This is the source code and hardware design for a model vehicle platform developed and maintained by the VESC project (formerly at RISE Research Institutes of Sweden). The platform has support for cars with Ackermann steering, robots with differential steering and partial support for quadcopters.
Self-Driving in this context means that the vehicles can follow a pre-programmed path outdoors accurately using RTK-GNSS. The paths can be edited using RControlStation as a set of points with different time stamps or velocities, depending on the mode. It is also possible to send paths to the vehicles with time stamps in real-time from external applications (either using UDP or TCP to RControlStation, or directly over a radio link) for e.g. following other vehicles.
Some details about the position estimation and the autopilot can be found in our published article.
Figure 1 shows a screenshot of RControlStation, which is a GUI where model vehicles can be viewed, configured and controlled in real time.
Here is a (quire outdated) video with a test of VESC SDVP on a model car:
The repository is organized as follows:
- Documentation
Contains Markdown files with documentation and tutorials, and the directories:- PDF
Contains generated PDFs from the markdown files. Will be cleared when the documentation is built. - Pictures
Contains photos and drawings, which are referenced in the documentation files.
- PDF
- Embedded
Contains embedded software for various PCBs of the platform.- Mote
The software for the mote PCB, which can be used as a USB-to-802.15.4 bridge to communicate with the model cars. - RC_Controller
The software for the control PCB. This is where the sensor fusion, position estimation and autopilot for the car runs. - uwb_board
The software for the Ultra-wideband ranging boards.
- Mote
- Hardware
KiCad PCB projects with the PCBs for the platform.- Controller
The PCB that is referred to as the controller in this documentation. The RC_Controller software runs on this one, and this is the main PCB that this platform is built on. - RFMote_PA
The USB-to-802.15.4 bridge mentioned above. Note that if an IP-connection with e.g. a raspberry pi is used, this one is not needed. - uwb_pcb
A PCB with a DWM1000 module, a STM32F4 microcontroller, a MPU9250 IMU, a CAN-transceiver and some DC/DC converters. The uwb_board software mentioned above runs on this one. This PCB is not needed, but it is useful for experimenting with UWB positioning.
- Controller
- Linux
Contains Linux software, mostly written using the Qt framework, for the platform.- Car_Client
This is a Qt command line program that can run on e.g. a raspberry pi, which is connected to the Controller PCB over USB. Car_Client provides a TCP bridge, which can be used to access the Controller over a network connection instead of a radio. Car_Client also runs the Chronos software (which might be documented later) and can simulate cars for development without having access to a model car. Car_Client can also connect to cameras supported by Video For Linux (V4L) and stream them as JPEG images to RControlStation. - RControlStation
This is a desktop program that can stream realtime data from the cars (including video), and edit trajectories for the model cars on top of OpenStreetMap. It can also act as a RTK base station, or connect to one. There are also many other functions, such as providing a TCP bridge to control cars and even emulating GPS signal using software-defined radio. It is a Qt Creator project, install the following packages under Ubuntu 18.04 or later to build it:build-essential qtcreator qt5-default qtquickcontrols2-5-dev qtdeclarative5-dev libqt5serialport5-dev - RControlStationComm
A C library that can be used to interface cars and trajectories from RControlStation, when using the TCP server in RControlStation. - CarNetworkTester
A test program where XML messages that can be decoded by RControlStation can be generated and sent, and the response can be studied. Useful for developing independent programs that interface with RControlStation and the model cars over TCP. - scala_test
Scala and java-based software to perform automatic testing of the model cars in real-time using ScalaCheck. RControlStationComm is used to interface with the cars and RControlStation. An interactive scala shell where the cars can be controlled, including the ability to generate trajectories to arbitrary points and orientations avoiding static obstacles, is also included. A paper where this is presented in detail is currently being written. - Pi
Scripts and UDEV rules for a raspberry pi (or similar) embedded Linux computer that is installed on a model car and runs Car_Client.
- Car_Client
Figure 2 shows a hardware diagram of a working configuration of the VESC-SDVP platform. The cyan-colored boxes to the left are the components on a model car, and the green boxes to the right are a laptop computer connected over 4G to the model car. The laptop computer also runs a RTK-GNSS base station, so that the model car can position itself with around 3 cm accuracy relative to the GNSS antenna connected to the receiver on the laptop.
Here is a video that shows how a model car like the one in the block diagram above was built:
There are many different configuration of hardware components that can result in a working VESC SDVP model car. What they need to function in general is:
- The Controller, which runs the embedded software that controls the motion and estimates the position of the model car.
- A VESC motor controller that controls the motor on the car over CAN-bus, and provides speed and position estimation from the motor that is used in the sensor fusion in the controller.
- A computer that runs the RControlStation software.
- A way to communicate between the Controller PCB and RControlStation. The options are:
- Using the embedded radios on the controller, and our Radio Mote plugged in over USB to the computer running RControlStation.
- Connecting the controller to an embedded Linux computer using USB, such as the Raspberry PI, and running Car_Client on that computer. Then RControlStation can communicate with the controller over TCP using Car_Client. The TCP connection can then run over a network as usual, such as WiFi or 4G cellular. This is the method that we are using on the setup above.
- Correction data from a RTK-SN base station within 10 km from where the car operates. There is support for different sources of correction data, such as:
- Connecting a supported GNSS receiver, such as the Ublox M8T or Ublox M8P, to the computer running RControlStation, and streaming correction data over that connection. This is what we do in the setup above.
- Connecting to a NTRIP server. This can be done from RControlStation, or by passing an argument to Car_Client if it is used instead of a radio.
- Our Controller in base station mode, where it will transmit correction data over the 433 MHz radio.
- Other things that are (obviously) needed are motor, steering servo, power supplies and antennas.
There is currently support for two different steering geometries: Ackermann and Differential. In Ackermann steering mode there is one main motor driving the car, and a steering servo controlling the direction; whereas in differential mode there is one motor that drives the wheels on each side of the car and there is no steering servo. By default, the controller is configured for Ackermann steering, but that, and many other settings, can be changed in conf_general.h:
// Set to 1 to enable differential steering
#define HAS_DIFF_STEERING 1
// CAN ID of VESC motor controller for the left motor
#define DIFF_STEERING_VESC_LEFT 0
// CAN ID of VESC motor controller for the right motor
#define DIFF_STEERING_VESC_RIGHT 1
In addition to updating conf_general.h, geometry parameters for the car also have to be updated in RControlStation, as shown in Figure 3:
The most important parameters for Ackermann steering are listed in the following table. Some of them are not used in differential steering mode.
| Parameter | Description |
|---|---|
| Gear Ratio | The ratio between one wheel revolution and one motor revolution. |
| Turn Radius | The radius of the circle the car follows at maximum steering angle. |
| Wheel Diameter | Diameter of the model car wheels. |
| Axis Distance | Distance between front and rear wheel axis. |
| Motor Poles | Number of motor poles. Usually 2 or 4 for inrunners. |
| Servo Center | PWM signal to output to steering servo when going straight [0 - 1]. |
| Servo Range | Steering range. Negative numbers invert the servo direction [-1 - 1]. |
It is important to get these parameters correct, as they have a large impact on the position estimation and autopilot.
It is possible to test the platform without having access to any other hardware than a computer. This can be done by running Car_Client with the following flags:
./Car_Client --usetcp --simulatecars 1:0
This will simulate a model car locally, including the autopilot. Then RControlStation can connecto to localhost over TCP and control the simulated car as if it were an actual model car. Car_Client accepts several different flags that affect the simulation; all flags can be listed using the -h argument:
./Car_Client -h
Car_Client can be built with
cd Linux/Car_Client
qmake -qt=5 DEFINES+=HAS_CAMERA
make clean
make
After that Car_Client can be started, and a connection can be made from RControlStation:
./Car_Client -p /dev/ttyACM0 --useudp --logusb --usetcp
RControlStation also supports generation GPS signals using the Lime SDR. This is work in progress and planned to be useful for automatic HIL testing in the future, but it might be nice to play around with if you have access to a Lime SDR. In order to use it, the Lime Suite has to be installed on your system. Once that is done, RControlStation can be build with Lime SDR support by uncommenting the following line in RControlStation.pro:
# Lime SDR support
#DEFINES += HAS_LIME_SDR
Once RControlStation is compiled with Lime SDR support, a real-time GPS simulation can be started from Tests -> GPS Simulator, which will show the dialog in Figure 4:
The desired latitude, longitude and height can then simply be set in the dialog. It is also possible to follow a model car and generate its perceived position. The simulation mode can also be used in combination with the GPS Emulator, making it possible to generate GPS signal for a virtual vehicle in real-time.
- A work-in-progress user guide with several details on how to use RControlStation can be found here.
- A tutorial on how to implement new functionality both in the embedded control software and in RControlStation can be found here
- Our published article