFEABB partition 3 512 KiB, chardev (241:0)
[ 9.343813] [drm] kms: can't enable cloning when we probably wanted to.
[ 9.349397] fbcon: Deferring console take-over
[ 9.349417] meson-drm d0100000.vpu: [drm] fb0: mesondrmfb frame buffer device
[ 9.351491] meson8b-dwmac c9410000.ethernet: IRQ eth_wake_irq not found
[ 9.351503] meson8b-dwmac c9410000.ethernet: IRQ eth_lpi not found
[ 9.351663] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[ 9.352714] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 9.352728] meson8b-dwmac c9410000.ethernet: DWMAC1000
[ 9.352735] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[ 9.352741] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[ 9.352747] meson8b-dwmac c9410000.ethernet: COE Type 2
[ 9.352752] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[ 9.352757] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[ 9.352764] meson8b-dwmac c9410000.ethernet: Normal descriptors
[ 9.352769] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[ 9.352774] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 9.355994] dwc3-meson-g12a d0078080.usb: USB2 ports: 2
[ 9.356007] dwc3-meson-g12a d0078080.usb: USB3 ports: 0
[ 9.868848] dwc2 c9100000.usb: supply vusb_d not found, using dummy regulator
[ 9.869057] dwc2 c9100000.usb: supply vusb_a not found, using dummy regulator
[ 9.869360] dwc2 c9100000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[ 9.871729] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 9.872019] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 1
[ 9.872173] xhci-hcd xhci-hcd.4.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x0000000002010010
[ 9.872255] xhci-hcd xhci-hcd.4.auto: irq 50, io mem 0xc9000000
[ 9.872488] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 9.872682] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2
[ 9.872711] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 9.872887] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 9.872894] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.872900] usb usb1: Product: xHCI Host Controller
[ 9.872905] usb usb1: Manufacturer: Linux 5.10.221-ophub xhci-hcd
[ 9.872910] usb usb1: SerialNumber: xhci-hcd.4.auto
[ 9.873395] hub 1-0:1.0: USB hub found
[ 9.873427] hub 1-0:1.0: 2 ports detected
[ 9.873813] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 9.873931] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 9.873938] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.873944] usb usb2: Product: xHCI Host Controller
[ 9.873949] usb usb2: Manufacturer: Linux 5.10.221-ophub xhci-hcd
[ 9.873954] usb usb2: SerialNumber: xhci-hcd.4.auto
[ 9.874519] hub 2-0:1.0: USB hub found
[ 9.874562] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 9.878690] meson-gx-mmc d0070000.mmc: allocated mmc-pwrseq
[ 9.880627] scpi_protocol scpi: SCP Protocol legacy pre-1.0 firmware
[ 9.890821] simple-framebuffer 3f807000.framebuffer: framebuffer at 0x3f807000, 0x7e9000 bytes, mapped to 0x(ptrval)
[ 9.890913] simple-framebuffer 3f807000.framebuffer: format=x8r8g8b8, mode=1920x1080x32, linelength=7680
[ 9.891306] fbcon: Deferring console take-over
[ 9.891329] simple-framebuffer 3f807000.framebuffer: fb1: simplefb registered!
[ 9.914950] clk: Disabling unused clocks
[ 9.915273] ALSA device list:
[ 9.915281] No soundcards found.
[ 9.918431] Freeing unused kernel memory: 3840K
[ 9.928049] mmc0: new high speed SDIO card at address 0001
[ 9.937596] Run /init as init process
[ 9.937605] with arguments:
[ 9.937610] /init
[ 9.937614] with environment:
[ 9.937618] HOME=/
[ 9.937622] TERM=linux
[ 9.937626] voutmode=hdmi
[ 9.937631] disablehpd=false
[ 9.937634] overscan=100
[ 9.937638] sdrmode=auto
[ 9.972067] fbcon: Taking over console
[ 10.121196] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 10.133401] Console: switching to colour frame buffer device 240x67
[ 10.266126] usb 1-2: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.35
[ 10.266171] usb 1-2: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 10.266199] usb 1-2: Product: USB3.0 Card Reader
[ 10.266223] usb 1-2: Manufacturer: Generic
[ 10.266247] usb 1-2: SerialNumber: 000000001536
[ 10.271865] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 10.273589] scsi host0: usb-storage 1-2:1.0
[ 10.977784] Registered IR keymap rc-cec
[ 10.978001] rc rc1: dw_hdmi as /devices/platform/soc/c883a000.hdmi-tx/rc/rc1
[ 10.978281] input: dw_hdmi as /devices/platform/soc/c883a000.hdmi-tx/rc/rc1/input1
[ 11.014140] lima d00c0000.gpu: gp - mali450 version major 0 minor 0
[ 11.016289] lima d00c0000.gpu: pp0 - mali450 version major 0 minor 0
[ 11.016420] lima d00c0000.gpu: pp1 - mali450 version major 0 minor 0
[ 11.016539] lima d00c0000.gpu: pp2 - mali450 version major 0 minor 0
[ 11.016605] lima d00c0000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus
[ 11.016616] lima d00c0000.gpu: l2 cache 64K, 4-way, 64byte cache line, 128bit external bus
[ 11.019102] lima d00c0000.gpu: bus rate = 166666667
[ 11.019116] lima d00c0000.gpu: mod rate = 24000000
[ 11.019320] lima d00c0000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19
[ 11.022996] [drm] Initialized lima 1.1.0 20191231 for d00c0000.gpu on minor 1
[ 11.282382] scsi 0:0:0:0: Direct-Access Generic MassStorageClass 1536 PQ: 0 ANSI: 6
[ 11.529201] sd 0:0:0:0: [sda] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 11.530047] sd 0:0:0:0: [sda] Write Protect is off
[ 11.530067] sd 0:0:0:0: [sda] Mode Sense: 21 00 00 00
[ 11.530888] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 11.569423] sda: sda1 sda2
[ 11.602700] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 12.396087] EXT4-fs (sda2): mounted filesystem with writeback data mode. Opts: data=writeback
[ 13.229639] systemd[1]: System time before build time, advancing clock.
[ 13.410003] systemd[1]: systemd 247.3-7+deb11u5 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=un ified)
[ 13.416396] systemd[1]: Detected architecture arm64.
[ 13.440268] systemd[1]: Set hostname to .
[ 14.445078] systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed.
[ 14.634743] systemd[1]: Queued start job for default target Graphical Interface.
[ 14.636869] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.655735] systemd[1]: Created slice system-getty.slice.
[ 14.656319] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.658766] systemd[1]: Created slice system-modprobe.slice.
[ 14.659072] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.661819] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 14.664609] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 14.666785] systemd[1]: Created slice User and Session Slice.
[ 14.667507] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 14.668980] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 14.669780] systemd[1]: Reached target Slices.
[ 14.670076] systemd[1]: Reached target Swap.
[ 14.670339] systemd[1]: Reached target System Time Set.
[ 14.694032] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 14.695858] systemd[1]: Listening on Syslog Socket.
[ 14.697450] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 14.698546] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 14.700494] systemd[1]: Listening on Journal Audit Socket.
[ 14.702225] systemd[1]: Listening on Journal Socket (/dev/log).
[ 14.703987] systemd[1]: Listening on Journal Socket.
[ 14.705938] systemd[1]: Listening on udev Control Socket.
[ 14.707075] systemd[1]: Listening on udev Kernel Socket.
[ 14.713599] systemd[1]: Mounting Huge Pages File System...
[ 14.720820] systemd[1]: Mounting POSIX Message Queue File System...
[ 14.728664] systemd[1]: Mounting RPC Pipe File System...
[ 14.736263] systemd[1]: Mounting Kernel Debug File System...
[ 14.737856] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 14.738646] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 14.747081] systemd[1]: Starting Restore / save the current clock...
[ 14.755304] systemd[1]: Starting Set the console keyboard layout...
[ 14.763112] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 14.771922] systemd[1]: Starting Load Kernel Module configfs...
[ 14.777422] RPC: Registered named UNIX socket transport module.
[ 14.777435] RPC: Registered udp transport module.
[ 14.777439] RPC: Registered tcp transport module.
[ 14.777443] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.782588] systemd[1]: Starting Load Kernel Module drm...
[ 14.790001] systemd[1]: Starting Load Kernel Module fuse...
[ 14.797827] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 14.798168] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 14.809859] systemd[1]: Starting Load Kernel Modules...
[ 14.817047] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 14.825489] systemd[1]: Starting Coldplug All udev Devices...
[ 14.839153] systemd[1]: Mounted Huge Pages File System.
[ 14.840821] systemd[1]: Mounted POSIX Message Queue File System.
[ 14.842611] systemd[1]: Mounted RPC Pipe File System.
[ 14.844101] systemd[1]: Mounted Kernel Debug File System.
[ 14.847491] systemd[1]: Finished Restore / save the current clock.
[ 14.851491] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 14.854012] systemd[1]: modprobe@configfs.service: Succeeded.
[ 14.855855] systemd[1]: Finished Load Kernel Module configfs.
[ 14.858238] systemd[1]: modprobe@drm.service: Succeeded.
[ 14.859934] systemd[1]: Finished Load Kernel Module drm.
[ 14.863567] systemd[1]: modprobe@fuse.service: Succeeded.
[ 14.865143] systemd[1]: Finished Load Kernel Module fuse.
[ 14.868509] systemd[1]: Finished Load Kernel Modules.
[ 14.871435] EXT4-fs (sda2): re-mounted. Opts: commit=600,errors=remount-ro
[ 14.877801] systemd[1]: Mounting FUSE Control File System...
[ 14.885744] systemd[1]: Mounting Kernel Configuration File System...
[ 14.893962] systemd[1]: Starting Apply Kernel Variables...
[ 14.909749] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 14.911788] systemd[1]: Mounted FUSE Control File System.
[ 14.913568] systemd[1]: Mounted Kernel Configuration File System.
[ 14.918195] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 14.918545] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 14.924536] systemd[1]: Starting Load/Save Random Seed...
[ 14.932862] systemd[1]: Starting Create System Users...
[ 15.022582] systemd[1]: Finished Apply Kernel Variables.
[ 15.047341] systemd[1]: Finished Create System Users.
[ 15.057782] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 15.134506] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 15.148774] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[ 15.193604] systemd[1]: Finished Set the console keyboard layout.
[ 15.198820] systemd[1]: Reached target Local File Systems (Pre).
[ 15.216979] systemd[1]: Mounting /tmp...
[ 15.241706] systemd[1]: Mounted /tmp.
[ 15.409046] systemd[1]: Started Rule-based Manager for Device Events and Files.
[ 15.466054] systemd[1]: Finished Coldplug All udev Devices.
[ 15.478802] systemd[1]: Starting Show Plymouth Boot Screen...
[ 15.510927] random: crng init done
[ 15.514401] random: 40 urandom warning(s) missed due to ratelimiting
[ 15.534798] systemd[1]: Finished Load/Save Random Seed.
[ 15.549544] systemd[1]: Started Show Plymouth Boot Screen.
[ 15.559570] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch being skipped.
[ 15.571721] systemd[1]: Started Forward Password Requests to Plymouth Directory Watch.
[ 15.581981] systemd[1]: Reached target Local Encrypted Volumes.
[ 15.590599] systemd[1]: Condition check resulted in First Boot Complete being skipped.
[ 15.590787] systemd[1]: Reached target Paths.
[ 15.906115] systemd[1]: Found device /dev/ttyAML0.
[ 15.906168] Registered IR keymap rc-empty
[ 15.915863] rc rc2: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc2
[ 15.916187] rc rc2: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[ 15.917122] input: meson-ir as /devices/platform/soc/c8100000.bus/c8100580.ir/rc/rc2/input2
[ 15.926705] meson-ir c8100580.ir: receiver initialized
[ 15.965207] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[ 16.026997] Bluetooth: Core ver 2.22
[ 16.031452] Bluetooth: Starting self testing
[ 16.062201] systemd[1]: Reached target Hardware activated USB gadget.
[ 16.063995] Bluetooth: ECDH test passed in 27378 usecs
[ 16.104498] debugfs: Directory 'c1105400.audio-controller' with parent 'S905X-P212' already present!
[ 16.121596] Bluetooth: SMP test passed in 18464 usecs
[ 16.126170] Bluetooth: Finished self testing
[ 16.132358] NET: Registered protocol family 31
[ 16.136861] Bluetooth: HCI device and connection manager initialized
[ 16.143822] Bluetooth: HCI socket layer initialized
[ 16.148031] debugfs: Directory 'c1105400.audio-controller' with parent 'S905X-P212' already present!
[ 16.148735] Bluetooth: L2CAP socket layer initialized
[ 16.163018] Bluetooth: SCO socket layer initialized
[ 16.219164] Bluetooth: HCI UART driver ver 2.3
[ 16.232592] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 16.240124] Bluetooth: HCI UART protocol H4 registered
[ 16.244867] Bluetooth: HCI UART protocol BCSP registered
[ 16.274935] Bluetooth: HCI UART protocol LL registered
[ 16.289111] Bluetooth: HCI UART protocol ATH3K registered
[ 16.304539] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 16.320666] Bluetooth: HCI UART protocol Intel registered
[ 16.334476] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator
[ 16.342071] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator
[ 16.352608] Bluetooth: HCI UART protocol Broadcom registered
[ 16.358343] Bluetooth: HCI UART protocol QCA registered
[ 16.363855] Bluetooth: HCI UART protocol AG6XX registered
[ 16.368438] Bluetooth: HCI UART protocol Marvell registered
[ 16.642944] systemd[1]: Found device MassStorageClass BOOT.
[ 16.663611] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[ 16.730724] systemd[1]: Started File System Check Daemon to report status.
[ 16.797246] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ 16.855873] systemd[1]: Reached target Bluetooth.
[ 16.879155] systemd[1]: Starting Load/Save RF Kill Switch Status...
[ 16.949409] systemd[1]: Started Load/Save RF Kill Switch Status.
[ 17.002432] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[ 17.011570] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch being skipped.
[ 17.021082] systemd[1]: Mounting /boot...
[ 17.034180] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 17.035357] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 17.035746] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 17.036762] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 17.037268] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 17.119730] systemd[1]: Mounted /boot.
[ 17.125417] systemd[1]: Reached target Local File Systems.
[ 17.134152] systemd[1]: Condition check resulted in Load AppArmor profiles being skipped.
[ 17.141877] systemd[1]: Starting Armbian ZRAM config...
[ 17.162321] systemd[1]: Started Start/stop the atm daemon(s)..
[ 17.175828] systemd[1]: Starting Set console font and keymap...
[ 17.188993] systemd[1]: Starting Preprocess NFS configuration...
[ 17.202316] systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
[ 17.208853] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[ 17.209107] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[ 17.234018] systemd[1]: Received SIGRTMIN+20 from PID 383 (plymouthd).
[ 17.257503] systemd[1]: Finished Set console font and keymap.
[ 17.282910] systemd[1]: nfs-config.service: Succeeded.
[ 17.290436] systemd[1]: Finished Preprocess NFS configuration.
[ 17.296286] systemd[1]: Condition check resulted in RPC security service for NFS client and server being skipped.
[ 17.296402] systemd[1]: Condition check resulted in RPC security service for NFS server being skipped.
[ 17.296519] systemd[1]: Reached target NFS client services.
[ 17.328305] systemd[1]: atm.service: Main process exited, code=exited, status=1/FAILURE
[ 17.329151] systemd[1]: atm.service: Failed with result 'exit-code'.
[ 17.334595] systemd[1]: Finished Tell Plymouth To Write Out Runtime Data.
[ 17.937792] zram: Added device: zram0
[ 17.944265] zram: Added device: zram1
[ 17.950595] zram: Added device: zram2
[ 18.066440] zram0: detected capacity change from 0 to 482979840
[ 18.137608] Adding 471656k swap on /dev/zram0. Priority:5 extents:1 across:471656k SSFS
[ 18.393771] zram1: detected capacity change from 0 to 52428800
[ 18.486507] systemd[1]: Finished Armbian ZRAM config.
[ 18.506723] systemd[1]: Starting Armbian memory supported logging...
[ 18.610520] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[ 18.617052] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[ 18.617549] Bluetooth: hci0: command 0xfc18 tx timeout
[ 21.962784] systemd[1]: systemd-rfkill.service: Succeeded.
[ 22.335592] systemd[1]: Finished Armbian memory supported logging.
[ 22.375765] systemd[1]: Starting Journal Service...
[ 22.615140] systemd[1]: Started Journal Service.
[ 22.664657] systemd-journald[679]: Received client request to flush runtime journal.
[ 26.720968] Bluetooth: hci0: BCM: failed to write update baudrate (-110)
[ 26.725741] Bluetooth: hci0: Failed to set baudrate
[ 26.958824] meson8b-dwmac c9410000.ethernet eth0: PHY [0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=51)
[ 28.494265] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found
[ 28.503699] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW
[ 28.513769] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode
[ 28.854264] Bluetooth: hci0: command 0x0c03 tx timeout
[ 30.370713] meson8b-dwmac c9410000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 30.377253] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 34.247134] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilte r if you need this.
[ 34.263969] Bridge firewalling registered
[ 36.750939] Bluetooth: hci0: BCM: Reset failed (-110)
[ 105.480726] rc rc2: two consecutive events of type space