forked from hjd1964/OnStepX
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Config.h
378 lines (302 loc) · 37.1 KB
/
Config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
/* ---------------------------------------------------------------------------------------------------------------------------------
* Configuration for OnStepX
*
* For more information on setting OnStep up see http://www.stellarjourney.com/index.php?r=site/equipment_onstep
* and join the OnStep Groups.io at https://groups.io/g/onstep
*
* *** Read the compiler warnings and errors, they are there to help guard against invalid configurations ***
*
* ---------------------------------------------------------------------------------------------------------------------------------
* ADJUST THE FOLLOWING TO CONFIGURE YOUR CONTROLLER FEATURES ----------------------------------------------------------------------
* <-Req'd = always must set, <-Often = usually must set, Option = optional, Adjust = adjust as req'd, Infreq = infrequently changed
*/
// Parameter Name Value Default Notes Hint
// =================================================================================================================================
// CONTROLLER ======================================================================================================================
// PINMAP ------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#PINMAP
#define PINMAP OFF // OFF, Choose from: MiniPCB, MiniPCB2, MaxPCB2, MaxESP3, CNC3, STM32Blue, <-Req'd
// MaxSTM3, FYSETC_S6_2, etc. Other boards and more info. in ~/src/Constants.h
// SERIAL PORT COMMAND CHANNELS --------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#SERIAL_PORTS
#define SERIAL_A_BAUD_DEFAULT 9600 // 9600, n. Where n=9600,19200,57600,115200,230400,460800 (common baud rates.) Infreq
#define SERIAL_B_BAUD_DEFAULT 9600 // 9600, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq
#define SERIAL_B_ESP_FLASHING OFF // OFF, ON Upload ESP8266 WiFi firmware through SERIAL_B with :ESPFLASH# cmd. Option
#define SERIAL_C_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq
#define SERIAL_D_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq
#define SERIAL_E_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq
#define SERIAL_RADIO OFF // OFF, Use BLUETOOTH or WIFI_ACCESS_POINT or WIFI_STATION (ESP32 only.) Option
// STATUS --------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#STATUS_LED
#define STATUS_LED OFF // OFF, Steady illumination if no error, blinks w/error code otherwise. Option
// RETICLE CONTROL ------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#RETICLE_CONTROL
#define RETICLE_LED_DEFAULT OFF // OFF, n. Where n=0..255 (0..100%) activates feature sets default brightness. Option
#define RETICLE_LED_MEMORY OFF // OFF, ON Remember reticle brightness across power cycles. Option
#define RETICLE_LED_INVERT OFF // OFF, ON Inverts control for cases where 0V is max brightness. Option
// WEATHER SENSOR --------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#WEATHER_SENSOR
#define WEATHER OFF // OFF, BME280 (I2C 0x77,) BME280_0x76, BME280_SPI (see pinmap for CS.) Option
// BMP280 (I2C 0x77,) BMP280_0x76, BMP280_SPI (see pinmap for CS.)
// BME280 or BMP280 for temperature, pressure. BME280 for humidity also.
// SIGNALING ------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#SIGNALING
#define STEP_WAVE_FORM SQUARE // SQUARE, PULSE Step signal wave form faster rates. SQUARE best signal integrity. Adjust
// Applies to all axes.
// NON-VOLATILE MEMORY ---------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#NV
#define NV_DRIVER NV_DEFAULT // NV_DEF, Use platforms default non-volatile device to remember runtime settings. Option
// =================================================================================================================================
// MOUNT ===========================================================================================================================
// Driver models (Step/Dir and Servo) many have specific requirements so be sure to follow the link below to help learn about these.
// Typically: A4988, DRV8825, LV8729, S109, TMC2130, TMC5160, TMC2209, etc.
// AXIS1 RA/AZM -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Axes
#define AXIS1_DRIVER_MODEL OFF // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often
// If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM):
// \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/
#define AXIS1_STEPS_PER_DEGREE 12800 // 12800, n. Number of steps per degree: <-Req'd
// n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
#define AXIS1_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often
#define AXIS1_LIMIT_MIN -180 // -180, n. Where n= -90..-360 (degrees.) Minimum "Hour Angle" or Azimuth. Adjust
#define AXIS1_LIMIT_MAX 180 // 180, n. Where n= 90.. 360 (degrees.) Maximum "Hour Angle" or Azimuth. Adjust
#define AXIS1_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. <-Req'd
#define AXIS1_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option
// for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models:
#define AXIS1_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS1_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS1_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option
// /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /
#define AXIS1_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option
#define AXIS1_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq
#define AXIS1_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq
#define AXIS1_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Infreq
#define AXIS1_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from front. Option
#define AXIS1_SENSE_LIMIT_MIN LIMIT_SENSE // ...NSE, HIGH or LOW state on limit sense switch stops movement. Option
#define AXIS1_SENSE_LIMIT_MAX LIMIT_SENSE // ...NSE, HIGH or LOW state on limit sense switch stops movement. Option
// Digital, optionally add: |HYST(n) Where n=0..1023 stability time in ms.
// Analog capable sense inputs also allow adding:
// |THLD(n) Where n=1..1023 (ADU) for Analog threshold.
// |HYST(n) Where n=0..1023 (ADU) for +/- Hystersis range.
// AXIS2 DEC/ALT ------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Axes
#define AXIS2_DRIVER_MODEL OFF // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often
// If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM):
// \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/
#define AXIS2_STEPS_PER_DEGREE 12800 // 12800, n. Number of steps per degree: <-Req'd
// n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
#define AXIS2_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. <-Often
#define AXIS2_LIMIT_MIN -90 // -90, n. Where n=-90..0 (degrees.) Minimum allowed Declination or Altitude. Infreq
#define AXIS2_LIMIT_MAX 90 // 90, n. Where n=0..90 (degrees.) Maximum allowed Declination or Altitude. Infreq
#define AXIS2_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. <-Req'd
#define AXIS2_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option
// for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models:
#define AXIS2_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS2_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS2_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option
// /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /
#define AXIS2_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. Polling for driver status info/fault detection. Option
#define AXIS2_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq
#define AXIS2_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq
#define AXIS2_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Option
#define AXIS2_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from above. Option
#define AXIS2_SENSE_LIMIT_MIN LIMIT_SENSE // ...NSE, HIGH or LOW state on limit sense switch stops movement. Option
#define AXIS2_SENSE_LIMIT_MAX LIMIT_SENSE // ...NSE, HIGH or LOW state on limit sense switch stops movement. Option
// MOUNT -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#MOUNT
#define MOUNT_TYPE GEM // GEM, GEM German Equatorial Mount, etc. that need meridian flips. <-Req'd
// GEM_TA GEM w/tangent arm Declination
// GEM_TAC GEM w/tangent arm Declination and geometry correction
// FORK Fork Mount
// FORK_TA FORK w/tangent arm Declination
// FORK_TAC FORK w/tangent arm Declination and geometry correction
// ALTAZM Altitude/Azimuth Mount, Dobsonians, etc.
// ALTAZM_UNL ALTAZM w/unlimited Azimuth motion
#define MOUNT_COORDS TOPOCENTRIC // ...RIC, Applies refraction to coordinates to/from OnStep, except exactly Infreq
// at the poles. Use TOPO_STRICT to apply refraction even in that case.
// Use OBSERVED_PLACE for no refraction.
#define MOUNT_COORDS_MEMORY OFF // OFF, ON Remembers approximate mount coordinates across power cycles. Option
// Requires FRAM NV memory and the mount must not move while powered down.
#define MOUNT_ENABLE_IN_STANDBY OFF // OFF, ON Enables mount motor drivers while in standby. Infreq
// TIME AND LOCATION ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#TLS
#define TIME_LOCATION_SOURCE OFF // OFF, DS3231 (I2C,) SD3031 (I2C,) TEENSY (T3.2 etc,) GPS, or NTP source. Option
// Provides Date/Time, and if available, PPS & Lat/Long also.
#define TIME_LOCATION_PPS_SENSE OFF // OFF, HIGH senses PPS (pulse per second,) signal rising edge, or use LOW for Option
// falling edge, or use BOTH for rising and falling edges.
// STATUS ------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/Configuration_Mount#STATUS
#define STATUS_MOUNT_LED OFF // OFF, ON Flashes proportional to rate of movement or solid on for slews. Option
#define STATUS_BUZZER OFF // OFF, ON, n. Where n=100..6000 (Hz freq.) for speaker. ON for piezo buzzer. Option
#define STATUS_BUZZER_DEFAULT OFF // OFF, ON starts w/buzzer sound enabled. Option
#define STATUS_BUZZER_MEMORY OFF // OFF, ON to remember buzzer sound setting across power cycles. Option
// ST4 INTERFACE -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#ST4
// *** It is up to you to verify the interface meets the electrical specifications of any connected device, use at your own risk ***
#define ST4_INTERFACE OFF // OFF, ON enables interface. <= 1X guides unless hand control mode. Option
// During goto btn press: aborts slew or continue meridian flip pause home
#define ST4_HAND_CONTROL ON // ON, ON for hand controller special features and SHC support. Option
// Hold [E]+[W] btns >2s: Guide rate [E]- [W]+ [N] trk on/off [S] sync
// Hold [N]+[S] btns >2s: Usr cat item [E]- [W]+ [N] goto [S] snd on/off
#define ST4_HAND_CONTROL_FOCUSER ON // ON, ON alternate to above: Focuser move [E]f1 [W]f2 [N]- [S]+ Option
// GUIDING BEHAVIOUR ------------------------------------------ see https://onstep.groups.io/g/main/wiki/Configuration_Mount#GUIDING
#define GUIDE_TIME_LIMIT 10 // 10, n. Time limit n=0..120 seconds. Use 0 to disable. Adjust
#define GUIDE_DISABLE_BACKLASH OFF // OFF, Disable backlash takeup during guiding at <= 1X. Option
// LIMITS ------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/Configuration_Mount#LIMITS
#define LIMIT_SENSE OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option
#define LIMIT_STRICT OFF // OFF, disables limits until unpark goto or sync. ON enables limits at startup. Option
// note that ON also disables all motion until date/time are set.
// PARKING ---------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#PARKING
#define PARK_SENSE OFF // OFF, HIGH or LOW state indicates mount is in the park orientation. Option
#define PARK_SIGNAL OFF // OFF, HIGH or LOW state park input signal triggers parking. Option
#define PARK_STATUS OFF // OFF, signals with a HIGH or LOW state when successfully parked. Option
#define PARK_STRICT OFF // OFF, ON Un-parking is only allowed if successfully parked. Option
// PEC ------------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/Configuration_Mount#PEC
#define PEC_STEPS_PER_WORM_ROTATION 0 // 0, n. Steps per worm rotation (0 disables else 720 sec buffer allocated.) <-Req'd
// n = (AXIS1_STEPS_PER_DEGREE*360)/reduction_final_stage
#define PEC_SENSE OFF // OFF, HIGH. Senses the PEC signal rising edge or use LOW for falling edge. Option
// Ignored in ALTAZM mode.
#define PEC_BUFFER_SIZE_LIMIT 720 // 720, Seconds of PEC buffer allowed. Infreq
// TRACKING BEHAVIOUR ---------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#TRACKING
#define TRACK_BACKLASH_RATE 20 // 20, n. Where n=2..50 (x sidereal rate) during backlash takeup. Option
// Too fast motors stall/gears slam or too slow and sluggish in backlash.
#define TRACK_AUTOSTART OFF // OFF, ON Start with tracking enabled. Option
#define TRACK_COMPENSATION_DEFAULT OFF // OFF, No compensation or REFRACTION, REFRACTION_DUAL, MODEL, MODEL_DUAL. Option
#define TRACK_COMPENSATION_MEMORY OFF // OFF, ON Remembers refraction/pointing model compensated tracking settings. Option
// SLEWING BEHAVIOUR ------------------------------------------ see https://onstep.groups.io/g/main/wiki/Configuration_Mount#SLEWING
#define SLEW_RATE_BASE_DESIRED 1.0 // 1.0, n. Desired slew rate in deg/sec. Adjustable at run-time from <-Req'd
// 1/2 to 2x this rate, and as performace considerations require.
#define SLEW_RATE_MEMORY OFF // OFF, ON Remembers rates set across power cycles. Option
#define SLEW_ACCELERATION_DIST 5.0 // 5.0, n, (degrees.) Approx. distance for acceleration (and deceleration.) Adjust
#define SLEW_RAPID_STOP_DIST 2.0 // 2.0, n, (degrees.) Approx. distance required to stop when a slew Adjust
// is aborted or a limit is exceeded.
#define GOTO_FEATURE ON // ON, Use OFF to disable mount Goto features. Infreq
#define GOTO_OFFSET 0.25 // 0.25, Offset in deg's for goto target unidirectional approach, 0.0 disables Adjust
#define GOTO_OFFSET_ALIGN OFF // OFF, ON skips final phase of goto for align stars so user tends to approach Option
// from the correct direction when centering.
// PIER SIDE BEHAVIOUR --------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#PIERSIDE
#define MFLIP_SKIP_HOME OFF // OFF, ON Goto directly to the destination without visiting home position. Option
#define MFLIP_AUTOMATIC_DEFAULT OFF // OFF, ON Start with automatic meridian flips enabled. Option
#define MFLIP_AUTOMATIC_MEMORY OFF // OFF, ON Remember automatic meridian flip setting across power cycles. Option
#define MFLIP_PAUSE_HOME_DEFAULT OFF // OFF, ON Start with meridian flip pause at home enabed. Infreq
#define MFLIP_PAUSE_HOME_MEMORY OFF // OFF, ON Remember meridian flip pause at home setting across power cycles. Infreq
#define PIER_SIDE_SYNC_CHANGE_SIDES OFF // OFF, ON Allows sync to change pier side, for GEM mounts. Option
#define PIER_SIDE_PREFERRED_DEFAULT BEST // BEST, BEST Stays on current side if possible. EAST or WEST switch if possible. Option
#define PIER_SIDE_PREFERRED_MEMORY OFF // OFF, ON Remember preferred pier side setting across power cycles. Option
// ALIGN -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Mount#ALIGN
#define ALIGN_AUTO_HOME OFF // OFF, ON uses home switches to find home first when starting an align. Option
#define ALIGN_MODEL_MEMORY OFF // OFF, ON Restores any pointing model saved in NV at startup. Option
#define ALIGN_MAX_STARS AUTO // AUTO, Uses HAL specified default (either 6 or 9 stars.) Infreq
// Or use n. Where n=1 (for Sync only) or 3 to 9 (for Goto Assist.)
// =================================================================================================================================
// ROTATOR =========================================================================================================================
// Driver models (Step/Dir and Servo) many have specific requirements so be sure to follow the link below to help learn about these.
// Typically: A4988, DRV8825, LV8729, S109, TMC2130S, etc.
// AXIS3 ROTATOR ---------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Rotator
#define AXIS3_DRIVER_MODEL OFF // OFF, Enter motor driver model (above) to activate the rotator. Option
#define AXIS3_SLEW_RATE_BASE_DESIRED 1.0 // 1.0, n. Desired slew rate in deg/sec. Adjustable at run-time from <-Req'd
// 1/2 to 2x this rate, and as performance considerations require.
// If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM):
// \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/
#define AXIS3_STEPS_PER_DEGREE 64.0 // 64.0, n. Number of steps per degree for rotator/de-rotator. Adjust
// Alt/Az de-rotation: n = (num_circumference_pixels * 2)/360, minimum
#define AXIS3_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option
#define AXIS3_LIMIT_MIN 0 // 0, n. Where n=-360..0 (degrees.) Minimum allowed rotator angle. Infreq
#define AXIS3_LIMIT_MAX 360 // 360, n. Where n=0..360 (degrees.) Maximum allowed rotator angle. Infreq
#define AXIS3_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. Option
#define AXIS3_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option
// for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models:
#define AXIS3_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS3_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS3_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option
// /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /
#define AXIS3_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option
#define AXIS3_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq
#define AXIS3_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq
#define AXIS3_POWER_DOWN OFF // OFF, ON Powers off 30 seconds after movement stops. Option
#define AXIS3_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from above. Option
#define AXIS3_SENSE_LIMIT_MIN OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option
#define AXIS3_SENSE_LIMIT_MAX OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option
// =================================================================================================================================
// FOCUSERS ========================================================================================================================
// Driver models (Step/Dir and Servo) many have specific requirements so be sure to follow the link below to help learn about these.
// Typically: A4988, DRV8825, LV8729, S109, TMC2130S, etc.
// AXIS4 FOCUSER 1 -------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Focuser
#define AXIS4_DRIVER_MODEL OFF // OFF, Enter motor driver model (above) to activate the focuser. Option
#define AXIS4_SLEW_RATE_BASE_DESIRED 500 // 500, n, Where n=200..5000 (um/s.) Adjustable at run-time from <-Req'd
// 1/2 to 2x this rate, and as performance considerations require.
#define AXIS4_SLEW_RATE_MINIMUM 20 // 20, n. Where n=5..200 (um/s.) Minimum microns/second. Adjust
// If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM):
// \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/
#define AXIS4_STEPS_PER_MICRON 0.5 // 0.5, n. Steps per micrometer. Figure this out by testing or other means. Adjust
#define AXIS4_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option
#define AXIS4_LIMIT_MIN 0 // 0, n. Where n=0..500 (millimeters.) Minimum allowed position. Adjust
#define AXIS4_LIMIT_MAX 50 // 50, n. Where n=0..500 (millimeters.) Maximum allowed position. Adjust
#define AXIS4_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. Option
#define AXIS4_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option
// for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models:
#define AXIS4_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option
#define AXIS4_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option
#define AXIS4_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option
// /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /
#define AXIS4_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option
#define AXIS4_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq
#define AXIS4_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq
#define AXIS4_POWER_DOWN OFF // OFF, ON Powers off 30 seconds after movement stops. Option
#define AXIS4_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from above. Option
#define AXIS4_SENSE_LIMIT_MIN OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option
#define AXIS4_SENSE_LIMIT_MAX OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option
// AXIS5 FOCUSER 2 -----------------------------------------------------------------------------------------------------------------
// Up to 6 focusers can be present (AXIS4 to AXIS9) simply copy the above text for focuser 1 and rename to AXIS5_ for focuser 2, etc
// FOCUSER TEMPERATURE ---------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Focuser
#define FOCUSER_TEMPERATURE OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n for focuser temp. Adjust
// =================================================================================================================================
// AUXILIARY FEATURES ==============================================================================================================
// FEATURES ------------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Aux
// Note: Temporarily set DEBUG mode to VERBOSE and use "FEATURE1_TEMP DS1820" to list the DS18B20 device serial numbers.
#define FEATURE1_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE1_NAME "FEATURE1" // "FE..", Name of feature being controlled. Adjust
#define FEATURE1_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE1_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE1_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE1_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE1_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE2_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE2_NAME "FEATURE2" // "FE..", Name of feature being controlled. Adjust
#define FEATURE2_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE2_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE2_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE2_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE2_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE3_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE3_NAME "FEATURE3" // "FE..", Name of feature being controlled. Adjust
#define FEATURE3_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE3_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE3_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE3_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE3_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE4_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE4_NAME "FEATURE4" // "FE..", Name of feature being controlled. Adjust
#define FEATURE4_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE4_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE4_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE4_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE4_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE5_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE5_NAME "FEATURE5" // "FE..", Name of feature being controlled. Adjust
#define FEATURE5_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE5_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE5_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE5_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE5_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE6_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE6_NAME "FEATURE6" // "FE..", Name of feature being controlled. Adjust
#define FEATURE6_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE6_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE6_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE6_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE6_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE7_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE7_NAME "FEATURE7" // "FE..", Name of feature being controlled. Adjust
#define FEATURE7_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE7_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE7_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE7_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE7_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
#define FEATURE8_PURPOSE OFF // OFF, SWITCH, MOMENTARY_SWITCH, ANALOG_OUT, DEW_HEATER, INTERVALOMETER. Option
#define FEATURE8_NAME "FEATURE8" // "FE..", Name of feature being controlled. Adjust
#define FEATURE8_TEMP OFF // OFF, THERMISTOR or n. Where n is the ds18b20 s/n. For DEW_HEATER temperature. Adjust
#define FEATURE8_PIN OFF // OFF, AUX for auxiliary pin, n. Where n is the pin#. Adjust
#define FEATURE8_VALUE_DEFAULT OFF // OFF, ON, n. Where n=0..255 for ANALOG_OUT purpose. Adjust
#define FEATURE8_VALUE_MEMORY OFF // OFF, ON remembers SWITCH, ANALOG_OUT, DEW_HEATER state across power cycles. Adjust
#define FEATURE8_ON_STATE HIGH // HIGH, LOW to invert so "ON" is 0V and "OFF" is Vcc (3.3V usually.) Adjust
// ---------------------------------------------------------------------------------------------------------------------------------
#define FileVersionConfig 6
#include "Extended.config.h"