Adafruit_NeoPixel.cpp

/*!
 * @file Adafruit_NeoPixel.cpp
 *
 * @mainpage Arduino Library for driving Adafruit NeoPixel addressable LEDs,
 * FLORA RGB Smart Pixels and compatible devicess -- WS2811, WS2812, WS2812B,
 * SK6812, etc.
 *
 * @section intro_sec Introduction
 *
 * This is the documentation for Adafruit's NeoPixel library for the
 * Arduino platform, allowing a broad range of microcontroller boards
 * (most AVR boards, many ARM devices, ESP8266 and ESP32, among others)
 * to control Adafruit NeoPixels, FLORA RGB Smart Pixels and compatible
 * devices -- WS2811, WS2812, WS2812B, SK6812, etc.
 *
 * Adafruit invests time and resources providing this open source code,
 * please support Adafruit and open-source hardware by purchasing products
 * from Adafruit!
 *
 * @section author Author
 *
 * Written by Phil "Paint Your Dragon" Burgess for Adafruit Industries,
 * with contributions by PJRC, Michael Miller and other members of the
 * open source community.
 *
 * @section license License
 *
 * This file is part of the Adafruit_NeoPixel library.
 *
 * Adafruit_NeoPixel is free software: you can redistribute it and/or
 * modify it under the terms of the GNU Lesser General Public License as
 * published by the Free Software Foundation, either version 3 of the
 * License, or (at your option) any later version.
 *
 * Adafruit_NeoPixel is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 * GNU Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public
 * License along with NeoPixel. If not, see
 * <http://www.gnu.org/licenses/>.
 *
 */

#include "Adafruit_NeoPixel.h"

#if defined(TARGET_LPC1768)
#include <time.h>
#endif

#if defined(NRF52) || defined(NRF52_SERIES)
#include "nrf.h"

// Interrupt is only disabled if there is no PWM device available
// Note: Adafruit Bluefruit nrf52 does not use this option
//#define NRF52_DISABLE_INT
#endif

/*!
  @brief   NeoPixel constructor when length, pin and pixel type are known
           at compile-time.
  @param   n  Number of NeoPixels in strand.
  @param   p  Arduino pin number which will drive the NeoPixel data in.
  @param   t  Pixel type -- add together NEO_* constants defined in
              Adafruit_NeoPixel.h, for example NEO_GRB+NEO_KHZ800 for
              NeoPixels expecting an 800 KHz (vs 400 KHz) data stream
              with color bytes expressed in green, red, blue order per
              pixel.
  @return  Adafruit_NeoPixel object. Call the begin() function before use.
*/
Adafruit_NeoPixel::Adafruit_NeoPixel(uint16_t n, uint16_t p, neoPixelType t) : begun(false), brightness(0), pixels(NULL), endTime(0)
{
  updateType(t);
  updateLength(n);
  setPin(p);
}

/*!
  @brief   "Empty" NeoPixel constructor when length, pin and/or pixel type
           are not known at compile-time, and must be initialized later with
           updateType(), updateLength() and setPin().
  @return  Adafruit_NeoPixel object. Call the begin() function before use.
  @note    This function is deprecated, here only for old projects that
           may still be calling it. New projects should instead use the
           'new' keyword with the first constructor syntax (length, pin,
           type).
*/
Adafruit_NeoPixel::Adafruit_NeoPixel() :
#if defined(NEO_KHZ400)
                                         is800KHz(true),
#endif
                                         begun(false), numLEDs(0), numBytes(0), pin(-1), brightness(0), pixels(NULL),
                                         rOffset(1), gOffset(0), bOffset(2), wOffset(1), endTime(0)
{
}

/*!
  @brief   Deallocate Adafruit_NeoPixel object, set data pin back to INPUT.
*/
Adafruit_NeoPixel::~Adafruit_NeoPixel()
{
  free(pixels);
  if (pin >= 0)
    pinMode(pin, INPUT);
}

/*!
  @brief   Configure NeoPixel pin for output.
*/
void Adafruit_NeoPixel::begin(void)
{
  if (pin >= 0)
  {
    pinMode(pin, OUTPUT);
    digitalWrite(pin, LOW);
  }
  begun = true;
}

/*!
  @brief   Change the length of a previously-declared Adafruit_NeoPixel
           strip object. Old data is deallocated and new data is cleared.
           Pin number and pixel format are unchanged.
  @param   n  New length of strip, in pixels.
  @note    This function is deprecated, here only for old projects that
           may still be calling it. New projects should instead use the
           'new' keyword with the first constructor syntax (length, pin,
           type).
*/
void Adafruit_NeoPixel::updateLength(uint16_t n)
{
  free(pixels); // Free existing data (if any)

  // Allocate new data -- note: ALL PIXELS ARE CLEARED
  numBytes = n * ((wOffset == rOffset) ? 3 : 4);
  if ((pixels = (uint8_t *)malloc(numBytes)))
  {
    memset(pixels, 0, numBytes);
    numLEDs = n;
  }
  else
  {
    numLEDs = numBytes = 0;
  }
}

/*!
  @brief   Change the pixel format of a previously-declared
           Adafruit_NeoPixel strip object. If format changes from one of
           the RGB variants to an RGBW variant (or RGBW to RGB), the old
           data will be deallocated and new data is cleared. Otherwise,
           the old data will remain in RAM and is not reordered to the
           new format, so it's advisable to follow up with clear().
  @param   t  Pixel type -- add together NEO_* constants defined in
              Adafruit_NeoPixel.h, for example NEO_GRB+NEO_KHZ800 for
              NeoPixels expecting an 800 KHz (vs 400 KHz) data stream
              with color bytes expressed in green, red, blue order per
              pixel.
  @note    This function is deprecated, here only for old projects that
           may still be calling it. New projects should instead use the
           'new' keyword with the first constructor syntax
           (length, pin, type).
*/
void Adafruit_NeoPixel::updateType(neoPixelType t)
{
  bool oldThreeBytesPerPixel = (wOffset == rOffset); // false if RGBW

  wOffset = (t >> 6) & 0b11; // See notes in header file
  rOffset = (t >> 4) & 0b11; // regarding R/G/B/W offsets
  gOffset = (t >> 2) & 0b11;
  bOffset = t & 0b11;
#if defined(NEO_KHZ400)
  is800KHz = (t < 256); // 400 KHz flag is 1<<8
#endif

  // If bytes-per-pixel has changed (and pixel data was previously
  // allocated), re-allocate to new size. Will clear any data.
  if (pixels)
  {
    bool newThreeBytesPerPixel = (wOffset == rOffset);
    if (newThreeBytesPerPixel != oldThreeBytesPerPixel)
      updateLength(numLEDs);
  }
}

#if defined(ESP8266)
// ESP8266 show() is external to enforce ICACHE_RAM_ATTR execution
extern "C" void ICACHE_RAM_ATTR espShow(
    uint16_t pin, uint8_t *pixels, uint32_t numBytes, uint8_t type);
#elif defined(ESP32)
extern "C" void espShow(
    uint16_t pin, uint8_t *pixels, uint32_t numBytes, uint8_t type);
#endif // ESP8266

/*!
  @brief   Transmit pixel data in RAM to NeoPixels.
  @note    On most architectures, interrupts are temporarily disabled in
           order to achieve the correct NeoPixel signal timing. This means
           that the Arduino millis() and micros() functions, which require
           interrupts, will lose small intervals of time whenever this
           function is called (about 30 microseconds per RGB pixel, 40 for
           RGBW pixels). There's no easy fix for this, but a few
           specialized alternative or companion libraries exist that use
           very device-specific peripherals to work around it.
*/
void Adafruit_NeoPixel::show(void)
{

  if (!pixels)
    return;

  // Data latch = 300+ microsecond pause in the output stream. Rather than
  // put a delay at the end of the function, the ending time is noted and
  // the function will simply hold off (if needed) on issuing the
  // subsequent round of data until the latch time has elapsed. This
  // allows the mainline code to start generating the next frame of data
  // rather than stalling for the latch.
  while (!canShow())
    ;
    // endTime is a private member (rather than global var) so that multiple
    // instances on different pins can be quickly issued in succession (each
    // instance doesn't delay the next).

    // In order to make this code runtime-configurable to work with any pin,
    // SBI/CBI instructions are eschewed in favor of full PORT writes via the
    // OUT or ST instructions. It relies on two facts: that peripheral
    // functions (such as PWM) take precedence on output pins, so our PORT-
    // wide writes won't interfere, and that interrupts are globally disabled
    // while data is being issued to the LEDs, so no other code will be
    // accessing the PORT. The code takes an initial 'snapshot' of the PORT
    // state, computes 'pin high' and 'pin low' values, and writes these back
    // to the PORT register as needed.

    // NRF52 may use PWM + DMA (if available), may not need to disable interrupt
#if !(defined(NRF52) || defined(NRF52_SERIES))
  noInterrupts(); // Need 100% focus on instruction timing
#endif

#if defined(__AVR__)
  // AVR MCUs -- ATmega & ATtiny (no XMEGA) ---------------------------------

  volatile uint16_t
      i = numBytes; // Loop counter
  volatile uint8_t
      *ptr = pixels, // Pointer to next byte
      b = *ptr++,    // Current byte value
      hi,            // PORT w/output bit set high
      lo;            // PORT w/output bit set low

  // Hand-tuned assembly code issues data to the LED drivers at a specific
  // rate. There's separate code for different CPU speeds (8, 12, 16 MHz)
  // for both the WS2811 (400 KHz) and WS2812 (800 KHz) drivers. The
  // datastream timing for the LED drivers allows a little wiggle room each
  // way (listed in the datasheets), so the conditions for compiling each
  // case are set up for a range of frequencies rather than just the exact
  // 8, 12 or 16 MHz values, permitting use with some close-but-not-spot-on
  // devices (e.g. 16.5 MHz DigiSpark). The ranges were arrived at based
  // on the datasheet figures and have not been extensively tested outside
  // the canonical 8/12/16 MHz speeds; there's no guarantee these will work
  // close to the extremes (or possibly they could be pushed further).
  // Keep in mind only one CPU speed case actually gets compiled; the
  // resulting program isn't as massive as it might look from source here.

// 8 MHz(ish) AVR ---------------------------------------------------------
#if (F_CPU >= 7400000UL) && (F_CPU <= 9500000UL)

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif

    volatile uint8_t n1, n2 = 0; // First, next bits out

    // Squeezing an 800 KHz stream out of an 8 MHz chip requires code
    // specific to each PORT register.

    // 10 instruction clocks per bit: HHxxxxxLLL
    // OUT instructions:              ^ ^    ^   (T=0,2,7)

    // PORTD OUTPUT ----------------------------------------------------

#if defined(PORTD)
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
    if (port == &PORTD)
    {
#endif // defined(PORTB/C/F)

      hi = PORTD | pinMask;
      lo = PORTD & ~pinMask;
      n1 = lo;
      if (b & 0x80)
        n1 = hi;

      // Dirty trick: RJMPs proceeding to the next instruction are used
      // to delay two clock cycles in one instruction word (rather than
      // using two NOPs). This was necessary in order to squeeze the
      // loop down to exactly 64 words -- the maximum possible for a
      // relative branch.

      asm volatile(
          "headD:"
          "\n\t" // Clk  Pseudocode
                 // Bit 7:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n2]   , %[lo]"
          "\n\t" // 1    n2   = lo
          "out  %[port] , %[n1]"
          "\n\t" // 1    PORT = n1
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 6"
          "\n\t" // 1-2  if(b & 0x40)
          "mov %[n2]   , %[hi]"
          "\n\t" // 0-1   n2 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 6:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n1]   , %[lo]"
          "\n\t" // 1    n1   = lo
          "out  %[port] , %[n2]"
          "\n\t" // 1    PORT = n2
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 5"
          "\n\t" // 1-2  if(b & 0x20)
          "mov %[n1]   , %[hi]"
          "\n\t" // 0-1   n1 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 5:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n2]   , %[lo]"
          "\n\t" // 1    n2   = lo
          "out  %[port] , %[n1]"
          "\n\t" // 1    PORT = n1
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 4"
          "\n\t" // 1-2  if(b & 0x10)
          "mov %[n2]   , %[hi]"
          "\n\t" // 0-1   n2 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 4:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n1]   , %[lo]"
          "\n\t" // 1    n1   = lo
          "out  %[port] , %[n2]"
          "\n\t" // 1    PORT = n2
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 3"
          "\n\t" // 1-2  if(b & 0x08)
          "mov %[n1]   , %[hi]"
          "\n\t" // 0-1   n1 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 3:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n2]   , %[lo]"
          "\n\t" // 1    n2   = lo
          "out  %[port] , %[n1]"
          "\n\t" // 1    PORT = n1
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 2"
          "\n\t" // 1-2  if(b & 0x04)
          "mov %[n2]   , %[hi]"
          "\n\t" // 0-1   n2 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 2:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n1]   , %[lo]"
          "\n\t" // 1    n1   = lo
          "out  %[port] , %[n2]"
          "\n\t" // 1    PORT = n2
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 1"
          "\n\t" // 1-2  if(b & 0x02)
          "mov %[n1]   , %[hi]"
          "\n\t" // 0-1   n1 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "rjmp .+0"
          "\n\t" // 2    nop nop
          // Bit 1:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n2]   , %[lo]"
          "\n\t" // 1    n2   = lo
          "out  %[port] , %[n1]"
          "\n\t" // 1    PORT = n1
          "rjmp .+0"
          "\n\t" // 2    nop nop
          "sbrc %[byte] , 0"
          "\n\t" // 1-2  if(b & 0x01)
          "mov %[n2]   , %[hi]"
          "\n\t" // 0-1   n2 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "sbiw %[count], 1"
          "\n\t" // 2    i-- (don't act on Z flag yet)
          // Bit 0:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi
          "mov  %[n1]   , %[lo]"
          "\n\t" // 1    n1   = lo
          "out  %[port] , %[n2]"
          "\n\t" // 1    PORT = n2
          "ld   %[byte] , %a[ptr]+"
          "\n\t" // 2    b = *ptr++
          "sbrc %[byte] , 7"
          "\n\t" // 1-2  if(b & 0x80)
          "mov %[n1]   , %[hi]"
          "\n\t" // 0-1   n1 = hi
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo
          "brne headD"
          "\n" // 2    while(i) (Z flag set above)
          : [byte] "+r"(b),
            [n1] "+r"(n1),
            [n2] "+r"(n2),
            [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTD)),
            [ptr] "e"(ptr),
            [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTB) || defined(PORTC) || defined(PORTF)
    }
    else // other PORT(s)
#endif   // defined(PORTB/C/F)
#endif   // defined(PORTD)

    // PORTB OUTPUT ----------------------------------------------------

#if defined(PORTB)
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
        if (port == &PORTB)
    {
#endif // defined(PORTD/C/F)

      // Same as above, just switched to PORTB and stripped of comments.
      hi = PORTB | pinMask;
      lo = PORTB & ~pinMask;
      n1 = lo;
      if (b & 0x80)
        n1 = hi;

      asm volatile(
          "headB:"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 6"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 5"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 4"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 3"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 2"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 1"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 0"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "brne headB"
          "\n"
          : [byte] "+r"(b), [n1] "+r"(n1), [n2] "+r"(n2), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTB)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTC) || defined(PORTF)
    }
#endif
#if defined(PORTC) || defined(PORTF)
    else
#endif // defined(PORTC/F)
#endif // defined(PORTB)

    // PORTC OUTPUT ----------------------------------------------------

#if defined(PORTC)
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
        if (port == &PORTC)
    {
#endif // defined(PORTD/B/F)

      // Same as above, just switched to PORTC and stripped of comments.
      hi = PORTC | pinMask;
      lo = PORTC & ~pinMask;
      n1 = lo;
      if (b & 0x80)
        n1 = hi;

      asm volatile(
          "headC:"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 6"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 5"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 4"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 3"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 2"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 1"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 0"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "brne headC"
          "\n"
          : [byte] "+r"(b), [n1] "+r"(n1), [n2] "+r"(n2), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTC)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTB) || defined(PORTF)
    }
#endif // defined(PORTD/B/F)
#if defined(PORTF)
    else
#endif
#endif // defined(PORTC)

    // PORTF OUTPUT ----------------------------------------------------

#if defined(PORTF)
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
        if (port == &PORTF)
    {
#endif // defined(PORTD/B/C)

      hi = PORTF | pinMask;
      lo = PORTF & ~pinMask;
      n1 = lo;
      if (b & 0x80)
        n1 = hi;

      asm volatile(
          "headF:"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 6"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 5"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 4"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 3"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 2"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 1"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n2]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n1]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "sbrc %[byte] , 0"
          "\n\t"
          "mov %[n2]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "mov  %[n1]   , %[lo]"
          "\n\t"
          "out  %[port] , %[n2]"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[n1]   , %[hi]"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "brne headF"
          "\n"
          : [byte] "+r"(b), [n1] "+r"(n1), [n2] "+r"(n2), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTF)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTB) || defined(PORTC)
    }
#endif // defined(PORTD/B/C)
#endif // defined(PORTF)

#if defined(NEO_KHZ400)
  }
  else
  { // end 800 KHz, do 400 KHz

    // Timing is more relaxed; unrolling the inner loop for each bit is
    // not necessary. Still using the peculiar RJMPs as 2X NOPs, not out
    // of need but just to trim the code size down a little.
    // This 400-KHz-datastream-on-8-MHz-CPU code is not quite identical
    // to the 800-on-16 code later -- the hi/lo timing between WS2811 and
    // WS2812 is not simply a 2:1 scale!

    // 20 inst. clocks per bit: HHHHxxxxxxLLLLLLLLLL
    // ST instructions:         ^   ^     ^          (T=0,4,10)

    volatile uint8_t next, bit;

    hi = *port | pinMask;
    lo = *port & ~pinMask;
    next = lo;
    bit = 8;

    asm volatile(
        "head20:"
        "\n\t" // Clk  Pseudocode    (T =  0)
        "st   %a[port], %[hi]"
        "\n\t" // 2    PORT = hi     (T =  2)
        "sbrc %[byte] , 7"
        "\n\t" // 1-2  if(b & 128)
        "mov  %[next], %[hi]"
        "\n\t" // 0-1   next = hi    (T =  4)
        "st   %a[port], %[next]"
        "\n\t" // 2    PORT = next   (T =  6)
        "mov  %[next] , %[lo]"
        "\n\t" // 1    next = lo     (T =  7)
        "dec  %[bit]"
        "\n\t" // 1    bit--         (T =  8)
        "breq nextbyte20"
        "\n\t" // 1-2  if(bit == 0)
        "rol  %[byte]"
        "\n\t" // 1    b <<= 1       (T = 10)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 12)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 14)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 16)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 18)
        "rjmp head20"
        "\n\t" // 2    -> head20 (next bit out)
        "nextbyte20:"
        "\n\t" //                    (T = 10)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 12)
        "nop"
        "\n\t" // 1    nop           (T = 13)
        "ldi  %[bit]  , 8"
        "\n\t" // 1    bit = 8       (T = 14)
        "ld   %[byte] , %a[ptr]+"
        "\n\t" // 2    b = *ptr++    (T = 16)
        "sbiw %[count], 1"
        "\n\t" // 2    i--           (T = 18)
        "brne head20"
        "\n" // 2    if(i != 0) -> (next byte)
        : [port] "+e"(port),
          [byte] "+r"(b),
          [bit] "+r"(bit),
          [next] "+r"(next),
          [count] "+w"(i)
        : [hi] "r"(hi),
          [lo] "r"(lo),
          [ptr] "e"(ptr));
  }
#endif // NEO_KHZ400

// 12 MHz(ish) AVR --------------------------------------------------------
#elif (F_CPU >= 11100000UL) && (F_CPU <= 14300000UL)

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif

    // In the 12 MHz case, an optimized 800 KHz datastream (no dead time
    // between bytes) requires a PORT-specific loop similar to the 8 MHz
    // code (but a little more relaxed in this case).

    // 15 instruction clocks per bit: HHHHxxxxxxLLLLL
    // OUT instructions:              ^   ^     ^     (T=0,4,10)

    volatile uint8_t next;

    // PORTD OUTPUT ----------------------------------------------------

#if defined(PORTD)
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
    if (port == &PORTD)
    {
#endif // defined(PORTB/C/F)

      hi = PORTD | pinMask;
      lo = PORTD & ~pinMask;
      next = lo;
      if (b & 0x80)
        next = hi;

      // Don't "optimize" the OUT calls into the bitTime subroutine;
      // we're exploiting the RCALL and RET as 3- and 4-cycle NOPs!
      asm volatile(
          "headD:"
          "\n\t" //        (T =  0)
          "out   %[port], %[hi]"
          "\n\t" //        (T =  1)
          "rcall bitTimeD"
          "\n\t" // Bit 7  (T = 15)
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 6
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 5
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 4
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 3
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 2
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeD"
          "\n\t" // Bit 1
          // Bit 0:
          "out  %[port] , %[hi]"
          "\n\t" // 1    PORT = hi    (T =  1)
          "rjmp .+0"
          "\n\t" // 2    nop nop      (T =  3)
          "ld   %[byte] , %a[ptr]+"
          "\n\t" // 2    b = *ptr++   (T =  5)
          "out  %[port] , %[next]"
          "\n\t" // 1    PORT = next  (T =  6)
          "mov  %[next] , %[lo]"
          "\n\t" // 1    next = lo    (T =  7)
          "sbrc %[byte] , 7"
          "\n\t" // 1-2  if(b & 0x80) (T =  8)
          "mov %[next] , %[hi]"
          "\n\t" // 0-1    next = hi  (T =  9)
          "nop"
          "\n\t" // 1                 (T = 10)
          "out  %[port] , %[lo]"
          "\n\t" // 1    PORT = lo    (T = 11)
          "sbiw %[count], 1"
          "\n\t" // 2    i--          (T = 13)
          "brne headD"
          "\n\t" // 2    if(i != 0) -> (next byte)
          "rjmp doneD"
          "\n\t"
          "bitTimeD:"
          "\n\t" //      nop nop nop     (T =  4)
          "out  %[port], %[next]"
          "\n\t" // 1    PORT = next     (T =  5)
          "mov  %[next], %[lo]"
          "\n\t" // 1    next = lo       (T =  6)
          "rol  %[byte]"
          "\n\t" // 1    b <<= 1         (T =  7)
          "sbrc %[byte], 7"
          "\n\t" // 1-2  if(b & 0x80)    (T =  8)
          "mov %[next], %[hi]"
          "\n\t" // 0-1   next = hi      (T =  9)
          "nop"
          "\n\t" // 1                    (T = 10)
          "out  %[port], %[lo]"
          "\n\t" // 1    PORT = lo       (T = 11)
          "ret"
          "\n\t" // 4    nop nop nop nop (T = 15)
          "doneD:"
          "\n"
          : [byte] "+r"(b),
            [next] "+r"(next),
            [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTD)),
            [ptr] "e"(ptr),
            [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTB) || defined(PORTC) || defined(PORTF)
    }
    else // other PORT(s)
#endif // defined(PORTB/C/F)
#endif // defined(PORTD)

    // PORTB OUTPUT ----------------------------------------------------

#if defined(PORTB)
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
        if (port == &PORTB)
    {
#endif // defined(PORTD/C/F)

      hi = PORTB | pinMask;
      lo = PORTB & ~pinMask;
      next = lo;
      if (b & 0x80)
        next = hi;

      // Same as above, just set for PORTB & stripped of comments
      asm volatile(
          "headB:"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeB"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "out  %[port] , %[next]"
          "\n\t"
          "mov  %[next] , %[lo]"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[next] , %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "brne headB"
          "\n\t"
          "rjmp doneB"
          "\n\t"
          "bitTimeB:"
          "\n\t"
          "out  %[port], %[next]"
          "\n\t"
          "mov  %[next], %[lo]"
          "\n\t"
          "rol  %[byte]"
          "\n\t"
          "sbrc %[byte], 7"
          "\n\t"
          "mov %[next], %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port], %[lo]"
          "\n\t"
          "ret"
          "\n\t"
          "doneB:"
          "\n"
          : [byte] "+r"(b), [next] "+r"(next), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTB)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTC) || defined(PORTF)
    }
#endif
#if defined(PORTC) || defined(PORTF)
    else
#endif // defined(PORTC/F)
#endif // defined(PORTB)

    // PORTC OUTPUT ----------------------------------------------------

#if defined(PORTC)
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
        if (port == &PORTC)
    {
#endif // defined(PORTD/B/F)

      hi = PORTC | pinMask;
      lo = PORTC & ~pinMask;
      next = lo;
      if (b & 0x80)
        next = hi;

      // Same as above, just set for PORTC & stripped of comments
      asm volatile(
          "headC:"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "out  %[port] , %[next]"
          "\n\t"
          "mov  %[next] , %[lo]"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[next] , %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "brne headC"
          "\n\t"
          "rjmp doneC"
          "\n\t"
          "bitTimeC:"
          "\n\t"
          "out  %[port], %[next]"
          "\n\t"
          "mov  %[next], %[lo]"
          "\n\t"
          "rol  %[byte]"
          "\n\t"
          "sbrc %[byte], 7"
          "\n\t"
          "mov %[next], %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port], %[lo]"
          "\n\t"
          "ret"
          "\n\t"
          "doneC:"
          "\n"
          : [byte] "+r"(b), [next] "+r"(next), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTC)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTB) || defined(PORTF)
    }
#endif // defined(PORTD/B/F)
#if defined(PORTF)
    else
#endif
#endif // defined(PORTC)

    // PORTF OUTPUT ----------------------------------------------------

#if defined(PORTF)
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
        if (port == &PORTF)
    {
#endif // defined(PORTD/B/C)

      hi = PORTF | pinMask;
      lo = PORTF & ~pinMask;
      next = lo;
      if (b & 0x80)
        next = hi;

      // Same as above, just set for PORTF & stripped of comments
      asm volatile(
          "headF:"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out   %[port], %[hi]"
          "\n\t"
          "rcall bitTimeC"
          "\n\t"
          "out  %[port] , %[hi]"
          "\n\t"
          "rjmp .+0"
          "\n\t"
          "ld   %[byte] , %a[ptr]+"
          "\n\t"
          "out  %[port] , %[next]"
          "\n\t"
          "mov  %[next] , %[lo]"
          "\n\t"
          "sbrc %[byte] , 7"
          "\n\t"
          "mov %[next] , %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port] , %[lo]"
          "\n\t"
          "sbiw %[count], 1"
          "\n\t"
          "brne headF"
          "\n\t"
          "rjmp doneC"
          "\n\t"
          "bitTimeC:"
          "\n\t"
          "out  %[port], %[next]"
          "\n\t"
          "mov  %[next], %[lo]"
          "\n\t"
          "rol  %[byte]"
          "\n\t"
          "sbrc %[byte], 7"
          "\n\t"
          "mov %[next], %[hi]"
          "\n\t"
          "nop"
          "\n\t"
          "out  %[port], %[lo]"
          "\n\t"
          "ret"
          "\n\t"
          "doneC:"
          "\n"
          : [byte] "+r"(b), [next] "+r"(next), [count] "+w"(i)
          : [port] "I"(_SFR_IO_ADDR(PORTF)), [ptr] "e"(ptr), [hi] "r"(hi),
            [lo] "r"(lo));

#if defined(PORTD) || defined(PORTB) || defined(PORTC)
    }
#endif // defined(PORTD/B/C)
#endif // defined(PORTF)

#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz

    // 30 instruction clocks per bit: HHHHHHxxxxxxxxxLLLLLLLLLLLLLLL
    // ST instructions:               ^     ^        ^    (T=0,6,15)

    volatile uint8_t next, bit;

    hi = *port | pinMask;
    lo = *port & ~pinMask;
    next = lo;
    bit = 8;

    asm volatile(
        "head30:"
        "\n\t" // Clk  Pseudocode    (T =  0)
        "st   %a[port], %[hi]"
        "\n\t" // 2    PORT = hi     (T =  2)
        "sbrc %[byte] , 7"
        "\n\t" // 1-2  if(b & 128)
        "mov  %[next], %[hi]"
        "\n\t" // 0-1   next = hi    (T =  4)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T =  6)
        "st   %a[port], %[next]"
        "\n\t" // 2    PORT = next   (T =  8)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 10)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 12)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 14)
        "nop"
        "\n\t" // 1    nop           (T = 15)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 17)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 19)
        "dec  %[bit]"
        "\n\t" // 1    bit--         (T = 20)
        "breq nextbyte30"
        "\n\t" // 1-2  if(bit == 0)
        "rol  %[byte]"
        "\n\t" // 1    b <<= 1       (T = 22)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 24)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 26)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 28)
        "rjmp head30"
        "\n\t" // 2    -> head30 (next bit out)
        "nextbyte30:"
        "\n\t" //                    (T = 22)
        "nop"
        "\n\t" // 1    nop           (T = 23)
        "ldi  %[bit]  , 8"
        "\n\t" // 1    bit = 8       (T = 24)
        "ld   %[byte] , %a[ptr]+"
        "\n\t" // 2    b = *ptr++    (T = 26)
        "sbiw %[count], 1"
        "\n\t" // 2    i--           (T = 28)
        "brne head30"
        "\n" // 1-2  if(i != 0) -> (next byte)
        : [port] "+e"(port),
          [byte] "+r"(b),
          [bit] "+r"(bit),
          [next] "+r"(next),
          [count] "+w"(i)
        : [hi] "r"(hi),
          [lo] "r"(lo),
          [ptr] "e"(ptr));
  }
#endif // NEO_KHZ400

// 16 MHz(ish) AVR --------------------------------------------------------
#elif (F_CPU >= 15400000UL) && (F_CPU <= 19000000L)

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif

    // WS2811 and WS2812 have different hi/lo duty cycles; this is
    // similar but NOT an exact copy of the prior 400-on-8 code.

    // 20 inst. clocks per bit: HHHHHxxxxxxxxLLLLLLL
    // ST instructions:         ^   ^        ^       (T=0,5,13)

    volatile uint8_t next, bit;

    hi = *port | pinMask;
    lo = *port & ~pinMask;
    next = lo;
    bit = 8;

    asm volatile(
        "head20:"
        "\n\t" // Clk  Pseudocode    (T =  0)
        "st   %a[port],  %[hi]"
        "\n\t" // 2    PORT = hi     (T =  2)
        "sbrc %[byte],  7"
        "\n\t" // 1-2  if(b & 128)
        "mov  %[next], %[hi]"
        "\n\t" // 0-1   next = hi    (T =  4)
        "dec  %[bit]"
        "\n\t" // 1    bit--         (T =  5)
        "st   %a[port],  %[next]"
        "\n\t" // 2    PORT = next   (T =  7)
        "mov  %[next] ,  %[lo]"
        "\n\t" // 1    next = lo     (T =  8)
        "breq nextbyte20"
        "\n\t" // 1-2  if(bit == 0) (from dec above)
        "rol  %[byte]"
        "\n\t" // 1    b <<= 1       (T = 10)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 12)
        "nop"
        "\n\t" // 1    nop           (T = 13)
        "st   %a[port],  %[lo]"
        "\n\t" // 2    PORT = lo     (T = 15)
        "nop"
        "\n\t" // 1    nop           (T = 16)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 18)
        "rjmp head20"
        "\n\t" // 2    -> head20 (next bit out)
        "nextbyte20:"
        "\n\t" //                    (T = 10)
        "ldi  %[bit]  ,  8"
        "\n\t" // 1    bit = 8       (T = 11)
        "ld   %[byte] ,  %a[ptr]+"
        "\n\t" // 2    b = *ptr++    (T = 13)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 15)
        "nop"
        "\n\t" // 1    nop           (T = 16)
        "sbiw %[count], 1"
        "\n\t" // 2    i--           (T = 18)
        "brne head20"
        "\n" // 2    if(i != 0) -> (next byte)
        : [port] "+e"(port),
          [byte] "+r"(b),
          [bit] "+r"(bit),
          [next] "+r"(next),
          [count] "+w"(i)
        : [ptr] "e"(ptr),
          [hi] "r"(hi),
          [lo] "r"(lo));

#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz

    // The 400 KHz clock on 16 MHz MCU is the most 'relaxed' version.

    // 40 inst. clocks per bit: HHHHHHHHxxxxxxxxxxxxLLLLLLLLLLLLLLLLLLLL
    // ST instructions:         ^       ^           ^         (T=0,8,20)

    volatile uint8_t next, bit;

    hi = *port | pinMask;
    lo = *port & ~pinMask;
    next = lo;
    bit = 8;

    asm volatile(
        "head40:"
        "\n\t" // Clk  Pseudocode    (T =  0)
        "st   %a[port], %[hi]"
        "\n\t" // 2    PORT = hi     (T =  2)
        "sbrc %[byte] , 7"
        "\n\t" // 1-2  if(b & 128)
        "mov  %[next] , %[hi]"
        "\n\t" // 0-1   next = hi    (T =  4)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T =  6)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T =  8)
        "st   %a[port], %[next]"
        "\n\t" // 2    PORT = next   (T = 10)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 12)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 14)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 16)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 18)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 20)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 22)
        "nop"
        "\n\t" // 1    nop           (T = 23)
        "mov  %[next] , %[lo]"
        "\n\t" // 1    next = lo     (T = 24)
        "dec  %[bit]"
        "\n\t" // 1    bit--         (T = 25)
        "breq nextbyte40"
        "\n\t" // 1-2  if(bit == 0)
        "rol  %[byte]"
        "\n\t" // 1    b <<= 1       (T = 27)
        "nop"
        "\n\t" // 1    nop           (T = 28)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 30)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 32)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 34)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 36)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 38)
        "rjmp head40"
        "\n\t" // 2    -> head40 (next bit out)
        "nextbyte40:"
        "\n\t" //                    (T = 27)
        "ldi  %[bit]  , 8"
        "\n\t" // 1    bit = 8       (T = 28)
        "ld   %[byte] , %a[ptr]+"
        "\n\t" // 2    b = *ptr++    (T = 30)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 32)
        "st   %a[port], %[lo]"
        "\n\t" // 2    PORT = lo     (T = 34)
        "rjmp .+0"
        "\n\t" // 2    nop nop       (T = 36)
        "sbiw %[count], 1"
        "\n\t" // 2    i--           (T = 38)
        "brne head40"
        "\n" // 1-2  if(i != 0) -> (next byte)
        : [port] "+e"(port),
          [byte] "+r"(b),
          [bit] "+r"(bit),
          [next] "+r"(next),
          [count] "+w"(i)
        : [ptr] "e"(ptr),
          [hi] "r"(hi),
          [lo] "r"(lo));
  }
#endif // NEO_KHZ400

#else
#error "CPU SPEED NOT SUPPORTED"
#endif // end F_CPU ifdefs on __AVR__

  // END AVR ----------------------------------------------------------------

#elif defined(__arm__)

    // ARM MCUs -- Teensy 3.0, 3.1, LC, Arduino Due ---------------------------

#if defined(TEENSYDUINO) && defined(KINETISK) // Teensy 3.0, 3.1, 3.2, 3.5, 3.6
#define CYCLES_800_T0H (F_CPU / 4000000)
#define CYCLES_800_T1H (F_CPU / 1250000)
#define CYCLES_800 (F_CPU / 800000)
#define CYCLES_400_T0H (F_CPU / 2000000)
#define CYCLES_400_T1H (F_CPU / 833333)
#define CYCLES_400 (F_CPU / 400000)

  uint8_t *p = pixels,
          *end = p + numBytes, pix, mask;
  volatile uint8_t *set = portSetRegister(pin),
                   *clr = portClearRegister(pin);
  uint32_t cyc;

  ARM_DEMCR |= ARM_DEMCR_TRCENA;
  ARM_DWT_CTRL |= ARM_DWT_CTRL_CYCCNTENA;

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    cyc = ARM_DWT_CYCCNT + CYCLES_800;
    while (p < end)
    {
      pix = *p++;
      for (mask = 0x80; mask; mask >>= 1)
      {
        while (ARM_DWT_CYCCNT - cyc < CYCLES_800)
          ;
        cyc = ARM_DWT_CYCCNT;
        *set = 1;
        if (pix & mask)
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_800_T1H)
            ;
        }
        else
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_800_T0H)
            ;
        }
        *clr = 1;
      }
    }
    while (ARM_DWT_CYCCNT - cyc < CYCLES_800)
      ;
#if defined(NEO_KHZ400)
  }
  else
  { // 400 kHz bitstream
    cyc = ARM_DWT_CYCCNT + CYCLES_400;
    while (p < end)
    {
      pix = *p++;
      for (mask = 0x80; mask; mask >>= 1)
      {
        while (ARM_DWT_CYCCNT - cyc < CYCLES_400)
          ;
        cyc = ARM_DWT_CYCCNT;
        *set = 1;
        if (pix & mask)
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_400_T1H)
            ;
        }
        else
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_400_T0H)
            ;
        }
        *clr = 1;
      }
    }
    while (ARM_DWT_CYCCNT - cyc < CYCLES_400)
      ;
  }
#endif // NEO_KHZ400

#elif defined(TEENSYDUINO) && (defined(__IMXRT1052__) || defined(__IMXRT1062__))
#define CYCLES_800_T0H (F_CPU_ACTUAL / 4000000)
#define CYCLES_800_T1H (F_CPU_ACTUAL / 1250000)
#define CYCLES_800 (F_CPU_ACTUAL / 800000)
#define CYCLES_400_T0H (F_CPU_ACTUAL / 2000000)
#define CYCLES_400_T1H (F_CPU_ACTUAL / 833333)
#define CYCLES_400 (F_CPU_ACTUAL / 400000)

  uint8_t *p = pixels,
          *end = p + numBytes, pix, mask;
  volatile uint32_t *set = portSetRegister(pin),
                    *clr = portClearRegister(pin);
  uint32_t cyc,
      msk = digitalPinToBitMask(pin);

  ARM_DEMCR |= ARM_DEMCR_TRCENA;
  ARM_DWT_CTRL |= ARM_DWT_CTRL_CYCCNTENA;

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    cyc = ARM_DWT_CYCCNT + CYCLES_800;
    while (p < end)
    {
      pix = *p++;
      for (mask = 0x80; mask; mask >>= 1)
      {
        while (ARM_DWT_CYCCNT - cyc < CYCLES_800)
          ;
        cyc = ARM_DWT_CYCCNT;
        *set = msk;
        if (pix & mask)
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_800_T1H)
            ;
        }
        else
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_800_T0H)
            ;
        }
        *clr = msk;
      }
    }
    while (ARM_DWT_CYCCNT - cyc < CYCLES_800)
      ;
#if defined(NEO_KHZ400)
  }
  else
  { // 400 kHz bitstream
    cyc = ARM_DWT_CYCCNT + CYCLES_400;
    while (p < end)
    {
      pix = *p++;
      for (mask = 0x80; mask; mask >>= 1)
      {
        while (ARM_DWT_CYCCNT - cyc < CYCLES_400)
          ;
        cyc = ARM_DWT_CYCCNT;
        *set = msk;
        if (pix & mask)
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_400_T1H)
            ;
        }
        else
        {
          while (ARM_DWT_CYCCNT - cyc < CYCLES_400_T0H)
            ;
        }
        *clr = msk;
      }
    }
    while (ARM_DWT_CYCCNT - cyc < CYCLES_400)
      ;
  }
#endif // NEO_KHZ400

#elif defined(TEENSYDUINO) && defined(__MKL26Z64__) // Teensy-LC

#if F_CPU == 48000000
  uint8_t *p = pixels,
          pix, count, dly,
          bitmask = digitalPinToBitMask(pin);
  volatile uint8_t *reg = portSetRegister(pin);
  uint32_t num = numBytes;
  asm volatile(
      "L%=_begin:"
      "\n\t"
      "ldrb  %[pix], [%[p], #0]"
      "\n\t"
      "lsl   %[pix], #24"
      "\n\t"
      "movs  %[count], #7"
      "\n\t"
      "L%=_loop:"
      "\n\t"
      "lsl   %[pix], #1"
      "\n\t"
      "bcs   L%=_loop_one"
      "\n\t"
      "L%=_loop_zero:"
      "\n\t"
      "strb  %[bitmask], [%[reg], #0]"
      "\n\t"
      "movs  %[dly], #4"
      "\n\t"
      "L%=_loop_delay_T0H:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_loop_delay_T0H"
      "\n\t"
      "strb  %[bitmask], [%[reg], #4]"
      "\n\t"
      "movs  %[dly], #13"
      "\n\t"
      "L%=_loop_delay_T0L:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_loop_delay_T0L"
      "\n\t"
      "b     L%=_next"
      "\n\t"
      "L%=_loop_one:"
      "\n\t"
      "strb  %[bitmask], [%[reg], #0]"
      "\n\t"
      "movs  %[dly], #13"
      "\n\t"
      "L%=_loop_delay_T1H:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_loop_delay_T1H"
      "\n\t"
      "strb  %[bitmask], [%[reg], #4]"
      "\n\t"
      "movs  %[dly], #4"
      "\n\t"
      "L%=_loop_delay_T1L:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_loop_delay_T1L"
      "\n\t"
      "nop"
      "\n\t"
      "L%=_next:"
      "\n\t"
      "sub   %[count], #1"
      "\n\t"
      "bne   L%=_loop"
      "\n\t"
      "lsl   %[pix], #1"
      "\n\t"
      "bcs   L%=_last_one"
      "\n\t"
      "L%=_last_zero:"
      "\n\t"
      "strb  %[bitmask], [%[reg], #0]"
      "\n\t"
      "movs  %[dly], #4"
      "\n\t"
      "L%=_last_delay_T0H:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_last_delay_T0H"
      "\n\t"
      "strb  %[bitmask], [%[reg], #4]"
      "\n\t"
      "movs  %[dly], #10"
      "\n\t"
      "L%=_last_delay_T0L:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_last_delay_T0L"
      "\n\t"
      "b     L%=_repeat"
      "\n\t"
      "L%=_last_one:"
      "\n\t"
      "strb  %[bitmask], [%[reg], #0]"
      "\n\t"
      "movs  %[dly], #13"
      "\n\t"
      "L%=_last_delay_T1H:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_last_delay_T1H"
      "\n\t"
      "strb  %[bitmask], [%[reg], #4]"
      "\n\t"
      "movs  %[dly], #1"
      "\n\t"
      "L%=_last_delay_T1L:"
      "\n\t"
      "sub   %[dly], #1"
      "\n\t"
      "bne   L%=_last_delay_T1L"
      "\n\t"
      "nop"
      "\n\t"
      "L%=_repeat:"
      "\n\t"
      "add   %[p], #1"
      "\n\t"
      "sub   %[num], #1"
      "\n\t"
      "bne   L%=_begin"
      "\n\t"
      "L%=_done:"
      "\n\t"
      : [p] "+r"(p),
        [pix] "=&r"(pix),
        [count] "=&r"(count),
        [dly] "=&r"(dly),
        [num] "+r"(num)
      : [bitmask] "r"(bitmask),
        [reg] "r"(reg));
#else
#error "Sorry, only 48 MHz is supported, please set Tools > CPU Speed to 48 MHz"
#endif // F_CPU == 48000000

  // Begin of support for nRF52 based boards  -------------------------

#elif defined(NRF52) || defined(NRF52_SERIES)
// [[[Begin of the Neopixel NRF52 EasyDMA implementation
//                                    by the Hackerspace San Salvador]]]
// This technique uses the PWM peripheral on the NRF52. The PWM uses the
// EasyDMA feature included on the chip. This technique loads the duty
// cycle configuration for each cycle when the PWM is enabled. For this
// to work we need to store a 16 bit configuration for each bit of the
// RGB(W) values in the pixel buffer.
// Comparator values for the PWM were hand picked and are guaranteed to
// be 100% organic to preserve freshness and high accuracy. Current
// parameters are:
//   * PWM Clock: 16Mhz
//   * Minimum step time: 62.5ns
//   * Time for zero in high (T0H): 0.31ms
//   * Time for one in high (T1H): 0.75ms
//   * Cycle time:  1.25us
//   * Frequency: 800Khz
// For 400Khz we just double the calculated times.
// ---------- BEGIN Constants for the EasyDMA implementation -----------
// The PWM starts the duty cycle in LOW. To start with HIGH we
// need to set the 15th bit on each register.

// WS2812 (rev A) timing is 0.35 and 0.7us
//#define MAGIC_T0H               5UL | (0x8000) // 0.3125us
//#define MAGIC_T1H              12UL | (0x8000) // 0.75us

// WS2812B (rev B) timing is 0.4 and 0.8 us
#define MAGIC_T0H 6UL | (0x8000)         // 0.375us
#define MAGIC_T1H 13UL | (0x8000)        // 0.8125us

// WS2811 (400 khz) timing is 0.5 and 1.2
#define MAGIC_T0H_400KHz 8UL | (0x8000)  // 0.5us
#define MAGIC_T1H_400KHz 19UL | (0x8000) // 1.1875us

// For 400Khz, we double value of CTOPVAL
#define CTOPVAL 20UL                     // 1.25us
#define CTOPVAL_400KHz 40UL              // 2.5us

// ---------- END Constants for the EasyDMA implementation -------------
//
// If there is no device available an alternative cycle-counter
// implementation is tried.
// The nRF52 runs with a fixed clock of 64Mhz. The alternative
// implementation is the same as the one used for the Teensy 3.0/1/2 but
// with the Nordic SDK HAL & registers syntax.
// The number of cycles was hand picked and is guaranteed to be 100%
// organic to preserve freshness and high accuracy.
// ---------- BEGIN Constants for cycle counter implementation ---------
#define CYCLES_800_T0H 18                // ~0.36 uS
#define CYCLES_800_T1H 41                // ~0.76 uS
#define CYCLES_800 71                    // ~1.25 uS

#define CYCLES_400_T0H 26 // ~0.50 uS
#define CYCLES_400_T1H 70 // ~1.26 uS
#define CYCLES_400 156    // ~2.50 uS
  // ---------- END of Constants for cycle counter implementation --------

  // To support both the SoftDevice + Neopixels we use the EasyDMA
  // feature from the NRF25. However this technique implies to
  // generate a pattern and store it on the memory. The actual
  // memory used in bytes corresponds to the following formula:
  //              totalMem = numBytes*8*2+(2*2)
  // The two additional bytes at the end are needed to reset the
  // sequence.
  //
  // If there is not enough memory, we will fall back to cycle counter
  // using DWT
  uint32_t pattern_size = numBytes * 8 * sizeof(uint16_t) + 2 * sizeof(uint16_t);
  uint16_t *pixels_pattern = NULL;

  NRF_PWM_Type *pwm = NULL;

  // Try to find a free PWM device, which is not enabled
  // and has no connected pins
  NRF_PWM_Type *PWM[] = {
    NRF_PWM0,
    NRF_PWM1,
    NRF_PWM2
#if defined(NRF_PWM3)
    ,
    NRF_PWM3
#endif
  };

  for (unsigned int device = 0; device < (sizeof(PWM) / sizeof(PWM[0])); device++)
  {
    if ((PWM[device]->ENABLE == 0) &&
        (PWM[device]->PSEL.OUT[0] & PWM_PSEL_OUT_CONNECT_Msk) &&
        (PWM[device]->PSEL.OUT[1] & PWM_PSEL_OUT_CONNECT_Msk) &&
        (PWM[device]->PSEL.OUT[2] & PWM_PSEL_OUT_CONNECT_Msk) &&
        (PWM[device]->PSEL.OUT[3] & PWM_PSEL_OUT_CONNECT_Msk))
    {
      pwm = PWM[device];
      break;
    }
  }

  // only malloc if there is PWM device available
  if (pwm != NULL)
  {
#if defined(ARDUINO_NRF52_ADAFRUIT) // use thread-safe malloc
    pixels_pattern = (uint16_t *)rtos_malloc(pattern_size);
#else
    pixels_pattern = (uint16_t *)malloc(pattern_size);
#endif
  }

  // Use the identified device to choose the implementation
  // If a PWM device is available use DMA
  if ((pixels_pattern != NULL) && (pwm != NULL))
  {
    uint16_t pos = 0; // bit position

    for (uint16_t n = 0; n < numBytes; n++)
    {
      uint8_t pix = pixels[n];

      for (uint8_t mask = 0x80; mask > 0; mask >>= 1)
      {
#if defined(NEO_KHZ400)
        if (!is800KHz)
        {
          pixels_pattern[pos] = (pix & mask) ? MAGIC_T1H_400KHz : MAGIC_T0H_400KHz;
        }
        else
#endif
        {
          pixels_pattern[pos] = (pix & mask) ? MAGIC_T1H : MAGIC_T0H;
        }

        pos++;
      }
    }

    // Zero padding to indicate the end of que sequence
    pixels_pattern[pos++] = 0 | (0x8000); // Seq end
    pixels_pattern[pos++] = 0 | (0x8000); // Seq end

    // Set the wave mode to count UP
    pwm->MODE = (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);

    // Set the PWM to use the 16MHz clock
    pwm->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 << PWM_PRESCALER_PRESCALER_Pos);

    // Setting of the maximum count
    // but keeping it on 16Mhz allows for more granularity just
    // in case someone wants to do more fine-tuning of the timing.
#if defined(NEO_KHZ400)
    if (!is800KHz)
    {
      pwm->COUNTERTOP = (CTOPVAL_400KHz << PWM_COUNTERTOP_COUNTERTOP_Pos);
    }
    else
#endif
    {
      pwm->COUNTERTOP = (CTOPVAL << PWM_COUNTERTOP_COUNTERTOP_Pos);
    }

    // Disable loops, we want the sequence to repeat only once
    pwm->LOOP = (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);

    // On the "Common" setting the PWM uses the same pattern for the
    // for supported sequences. The pattern is stored on half-word
    // of 16bits
    pwm->DECODER = (PWM_DECODER_LOAD_Common << PWM_DECODER_LOAD_Pos) |
                   (PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);

    // Pointer to the memory storing the patter
    pwm->SEQ[0].PTR = (uint32_t)(pixels_pattern) << PWM_SEQ_PTR_PTR_Pos;

    // Calculation of the number of steps loaded from memory.
    pwm->SEQ[0].CNT = (pattern_size / sizeof(uint16_t)) << PWM_SEQ_CNT_CNT_Pos;

    // The following settings are ignored with the current config.
    pwm->SEQ[0].REFRESH = 0;
    pwm->SEQ[0].ENDDELAY = 0;

    // The Neopixel implementation is a blocking algorithm. DMA
    // allows for non-blocking operation. To "simulate" a blocking
    // operation we enable the interruption for the end of sequence
    // and block the execution thread until the event flag is set by
    // the peripheral.
    //    pwm->INTEN |= (PWM_INTEN_SEQEND0_Enabled<<PWM_INTEN_SEQEND0_Pos);

// PSEL must be configured before enabling PWM
#if defined(ARDUINO_ARCH_NRF52840)
    pwm->PSEL.OUT[0] = g_APinDescription[pin].name;
#else
    pwm->PSEL.OUT[0] = g_ADigitalPinMap[pin];
#endif

    // Enable the PWM
    pwm->ENABLE = 1;

    // After all of this and many hours of reading the documentation
    // we are ready to start the sequence...
    pwm->EVENTS_SEQEND[0] = 0;
    pwm->TASKS_SEQSTART[0] = 1;

    // But we have to wait for the flag to be set.
    while (!pwm->EVENTS_SEQEND[0])
    {
#if defined(ARDUINO_NRF52_ADAFRUIT) || defined(ARDUINO_ARCH_NRF52840)
      yield();
#endif
    }

    // Before leave we clear the flag for the event.
    pwm->EVENTS_SEQEND[0] = 0;

    // We need to disable the device and disconnect
    // all the outputs before leave or the device will not
    // be selected on the next call.
    // TODO: Check if disabling the device causes performance issues.
    pwm->ENABLE = 0;

    pwm->PSEL.OUT[0] = 0xFFFFFFFFUL;

#if defined(ARDUINO_NRF52_ADAFRUIT) // use thread-safe free
    rtos_free(pixels_pattern);
#else
    free(pixels_pattern);
#endif
  } // End of DMA implementation
  // ---------------------------------------------------------------------
  else
  {
#ifndef ARDUINO_ARCH_NRF52840
// Fall back to DWT
#if defined(ARDUINO_NRF52_ADAFRUIT)
    // Bluefruit Feather 52 uses freeRTOS
    // Critical Section is used since it does not block SoftDevice execution
    taskENTER_CRITICAL();
#elif defined(NRF52_DISABLE_INT)
    // If you are using the Bluetooth SoftDevice we advise you to not disable
    // the interrupts. Disabling the interrupts even for short periods of time
    // causes the SoftDevice to stop working.
    // Disable the interrupts only in cases where you need high performance for
    // the LEDs and if you are not using the EasyDMA feature.
    __disable_irq();
#endif

    NRF_GPIO_Type *nrf_port = (NRF_GPIO_Type *)digitalPinToPort(pin);
    uint32_t pinMask = digitalPinToBitMask(pin);

    uint32_t CYCLES_X00 = CYCLES_800;
    uint32_t CYCLES_X00_T1H = CYCLES_800_T1H;
    uint32_t CYCLES_X00_T0H = CYCLES_800_T0H;

#if defined(NEO_KHZ400)
    if (!is800KHz)
    {
      CYCLES_X00 = CYCLES_400;
      CYCLES_X00_T1H = CYCLES_400_T1H;
      CYCLES_X00_T0H = CYCLES_400_T0H;
    }
#endif

    // Enable DWT in debug core
    CoreDebug->DEMCR |= CoreDebug_DEMCR_TRCENA_Msk;
    DWT->CTRL |= DWT_CTRL_CYCCNTENA_Msk;

    // Tries to re-send the frame if is interrupted by the SoftDevice.
    while (1)
    {
      uint8_t *p = pixels;

      uint32_t cycStart = DWT->CYCCNT;
      uint32_t cyc = 0;

      for (uint16_t n = 0; n < numBytes; n++)
      {
        uint8_t pix = *p++;

        for (uint8_t mask = 0x80; mask; mask >>= 1)
        {
          while (DWT->CYCCNT - cyc < CYCLES_X00)
            ;
          cyc = DWT->CYCCNT;

          nrf_port->OUTSET |= pinMask;

          if (pix & mask)
          {
            while (DWT->CYCCNT - cyc < CYCLES_X00_T1H)
              ;
          }
          else
          {
            while (DWT->CYCCNT - cyc < CYCLES_X00_T0H)
              ;
          }

          nrf_port->OUTCLR |= pinMask;
        }
      }
      while (DWT->CYCCNT - cyc < CYCLES_X00)
        ;

      // If total time longer than 25%, resend the whole data.
      // Since we are likely to be interrupted by SoftDevice
      if ((DWT->CYCCNT - cycStart) < (8 * numBytes * ((CYCLES_X00 * 5) / 4)))
      {
        break;
      }

      // re-send need 300us delay
      delayMicroseconds(300);
    }

// Enable interrupts again
#if defined(ARDUINO_NRF52_ADAFRUIT)
    taskEXIT_CRITICAL();
#elif defined(NRF52_DISABLE_INT)
    __enable_irq();
#endif
#endif
  }
  // END of NRF52 implementation

#elif defined(__SAMD21E17A__) || defined(__SAMD21G18A__) || defined(__SAMD21E18A__) || defined(__SAMD21J18A__) // Arduino Zero, Gemma/Trinket M0, SODAQ Autonomo and others
  // Tried this with a timer/counter, couldn't quite get adequate
  // resolution. So yay, you get a load of goofball NOPs...

  uint8_t *ptr, *end, p, bitMask, portNum;
  uint32_t pinMask;

  portNum = g_APinDescription[pin].ulPort;
  pinMask = 1ul << g_APinDescription[pin].ulPin;
  ptr = pixels;
  end = ptr + numBytes;
  p = *ptr++;
  bitMask = 0x80;

  volatile uint32_t *set = &(PORT->Group[portNum].OUTSET.reg),
                    *clr = &(PORT->Group[portNum].OUTCLR.reg);

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    for (;;)
    {
      *set = pinMask;
      asm("nop; nop; nop; nop; nop; nop; nop; nop;");
      if (p & bitMask)
      {
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop;");
        *clr = pinMask;
      }
      else
      {
        *clr = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop;");
      }
      if (bitMask >>= 1)
      {
        asm("nop; nop; nop; nop; nop; nop; nop; nop; nop;");
      }
      else
      {
        if (ptr >= end)
          break;
        p = *ptr++;
        bitMask = 0x80;
      }
    }
#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz bitstream
    for (;;)
    {
      *set = pinMask;
      asm("nop; nop; nop; nop; nop; nop; nop; nop; nop; nop; nop;");
      if (p & bitMask)
      {
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop;");
        *clr = pinMask;
      }
      else
      {
        *clr = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop;");
      }
      asm("nop; nop; nop; nop; nop; nop; nop; nop;"
          "nop; nop; nop; nop; nop; nop; nop; nop;"
          "nop; nop; nop; nop; nop; nop; nop; nop;"
          "nop; nop; nop; nop; nop; nop; nop; nop;");
      if (bitMask >>= 1)
      {
        asm("nop; nop; nop; nop; nop; nop; nop;");
      }
      else
      {
        if (ptr >= end)
          break;
        p = *ptr++;
        bitMask = 0x80;
      }
    }
  }
#endif

#elif defined(__SAMD51__) // M4

  uint8_t *ptr, *end, p, bitMask, portNum, bit;
  uint32_t pinMask;

  portNum = g_APinDescription[pin].ulPort;
  pinMask = 1ul << g_APinDescription[pin].ulPin;
  ptr = pixels;
  end = ptr + numBytes;
  p = *ptr++;
  bitMask = 0x80;

  volatile uint32_t *set = &(PORT->Group[portNum].OUTSET.reg),
                    *clr = &(PORT->Group[portNum].OUTCLR.reg);

  // SAMD51 overclock-compatible timing is only a mild abomination.
  // It uses SysTick for a consistent clock reference regardless of
  // optimization / cache settings.  That's the good news.  The bad news,
  // since SysTick->VAL is a volatile type it's slow to access...and then,
  // with the SysTick interval that Arduino sets up (1 ms), this would
  // require a subtract and MOD operation for gauging elapsed time, and
  // all taken in combination that lacks adequate temporal resolution
  // for NeoPixel timing.  So a kind of horrible thing is done here...
  // since interrupts are turned off anyway and it's generally accepted
  // by now that we're gonna lose track of time in the NeoPixel lib,
  // the SysTick timer is reconfigured for a period matching the NeoPixel
  // bit timing (either 800 or 400 KHz) and we watch SysTick->VAL very
  // closely (just a threshold, no subtract or MOD or anything) and that
  // seems to work just well enough.  When finished, the SysTick
  // peripheral is set back to its original state.

  uint32_t t0, t1, top, ticks,
      saveLoad = SysTick->LOAD, saveVal = SysTick->VAL;

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    top = (uint32_t)(F_CPU * 0.00000125);      // Bit hi + lo = 1.25 uS
    t0 = top - (uint32_t)(F_CPU * 0.00000040); // 0 = 0.4 uS hi
    t1 = top - (uint32_t)(F_CPU * 0.00000080); // 1 = 0.8 uS hi
#if defined(NEO_KHZ400)
  }
  else
  {                                            // 400 KHz bitstream
    top = (uint32_t)(F_CPU * 0.00000250);      // Bit hi + lo = 2.5 uS
    t0 = top - (uint32_t)(F_CPU * 0.00000050); // 0 = 0.5 uS hi
    t1 = top - (uint32_t)(F_CPU * 0.00000120); // 1 = 1.2 uS hi
  }
#endif

  SysTick->LOAD = top; // Config SysTick for NeoPixel bit freq
  SysTick->VAL = top;  // Set to start value (counts down)
  (void)SysTick->VAL;  // Dummy read helps sync up 1st bit

  for (;;)
  {
    *set = pinMask;                  // Set output high
    ticks = (p & bitMask) ? t1 : t0; // SysTick threshold,
    while (SysTick->VAL > ticks)
      ;             // wait for it
    *clr = pinMask; // Set output low
    if (!(bitMask >>= 1))
    { // Next bit for this byte...done?
      if (ptr >= end)
        break;        // If last byte sent, exit loop
      p = *ptr++;     // Fetch next byte
      bitMask = 0x80; // Reset bitmask
    }
    while (SysTick->VAL <= ticks)
      ; // Wait for rollover to 'top'
  }

  SysTick->LOAD = saveLoad; // Restore SysTick rollover to 1 ms
  SysTick->VAL = saveVal;   // Restore SysTick value

#elif defined(ARDUINO_STM32_FEATHER) // FEATHER WICED (120MHz)

  // Tried this with a timer/counter, couldn't quite get adequate
  // resolution. So yay, you get a load of goofball NOPs...

  uint8_t *ptr, *end, p, bitMask;
  uint32_t pinMask;

  pinMask = BIT(PIN_MAP[pin].gpio_bit);
  ptr = pixels;
  end = ptr + numBytes;
  p = *ptr++;
  bitMask = 0x80;

  volatile uint16_t *set = &(PIN_MAP[pin].gpio_device->regs->BSRRL);
  volatile uint16_t *clr = &(PIN_MAP[pin].gpio_device->regs->BSRRH);

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    for (;;)
    {
      if (p & bitMask)
      { // ONE
        // High 800ns
        *set = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop;");
        // Low 450ns
        *clr = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop;");
      }
      else
      { // ZERO
        // High 400ns
        *set = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop;");
        // Low 850ns
        *clr = pinMask;
        asm("nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop; nop; nop; nop; nop;"
            "nop; nop; nop; nop;");
      }
      if (bitMask >>= 1)
      {
        // Move on to the next pixel
        asm("nop;");
      }
      else
      {
        if (ptr >= end)
          break;
        p = *ptr++;
        bitMask = 0x80;
      }
    }
#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz bitstream
    // ToDo!
  }
#endif

#elif defined(TARGET_LPC1768)
  uint8_t *ptr, *end, p, bitMask;
  ptr = pixels;
  end = ptr + numBytes;
  p = *ptr++;
  bitMask = 0x80;

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    for (;;)
    {
      if (p & bitMask)
      {
        // data ONE high
        // min: 550 typ: 700 max: 5,500
        gpio_set(pin);
        time::delay_ns(550);
        // min: 450 typ: 600 max: 5,000
        gpio_clear(pin);
        time::delay_ns(450);
      }
      else
      {
        // data ZERO high
        // min: 200  typ: 350 max: 500
        gpio_set(pin);
        time::delay_ns(200);
        // data low
        // min: 450 typ: 600 max: 5,000
        gpio_clear(pin);
        time::delay_ns(450);
      }
      if (bitMask >>= 1)
      {
        // Move on to the next pixel
        asm("nop;");
      }
      else
      {
        if (ptr >= end)
          break;
        p = *ptr++;
        bitMask = 0x80;
      }
    }
#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz bitstream
    // ToDo!
  }
#endif
#elif defined(ARDUINO_ARCH_STM32) || defined(ARDUINO_ARCH_ARDUINO_CORE_STM32)
  uint8_t *p = pixels, *end = p + numBytes,
          pix = *p++, mask = 0x80;
  uint32_t cyc;
  uint32_t saveLoad = SysTick->LOAD, saveVal = SysTick->VAL;
#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    uint32_t top = (F_CPU / 800000);       // 1.25µs
    uint32_t t0 = top - (F_CPU / 2500000); // 0.4µs
    uint32_t t1 = top - (F_CPU / 1250000); // 0.8µs
    SysTick->LOAD = top - 1;               // Config SysTick for NeoPixel bit freq
    SysTick->VAL = 0;                      // Set to start value
    for (;;)
    {
      LL_GPIO_SetOutputPin(gpioPort, gpioPin);
      cyc = (pix & mask) ? t1 : t0;
      while (SysTick->VAL > cyc)
        ;
      LL_GPIO_ResetOutputPin(gpioPort, gpioPin);
      if (!(mask >>= 1))
      {
        if (p >= end)
          break;
        pix = *p++;
        mask = 0x80;
      }
      while (SysTick->VAL <= cyc)
        ;
    }
#if defined(NEO_KHZ400)
  }
  else
  {                                        // 400 kHz bitstream
    uint32_t top = (F_CPU / 400000);       // 2.5µs
    uint32_t t0 = top - (F_CPU / 2000000); // 0.5µs
    uint32_t t1 = top - (F_CPU / 833333);  // 1.2µs
    SysTick->LOAD = top - 1;               // Config SysTick for NeoPixel bit freq
    SysTick->VAL = 0;                      // Set to start value
    for (;;)
    {
      LL_GPIO_SetOutputPin(gpioPort, gpioPin);
      cyc = (pix & mask) ? t1 : t0;
      while (SysTick->VAL > cyc)
        ;
      LL_GPIO_ResetOutputPin(gpioPort, gpioPin);
      if (!(mask >>= 1))
      {
        if (p >= end)
          break;
        pix = *p++;
        mask = 0x80;
      }
      while (SysTick->VAL <= cyc)
        ;
    }
  }
#endif // NEO_KHZ400
  SysTick->LOAD = saveLoad; // Restore SysTick rollover to 1 ms
  SysTick->VAL = saveVal;   // Restore SysTick value
#elif defined(NRF51)
  uint8_t *p = pixels,
          pix, count, mask;
  int32_t num = numBytes;
  unsigned int bitmask = (1 << g_ADigitalPinMap[pin]);
  // https://github.com/sandeepmistry/arduino-nRF5/blob/dc53980c8bac27898fca90d8ecb268e11111edc1/variants/BBCmicrobit/variant.cpp

  volatile unsigned int *reg = (unsigned int *)(0x50000000UL + 0x508);

  // https://github.com/sandeepmistry/arduino-nRF5/blob/dc53980c8bac27898fca90d8ecb268e11111edc1/cores/nRF5/SDK/components/device/nrf51.h
  // http://www.iot-programmer.com/index.php/books/27-micro-bit-iot-in-c/chapters-micro-bit-iot-in-c/47-micro-bit-iot-in-c-fast-memory-mapped-gpio?showall=1
  // https://github.com/Microsoft/pxt-neopixel/blob/master/sendbuffer.asm

  asm volatile(
      // "cpsid i" ; disable irq

      //    b .start
      "b  L%=_start"
      "\n\t"
      // .nextbit:               ;            C0
      "L%=_nextbit:"
      "\n\t" //;            C0
      //    str r1, [r3, #0]    ; pin := hi  C2
      "strb %[bitmask], [%[reg], #0]"
      "\n\t" //; pin := hi  C2
      //    tst r6, r0          ;            C3
      "tst %[mask], %[pix]"
      "\n\t" //          ;            C3
      //    bne .islate         ;            C4
      "bne L%=_islate"
      "\n\t" //;            C4
      //    str r1, [r2, #0]    ; pin := lo  C6
      "strb %[bitmask], [%[reg], #4]"
      "\n\t" //; pin := lo  C6
      // .islate:
      "L%=_islate:"
      "\n\t"
      //    lsrs r6, r6, #1     ; r6 >>= 1   C7
      "lsr %[mask], %[mask], #1"
      "\n\t" //; r6 >>= 1   C7
      //    bne .justbit        ;            C8
      "bne L%=_justbit"
      "\n\t" //;            C8

      //    ; not just a bit - need new byte
      //    adds r4, #1         ; r4++       C9
      "add %[p], #1"
      "\n\t" //; r4++       C9
      //    subs r5, #1         ; r5--       C10
      "sub %[num], #1"
      "\n\t" //; r5--       C10
      //    bcc .stop           ; if (r5<0) goto .stop  C11
      "bcc L%=_stop"
      "\n\t" //; if (r5<0) goto .stop  C11
      // .start:
      "L%=_start:"
      //    movs r6, #0x80      ; reset mask C12
      "movs %[mask], #0x80"
      "\n\t" //; reset mask C12
      //    nop                 ;            C13
      "nop"
      "\n\t" //;            C13

      // .common:               ;             C13
      "L%=_common:"
      "\n\t" //;            C13
      //    str r1, [r2, #0]   ; pin := lo   C15
      "strb %[bitmask], [%[reg], #4]"
      "\n\t" //; pin := lo  C15
      //    ; always re-load byte - it just fits with the cycles better this way
      //    ldrb r0, [r4, #0]  ; r0 := *r4   C17
      "ldrb  %[pix], [%[p], #0]"
      "\n\t" //; r0 := *r4   C17
      //    b .nextbit         ;             C20
      "b L%=_nextbit"
      "\n\t" //;             C20

      // .justbit: ; C10
      "L%=_justbit:"
      "\n\t" //; C10
      //    ; no nops, branch taken is already 3 cycles
      //    b .common ; C13
      "b L%=_common"
      "\n\t" //; C13

      // .stop:
      "L%=_stop:"
      "\n\t"
      //    str r1, [r2, #0]   ; pin := lo
      "strb %[bitmask], [%[reg], #4]"
      "\n\t" //; pin := lo
      //    cpsie i            ; enable irq

      : [p] "+r"(p),
        [pix] "=&r"(pix),
        [count] "=&r"(count),
        [mask] "=&r"(mask),
        [num] "+r"(num)
      : [bitmask] "r"(bitmask),
        [reg] "r"(reg));

#elif defined(__SAM3X8E__) // Arduino Due

#define SCALE VARIANT_MCK / 2UL / 1000000UL
#define INST (2UL * F_CPU / VARIANT_MCK)
#define TIME_800_0 ((int)(0.40 * SCALE + 0.5) - (5 * INST))
#define TIME_800_1 ((int)(0.80 * SCALE + 0.5) - (5 * INST))
#define PERIOD_800 ((int)(1.25 * SCALE + 0.5) - (5 * INST))
#define TIME_400_0 ((int)(0.50 * SCALE + 0.5) - (5 * INST))
#define TIME_400_1 ((int)(1.20 * SCALE + 0.5) - (5 * INST))
#define PERIOD_400 ((int)(2.50 * SCALE + 0.5) - (5 * INST))

  int pinMask, time0, time1, period, t;
  Pio *port;
  volatile WoReg *portSet, *portClear, *timeValue, *timeReset;
  uint8_t *p, *end, pix, mask;

  pmc_set_writeprotect(false);
  pmc_enable_periph_clk((uint32_t)TC3_IRQn);
  TC_Configure(TC1, 0,
               TC_CMR_WAVE | TC_CMR_WAVSEL_UP | TC_CMR_TCCLKS_TIMER_CLOCK1);
  TC_Start(TC1, 0);

  pinMask = g_APinDescription[pin].ulPin;  // Don't 'optimize' these into
  port = g_APinDescription[pin].pPort;     // declarations above. Want to
  portSet = &(port->PIO_SODR);             // burn a few cycles after
  portClear = &(port->PIO_CODR);           // starting timer to minimize
  timeValue = &(TC1->TC_CHANNEL[0].TC_CV); // the initial 'while'.
  timeReset = &(TC1->TC_CHANNEL[0].TC_CCR);
  p = pixels;
  end = p + numBytes;
  pix = *p++;
  mask = 0x80;

#if defined(NEO_KHZ400) // 800 KHz check needed only if 400 KHz support enabled
  if (is800KHz)
  {
#endif
    time0 = TIME_800_0;
    time1 = TIME_800_1;
    period = PERIOD_800;
#if defined(NEO_KHZ400)
  }
  else
  { // 400 KHz bitstream
    time0 = TIME_400_0;
    time1 = TIME_400_1;
    period = PERIOD_400;
  }
#endif

  for (t = time0;; t = time0)
  {
    if (pix & mask)
      t = time1;
    while (*timeValue < (unsigned)period)
      ;
    *portSet = pinMask;
    *timeReset = TC_CCR_CLKEN | TC_CCR_SWTRG;
    while (*timeValue < (unsigned)t)
      ;
    *portClear = pinMask;
    if (!(mask >>= 1))
    { // This 'inside-out' loop logic utilizes
      if (p >= end)
        break; // idle time to minimize inter-byte delays.
      pix = *p++;
      mask = 0x80;
    }
  }
  while (*timeValue < (unsigned)period)
    ; // Wait for last bit
  TC_Stop(TC1, 0);

#endif // end Due

  // END ARM ----------------------------------------------------------------

#elif defined(ESP8266) || defined(ESP32)

  // ESP8266 ----------------------------------------------------------------

  // ESP8266 show() is external to enforce ICACHE_RAM_ATTR execution
  espShow(pin, pixels, numBytes, is800KHz);

#elif defined(__ARDUINO_ARC__)

    // Arduino 101  -----------------------------------------------------------

#define NOPx7            \
  {                      \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
    __builtin_arc_nop(); \
  }

  PinDescription *pindesc = &g_APinDescription[pin];
  register uint32_t loop = 8 * numBytes; // one loop to handle all bytes and all bits
  register uint8_t *p = pixels;
  register uint32_t currByte = (uint32_t)(*p);
  register uint32_t currBit = 0x80 & currByte;
  register uint32_t bitCounter = 0;
  register uint32_t first = 1;

  // The loop is unusual. Very first iteration puts all the way LOW to the wire -
  // constant LOW does not affect NEOPIXEL, so there is no visible effect displayed.
  // During that very first iteration CPU caches instructions in the loop.
  // Because of the caching process, "CPU slows down". NEOPIXEL pulse is very time sensitive
  // that's why we let the CPU cache first and we start regular pulse from 2nd iteration
  if (pindesc->ulGPIOType == SS_GPIO)
  {
    register uint32_t reg = pindesc->ulGPIOBase + SS_GPIO_SWPORTA_DR;
    uint32_t reg_val = __builtin_arc_lr((volatile uint32_t)reg);
    register uint32_t reg_bit_high = reg_val | (1 << pindesc->ulGPIOId);
    register uint32_t reg_bit_low = reg_val & ~(1 << pindesc->ulGPIOId);

    loop += 1; // include first, special iteration
    while (loop--)
    {
      if (!first)
      {
        currByte <<= 1;
        bitCounter++;
      }

      // 1 is >550ns high and >450ns low; 0 is 200..500ns high and >450ns low
      __builtin_arc_sr(first ? reg_bit_low : reg_bit_high, (volatile uint32_t)reg);
      if (currBit)
      { // ~400ns HIGH (740ns overall)
        NOPx7
            NOPx7
      }
      // ~340ns HIGH
      NOPx7
      __builtin_arc_nop();

      // 820ns LOW; per spec, max allowed low here is 5000ns */
      __builtin_arc_sr(reg_bit_low, (volatile uint32_t)reg);
      NOPx7
          NOPx7

          if (bitCounter >= 8)
      {
        bitCounter = 0;
        currByte = (uint32_t)(*++p);
      }

      currBit = 0x80 & currByte;
      first = 0;
    }
  }
  else if (pindesc->ulGPIOType == SOC_GPIO)
  {
    register uint32_t reg = pindesc->ulGPIOBase + SOC_GPIO_SWPORTA_DR;
    uint32_t reg_val = MMIO_REG_VAL(reg);
    register uint32_t reg_bit_high = reg_val | (1 << pindesc->ulGPIOId);
    register uint32_t reg_bit_low = reg_val & ~(1 << pindesc->ulGPIOId);

    loop += 1; // include first, special iteration
    while (loop--)
    {
      if (!first)
      {
        currByte <<= 1;
        bitCounter++;
      }
      MMIO_REG_VAL(reg) = first ? reg_bit_low : reg_bit_high;
      if (currBit)
      { // ~430ns HIGH (740ns overall)
        NOPx7
            NOPx7
            __builtin_arc_nop();
      }
      // ~310ns HIGH
      NOPx7

          // 850ns LOW; per spec, max allowed low here is 5000ns */
          MMIO_REG_VAL(reg) = reg_bit_low;
      NOPx7
          NOPx7

          if (bitCounter >= 8)
      {
        bitCounter = 0;
        currByte = (uint32_t)(*++p);
      }

      currBit = 0x80 & currByte;
      first = 0;
    }
  }

#else
#error Architecture not supported
#endif

  // END ARCHITECTURE SELECT ------------------------------------------------

#if !(defined(NRF52) || defined(NRF52_SERIES))
  interrupts();
#endif

  endTime = micros(); // Save EOD time for latch on next call
}

/*!
  @brief   Set/change the NeoPixel output pin number. Previous pin,
           if any, is set to INPUT and the new pin is set to OUTPUT.
  @param   p  Arduino pin number (-1 = no pin).
*/
void Adafruit_NeoPixel::setPin(uint16_t p)
{
  if (begun && (pin >= 0))
    pinMode(pin, INPUT);
  pin = p;
  if (begun)
  {
    pinMode(p, OUTPUT);
    digitalWrite(p, LOW);
  }
#if defined(__AVR__)
  port = portOutputRegister(digitalPinToPort(p));
  pinMask = digitalPinToBitMask(p);
#endif
#if defined(ARDUINO_ARCH_STM32) || defined(ARDUINO_ARCH_ARDUINO_CORE_STM32)
  gpioPort = digitalPinToPort(p);
  gpioPin = STM_LL_GPIO_PIN(digitalPinToPinName(p));
#endif
}

/*!
  @brief   Set a pixel's color using separate red, green and blue
           components. If using RGBW pixels, white will be set to 0.
  @param   n  Pixel index, starting from 0.
  @param   r  Red brightness, 0 = minimum (off), 255 = maximum.
  @param   g  Green brightness, 0 = minimum (off), 255 = maximum.
  @param   b  Blue brightness, 0 = minimum (off), 255 = maximum.
*/
void Adafruit_NeoPixel::setPixelColor(
    uint16_t n, uint8_t r, uint8_t g, uint8_t b)
{

  if (n < numLEDs)
  {
    if (brightness)
    { // See notes in setBrightness()
      r = (r * brightness) >> 8;
      g = (g * brightness) >> 8;
      b = (b * brightness) >> 8;
    }
    uint8_t *p;
    if (wOffset == rOffset)
    {                     // Is an RGB-type strip
      p = &pixels[n * 3]; // 3 bytes per pixel
    }
    else
    {                     // Is a WRGB-type strip
      p = &pixels[n * 4]; // 4 bytes per pixel
      p[wOffset] = 0;     // But only R,G,B passed -- set W to 0
    }
    p[rOffset] = r; // R,G,B always stored
    p[gOffset] = g;
    p[bOffset] = b;
  }
}

/*!
  @brief   Set a pixel's color using separate red, green, blue and white
           components (for RGBW NeoPixels only).
  @param   n  Pixel index, starting from 0.
  @param   r  Red brightness, 0 = minimum (off), 255 = maximum.
  @param   g  Green brightness, 0 = minimum (off), 255 = maximum.
  @param   b  Blue brightness, 0 = minimum (off), 255 = maximum.
  @param   w  White brightness, 0 = minimum (off), 255 = maximum, ignored
              if using RGB pixels.
*/
void Adafruit_NeoPixel::setPixelColor(
    uint16_t n, uint8_t r, uint8_t g, uint8_t b, uint8_t w)
{

  if (n < numLEDs)
  {
    if (brightness)
    { // See notes in setBrightness()
      r = (r * brightness) >> 8;
      g = (g * brightness) >> 8;
      b = (b * brightness) >> 8;
      w = (w * brightness) >> 8;
    }
    uint8_t *p;
    if (wOffset == rOffset)
    {                     // Is an RGB-type strip
      p = &pixels[n * 3]; // 3 bytes per pixel (ignore W)
    }
    else
    {                     // Is a WRGB-type strip
      p = &pixels[n * 4]; // 4 bytes per pixel
      p[wOffset] = w;     // Store W
    }
    p[rOffset] = r; // Store R,G,B
    p[gOffset] = g;
    p[bOffset] = b;
  }
}

/*!
  @brief   Set a pixel's color using a 32-bit 'packed' RGB or RGBW value.
  @param   n  Pixel index, starting from 0.
  @param   c  32-bit color value. Most significant byte is white (for RGBW
              pixels) or ignored (for RGB pixels), next is red, then green,
              and least significant byte is blue.
*/
void Adafruit_NeoPixel::setPixelColor(uint16_t n, uint32_t c)
{
  if (n < numLEDs)
  {
    uint8_t *p,
        r = (uint8_t)(c >> 16),
        g = (uint8_t)(c >> 8),
        b = (uint8_t)c;
    if (brightness)
    { // See notes in setBrightness()
      r = (r * brightness) >> 8;
      g = (g * brightness) >> 8;
      b = (b * brightness) >> 8;
    }
    if (wOffset == rOffset)
    {
      p = &pixels[n * 3];
    }
    else
    {
      p = &pixels[n * 4];
      uint8_t w = (uint8_t)(c >> 24);
      p[wOffset] = brightness ? ((w * brightness) >> 8) : w;
    }
    p[rOffset] = r;
    p[gOffset] = g;
    p[bOffset] = b;
  }
}

/*!
  @brief   Fill all or part of the NeoPixel strip with a color.
  @param   c      32-bit color value. Most significant byte is white (for
                  RGBW pixels) or ignored (for RGB pixels), next is red,
                  then green, and least significant byte is blue. If all
                  arguments are unspecified, this will be 0 (off).
  @param   first  Index of first pixel to fill, starting from 0. Must be
                  in-bounds, no clipping is performed. 0 if unspecified.
  @param   count  Number of pixels to fill, as a positive value. Passing
                  0 or leaving unspecified will fill to end of strip.
*/
void Adafruit_NeoPixel::fill(uint32_t c, uint16_t first, uint16_t count)
{
  uint16_t i, end;

  if (first >= numLEDs)
  {
    return; // If first LED is past end of strip, nothing to do
  }

  // Calculate the index ONE AFTER the last pixel to fill
  if (count == 0)
  {
    // Fill to end of strip
    end = numLEDs;
  }
  else
  {
    // Ensure that the loop won't go past the last pixel
    end = first + count;
    if (end > numLEDs)
      end = numLEDs;
  }

  for (i = first; i < end; i++)
  {
    this->setPixelColor(i, c);
  }
}

/*!
  @brief   Convert hue, saturation and value into a packed 32-bit RGB color
           that can be passed to setPixelColor() or other RGB-compatible
           functions.
  @param   hue  An unsigned 16-bit value, 0 to 65535, representing one full
                loop of the color wheel, which allows 16-bit hues to "roll
                over" while still doing the expected thing (and allowing
                more precision than the wheel() function that was common to
                prior NeoPixel examples).
  @param   sat  Saturation, 8-bit value, 0 (min or pure grayscale) to 255
                (max or pure hue). Default of 255 if unspecified.
  @param   val  Value (brightness), 8-bit value, 0 (min / black / off) to
                255 (max or full brightness). Default of 255 if unspecified.
  @return  Packed 32-bit RGB with the most significant byte set to 0 -- the
           white element of WRGB pixels is NOT utilized. Result is linearly
           but not perceptually correct, so you may want to pass the result
           through the gamma32() function (or your own gamma-correction
           operation) else colors may appear washed out. This is not done
           automatically by this function because coders may desire a more
           refined gamma-correction function than the simplified
           one-size-fits-all operation of gamma32(). Diffusing the LEDs also
           really seems to help when using low-saturation colors.
*/
uint32_t Adafruit_NeoPixel::ColorHSV(uint16_t hue, uint8_t sat, uint8_t val)
{

  uint8_t r, g, b;

  // Remap 0-65535 to 0-1529. Pure red is CENTERED on the 64K rollover;
  // 0 is not the start of pure red, but the midpoint...a few values above
  // zero and a few below 65536 all yield pure red (similarly, 32768 is the
  // midpoint, not start, of pure cyan). The 8-bit RGB hexcone (256 values
  // each for red, green, blue) really only allows for 1530 distinct hues
  // (not 1536, more on that below), but the full unsigned 16-bit type was
  // chosen for hue so that one's code can easily handle a contiguous color
  // wheel by allowing hue to roll over in either direction.
  hue = (hue * 1530L + 32768) / 65536;
  // Because red is centered on the rollover point (the +32768 above,
  // essentially a fixed-point +0.5), the above actually yields 0 to 1530,
  // where 0 and 1530 would yield the same thing. Rather than apply a
  // costly modulo operator, 1530 is handled as a special case below.

  // So you'd think that the color "hexcone" (the thing that ramps from
  // pure red, to pure yellow, to pure green and so forth back to red,
  // yielding six slices), and with each color component having 256
  // possible values (0-255), might have 1536 possible items (6*256),
  // but in reality there's 1530. This is because the last element in
  // each 256-element slice is equal to the first element of the next
  // slice, and keeping those in there this would create small
  // discontinuities in the color wheel. So the last element of each
  // slice is dropped...we regard only elements 0-254, with item 255
  // being picked up as element 0 of the next slice. Like this:
  // Red to not-quite-pure-yellow is:        255,   0, 0 to 255, 254,   0
  // Pure yellow to not-quite-pure-green is: 255, 255, 0 to   1, 255,   0
  // Pure green to not-quite-pure-cyan is:     0, 255, 0 to   0, 255, 254
  // and so forth. Hence, 1530 distinct hues (0 to 1529), and hence why
  // the constants below are not the multiples of 256 you might expect.

  // Convert hue to R,G,B (nested ifs faster than divide+mod+switch):
  if (hue < 510)
  { // Red to Green-1
    b = 0;
    if (hue < 255)
    { //   Red to Yellow-1
      r = 255;
      g = hue; //     g = 0 to 254
    }
    else
    {                //   Yellow to Green-1
      r = 510 - hue; //     r = 255 to 1
      g = 255;
    }
  }
  else if (hue < 1020)
  { // Green to Blue-1
    r = 0;
    if (hue < 765)
    { //   Green to Cyan-1
      g = 255;
      b = hue - 510; //     b = 0 to 254
    }
    else
    {                 //   Cyan to Blue-1
      g = 1020 - hue; //     g = 255 to 1
      b = 255;
    }
  }
  else if (hue < 1530)
  { // Blue to Red-1
    g = 0;
    if (hue < 1275)
    {                 //   Blue to Magenta-1
      r = hue - 1020; //     r = 0 to 254
      b = 255;
    }
    else
    { //   Magenta to Red-1
      r = 255;
      b = 1530 - hue; //     b = 255 to 1
    }
  }
  else
  { // Last 0.5 Red (quicker than % operator)
    r = 255;
    g = b = 0;
  }

  // Apply saturation and value to R,G,B, pack into 32-bit result:
  uint32_t v1 = 1 + val;  // 1 to 256; allows >>8 instead of /255
  uint16_t s1 = 1 + sat;  // 1 to 256; same reason
  uint8_t s2 = 255 - sat; // 255 to 0
  return ((((((r * s1) >> 8) + s2) * v1) & 0xff00) << 8) |
         (((((g * s1) >> 8) + s2) * v1) & 0xff00) |
         (((((b * s1) >> 8) + s2) * v1) >> 8);
}

/*!
  @brief   Query the color of a previously-set pixel.
  @param   n  Index of pixel to read (0 = first).
  @return  'Packed' 32-bit RGB or WRGB value. Most significant byte is white
           (for RGBW pixels) or 0 (for RGB pixels), next is red, then green,
           and least significant byte is blue.
  @note    If the strip brightness has been changed from the default value
           of 255, the color read from a pixel may not exactly match what
           was previously written with one of the setPixelColor() functions.
           This gets more pronounced at lower brightness levels.
*/
uint32_t Adafruit_NeoPixel::getPixelColor(uint16_t n) const
{
  if (n >= numLEDs)
    return 0; // Out of bounds, return no color.

  uint8_t *p;

  if (wOffset == rOffset)
  { // Is RGB-type device
    p = &pixels[n * 3];
    if (brightness)
    {
      // Stored color was decimated by setBrightness(). Returned value
      // attempts to scale back to an approximation of the original 24-bit
      // value used when setting the pixel color, but there will always be
      // some error -- those bits are simply gone. Issue is most
      // pronounced at low brightness levels.
      return (((uint32_t)(p[rOffset] << 8) / brightness) << 16) |
             (((uint32_t)(p[gOffset] << 8) / brightness) << 8) |
             ((uint32_t)(p[bOffset] << 8) / brightness);
    }
    else
    {
      // No brightness adjustment has been made -- return 'raw' color
      return ((uint32_t)p[rOffset] << 16) |
             ((uint32_t)p[gOffset] << 8) |
             (uint32_t)p[bOffset];
    }
  }
  else
  { // Is RGBW-type device
    p = &pixels[n * 4];
    if (brightness)
    { // Return scaled color
      return (((uint32_t)(p[wOffset] << 8) / brightness) << 24) |
             (((uint32_t)(p[rOffset] << 8) / brightness) << 16) |
             (((uint32_t)(p[gOffset] << 8) / brightness) << 8) |
             ((uint32_t)(p[bOffset] << 8) / brightness);
    }
    else
    { // Return raw color
      return ((uint32_t)p[wOffset] << 24) |
             ((uint32_t)p[rOffset] << 16) |
             ((uint32_t)p[gOffset] << 8) |
             (uint32_t)p[bOffset];
    }
  }
}

/*!
  @brief   Adjust output brightness. Does not immediately affect what's
           currently displayed on the LEDs. The next call to show() will
           refresh the LEDs at this level.
  @param   b  Brightness setting, 0=minimum (off), 255=brightest.
  @note    This was intended for one-time use in one's setup() function,
           not as an animation effect in itself. Because of the way this
           library "pre-multiplies" LED colors in RAM, changing the
           brightness is often a "lossy" operation -- what you write to
           pixels isn't necessary the same as what you'll read back.
           Repeated brightness changes using this function exacerbate the
           problem. Smart programs therefore treat the strip as a
           write-only resource, maintaining their own state to render each
           frame of an animation, not relying on read-modify-write.
*/
void Adafruit_NeoPixel::setBrightness(uint8_t b)
{
  // Stored brightness value is different than what's passed.
  // This simplifies the actual scaling math later, allowing a fast
  // 8x8-bit multiply and taking the MSB. 'brightness' is a uint8_t,
  // adding 1 here may (intentionally) roll over...so 0 = max brightness
  // (color values are interpreted literally; no scaling), 1 = min
  // brightness (off), 255 = just below max brightness.
  uint8_t newBrightness = b + 1;
  if (newBrightness != brightness)
  { // Compare against prior value
    // Brightness has changed -- re-scale existing data in RAM,
    // This process is potentially "lossy," especially when increasing
    // brightness. The tight timing in the WS2811/WS2812 code means there
    // aren't enough free cycles to perform this scaling on the fly as data
    // is issued. So we make a pass through the existing color data in RAM
    // and scale it (subsequent graphics commands also work at this
    // brightness level). If there's a significant step up in brightness,
    // the limited number of steps (quantization) in the old data will be
    // quite visible in the re-scaled version. For a non-destructive
    // change, you'll need to re-render the full strip data. C'est la vie.
    uint8_t c,
        *ptr = pixels,
        oldBrightness = brightness - 1; // De-wrap old brightness value
    uint16_t scale;
    if (oldBrightness == 0)
      scale = 0; // Avoid /0
    else if (b == 255)
      scale = 65535 / oldBrightness;
    else
      scale = (((uint16_t)newBrightness << 8) - 1) / oldBrightness;
    for (uint16_t i = 0; i < numBytes; i++)
    {
      c = *ptr;
      *ptr++ = (c * scale) >> 8;
    }
    brightness = newBrightness;
  }
}

/*!
  @brief   Retrieve the last-set brightness value for the strip.
  @return  Brightness value: 0 = minimum (off), 255 = maximum.
*/
uint8_t Adafruit_NeoPixel::getBrightness(void) const
{
  return brightness - 1;
}

/*!
  @brief   Fill the whole NeoPixel strip with 0 / black / off.
*/
void Adafruit_NeoPixel::clear(void)
{
  memset(pixels, 0, numBytes);
}

// A 32-bit variant of gamma8() that applies the same function
// to all components of a packed RGB or WRGB value.
uint32_t Adafruit_NeoPixel::gamma32(uint32_t x)
{
  uint8_t *y = (uint8_t *)&x;
  // All four bytes of a 32-bit value are filtered even if RGB (not WRGB),
  // to avoid a bunch of shifting and masking that would be necessary for
  // properly handling different endianisms (and each byte is a fairly
  // trivial operation, so it might not even be wasting cycles vs a check
  // and branch for the RGB case). In theory this might cause trouble *if*
  // someone's storing information in the unused most significant byte
  // of an RGB value, but this seems exceedingly rare and if it's
  // encountered in reality they can mask values going in or coming out.
  for (uint8_t i = 0; i < 4; i++)
    y[i] = gamma8(y[i]);
  return x; // Packed 32-bit return
}