s3-mini-pro-release.yaml

# These substitutions allow the end user to override certain values
substitutions:
  friendly_name: 'S3 Mini Pro'
  node_name: 's3minipro'
  device_name: 's3minipro'
  project_base: 'Lolin Wemos'
  project_name: 'S3 Mini Pro'
  project_version: '1.0'
  device_description: 'I2C(SH1.0-4P); 0.85"TFT(128x128); QMI8658C(6D MEMS IMU)'
# pins
  pin_button_1: '0'
  pin_button_2: '47'
  pin_button_3: '48'
  pin_ir: '9'
  pin_rgb_led: '8'
  pin_rgb_power: '7'
  pin_i2c_sda: '12'
  pin_i2c_scl: '11'
  imu_int_1: '18'
  imu_int_2: '21'
  pin_tx: '43'
  pin_rx: '44'
  pin_ss: '37'
  pin_tft_bl: '33'
  pin_tft_rst: '34'
  pin_tft_cs: '35'
  pin_tft_dc: '36'
  pin_tft_mosi: '38'
  pin_tft_miso: '39'
  pin_tft_sck: '40'

esphome:
  name: $node_name
  friendly_name: $friendly_name
  comment: $device_description
  # This will allow for project identification,
  # configuration and updates.
  project:
    name: ${project_base}.${project_name}
    version: $project_version
  platformio_options:
    board: lolin_s3_mini
    framework: espidf
    board_build.mcu: esp32s3
    board_build.f_cpu: 240000000L
    board_build.f_flash: 80000000L
    board_build.flash_mode: qio
    board_build.arduino.memory_type: qio_opi
    build_flags: [
      "-DBOARD_HAS_PSRAM",
      "-DARDUINO_LOLIN_S3_MINI_PRO",
      ]
    board_build.extra_flags:
      - "-DURL=\\\"https://www.wemos.cc/en/latest/s3/s3_mini_pro.html\\\""
      - "-DVENDOR=\\\"Wemos\\\""
      - "-DUSB_MANUFACTURER_STRING=\\\"Lolin\\\""
      - "-DUSB_PRODUCT_STRING=\\\"S3MiniPro\\\""
      - "-w"
  # Automatically add the mac address to the name
  # so you can use a single firmware for all devices
  name_add_mac_suffix: true

esp32:
  board: lolin_s3_mini
  variant: esp32s3
  flash_size: 4MB
  framework:
    type: esp-idf
    version: latest
    platform_version: 6.6.0
    sdkconfig_options:
      CONFIG_ESPTOOLPY_FLASHFREQ_80M: y
      CONFIG_FLASHMODE_QIO: y
      CONFIG_ESPTOOLPY_FLASHSIZE_DETECT: y
      CONFIG_ESPTOOLPY_AFTER_NORESET: y
      CONFIG_TEMP_SENSOR_SUPPRESS_DEPRECATE_WARN: y
      CONFIG_LWIP_MAX_SOCKETS: '16'
      CONFIG_LWIP_CHECK_THREAD_SAFETY: y
      CONFIG_LWIP_IRAM_OPTIMIZATION: y
      CONFIG_LWIP_EXTRA_IRAM_OPTIMIZATION: y
      CONFIG_BT_BLE_50_FEATURES_SUPPORTED: y
      CONFIG_ESP_TASK_WDT: y
      CONFIG_ESP_TASK_WDT_TIMEOUT_S: '10'
      CONFIG_RMT_ISR_IRAM_SAFE: y
      CONFIG_ESPTOOLPY_FLASHSIZE_4MB: y
      CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_240: y
      CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ: '240'
      CONFIG_ESP32_DEFAULT_CPU_FREQ_240: y
      CONFIG_ESP32S3_DEFAULT_CPU_FREQ_240: y
      CONFIG_COMPILER_OPTIMIZATION: CONFIG_COMPILER_OPTIMIZATION_PERF
      CONFIG_BOOTLOADER_COMPILER_OPTIMIZATION: BOOTLOADER_COMPILER_OPTIMIZATION_PERF
      CONFIG_COMPILER_OPTIMIZATION_CHECKS_SILENT: y
      CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_SILENT: y
      CONFIG_BT_ALLOCATION_FROM_SPIRAM_FIRST: 'y'
      CONFIG_SPIRAM_TRY_ALLOCATE_WIFI_LWIP: y
      CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG: y
      CONFIG_ESP32S3_BROWNOUT_DET: y
      CONFIG_ESP32S3_BROWNOUT_DET_LVL_SEL_7: y
      CONFIG_ESP32S3_BROWNOUT_DET_LVL: '7'

# Enable PSRAM
psram:

# To be able to get logs from the device via serial and api.
logger:
  hardware_uart: USB_SERIAL_JTAG

# API is a requirement of the dashboard import.
api:

# OTA is required for Over-the-Air updating
ota:
  - platform: esphome

# This should point to the public location of this yaml file.
dashboard_import:
  package_import_url: github://velijv/WEMOS_S3_MINI_PRO-ESPHome/s3-mini-pro.yaml@main

wifi:
  # Set up a wifi access point using the device name above
  ap:

# In combination with the `ap` this allows the user
# to provision wifi credentials to the device.
captive_portal:

##########################################################
# Most projects should not remove anything from above here
# and should just modify the name, project name/version
# and git url for the dashboard_import
##########################################################

# Sets up Bluetooth LE (Only on ESP32) to allow the user
# to provision wifi credentials to the device.
esp32_improv:
  authorizer: none

# Sets up the improv via serial client for Wi-Fi provisioning.
# Handy if your device has a usb port for the user to add credentials when they first get it.
improv_serial:
  next_url: https://veli.ee/esphome?device_name={{device_name}}&ip_address={{ip_address}}&esphome_version={{esphome_version}}

##########################################################
# S3_MINI_PRO CONFIG BEGIN
##########################################################
binary_sensor:
- platform: gpio
  pin:
    number: $pin_button_1
    inverted: true
    mode:
      input: true
      pullup: true
    ignore_strapping_warning: true
  name: Button Left
  id: io_${pin_button_1}

- platform: gpio
  pin:
    number: $pin_button_2
    inverted: true
    mode:
      input: true
      pullup: true
  name: Button OK
  id: io_${pin_button_2}

- platform: gpio
  pin:
    number: $pin_button_3
    inverted: true
    mode:
      input: true
      pullup: true
  name: Button Right
  id: io_${pin_button_3}

i2c:
  id: i2c_bus
  sda: $pin_i2c_sda
  scl: $pin_i2c_scl
  scan: true

spi:
  clk_pin: $pin_tft_sck
  mosi_pin: $pin_tft_mosi
  interface: any

display:
    platform: ili9xxx
    id: lcd
    cs_pin: $pin_tft_cs
    dc_pin: $pin_tft_dc
    reset_pin: $pin_tft_rst
    auto_clear_enabled: true
    model: GC9A01A
    dimensions:
      height: 128
      width: 128
      offset_height: 1
      offset_width: 2
    data_rate: 20MHz
    color_order: bgr
    invert_colors: true
    transform:
      mirror_x: true
      mirror_y: true

remote_receiver:
- id: ${device_name}_receiver
  dump: all
  pin:
    number: $pin_ir
    mode:
      input: true

power_supply:
- id: rgb_led_psu
  pin:
    number: $pin_rgb_power
    mode:
      output: true
      pulldown: true
  enable_time: 10ms
  keep_on_time: 50ms
  enable_on_boot: false

output:
  - id: backlight_pwm
    platform: ledc
    frequency: 1220Hz
    pin:
      number: $pin_tft_bl
      mode:
        output: true
        pullup: true
    min_power: 0.1
    max_power: 0.99
    zero_means_zero: true

light:
  - platform: monochromatic
    output: backlight_pwm
    name: Display
    id: backlight
    restore_mode: ALWAYS_ON
    icon: mdi:cellphone-screenshot
    entity_category: config
    default_transition_length: 100ms
    on_turn_on:
      then:
        - component.update: lcd
    on_turn_off:
      then:
        - lambda: |-
            id(${device_name}_leds).turn_on().set_brightness(0.2).set_rgb(1.0, 0.5, 0.0).perform();

  - platform: esp32_rmt_led_strip
    rmt_channel: 3
    chipset: WS2812
    rgb_order: RGB
    pin: $pin_rgb_led
    num_leds: 1
    icon: mdi:developer-board
    id: ${device_name}_leds
    name: IO_${pin_rgb_led}_LED
    entity_category: diagnostic
    disabled_by_default: true
    restore_mode: ALWAYS_OFF
    default_transition_length: 200ms
    power_supply: rgb_led_psu
#    effects: !include
#      file: common/light/effects/single.rgb.yaml


####
# packages:
#   gyro: !include {
#     file: common/sensor/qmi8658c.yaml,
#     vars: {
#       gyro_id: '${gyro_id}',
#       gyro_name: '${gyro_name}',
#       update_interval: '${gyro_update_interval}',
#     }
#   }
####