typos

docs/operation/dcc-ex-native-protocol.rst

@@ -39,20 +39,20 @@ Note this must be preformed *before* you connect to the command station.
 
 * Start |ED|
 * Open the Menu --> Preferences
-* Find the section "Connection Preferences"
-* open the sub-group "DCC-EX EX-CommandStation Preferences"
-* Enable the "Use Native DCC-EX command"
+* Find the section "Connect Preferences"
+* Open the sub-section "DCC-EX EX-CommandStation Preferences"
+* Enable the "Use Native DCC-EX commands"
 * If you also use other brands of Command Station (other than DCC-EX) 
 
    * We recommend that you also enable the "Show protocol option"
 
 * Optionally you can enable a button on the Action Bar in |ED|
 
-   * Close the "DCC-EX EX-CommandStation Preferences" sub-group (touch the Back button), but stay in the preferences
+   * Close the "DCC-EX EX-CommandStation Preferences" sub-group (click the Android Back button), but stay in the preferences
    * Find the "Throttle Screen Action Bar Preferences" section
    * Enable the "DCC-EX button?"
 
-* close preferences (touch the Back button) to go back to the Connect Screen
+* close preferences (click the Android Back button) to go back to the Connect Screen
 
 Now connect to the **DCC-EX EX-CommandStation**
 
@@ -98,7 +98,7 @@ To write CVs of decoders on the Main Track select "Program on Main (Operation Mo
 
 Note that you cannot read CVs or DCC Addresses on the main track.  You can only write CVs of a specified loco (DCC Address).
 
-To write a new CV value, enter the DCC address of the loco you wan to change, enter the CV number into the 'CV' field, enter the new value in the 'Value' field and click :guilabel:`Write`
+To write a new CV value, enter the DCC address of the loco you want to change, enter the CV number into the 'CV' field, enter the new value in the 'Value' field and click :guilabel:`Write`
 
 Optionally, you can use the 'NRMA CVs' pulldown to select a common CV from a list.  This just enters the appropriate CV number in the 'CV' field.
 
@@ -132,8 +132,8 @@ Each of the tracks/channels of the Motor Shield(s) can be changed to any one of
 
 To change the simply select the state in the pulldown in the desired track (or tracks) and click :guilabel:`Set`
 
-Note that if you select `DC` or `DC reversed polarity (DCX)` you must also enter the Address that the track will respond to. 
+Note that if you select `DC` or `DC reversed polarity (DCX)` you must also enter the Address that the track should respond to. 
 
-e.g. if you enter `DC` and address `10` for track 'A", then in the |ED| Select Loco screen, you would need to enter the 'DCC Address' of `10` to control the DC loco on the track would would normally have been the 'Main' track if you were using DCC.
+e.g. if you select `DC` and enter address `10` for track 'A', then in the |ED| Select Loco screen, you would need to enter the 'DCC Address' of `10` to control the DC loco on the track which would normally have been the 'Main' track if you were using DCC.
 
 Note, only one track can ever be selected as 'DCC PROG'

docs/operation/operation.rst

@@ -867,10 +867,10 @@ In general avoid letting |ED| try to run in background.
 
   See the `Background Alert in the Preference page <./preferences.html#background-alert>`_ for information on disabling the alert.
 
-DCC-EX EX-CommandStation- Features when using the Native DCC-EX Protocol
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+DCC-EX - Features when using the Native DCC-EX Protocol
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
-Refer to :doc:`this page <./dcc-ex-native-protocol>` for details on how to use the |ED| features that are only available when using the Native DCC-EX Protocol when connecting to a **DCC-EX EX-CommandStation**.
+Refer to :doc:`this page <./dcc-ex-native-protocol>` for details on how to use the |ED| features that are only available when using the **Native DCC-EX Protocol** when connecting to a **EX-CommandStation**.
 
 
 Exiting Engine Driver