Skip to content

krvprashanth/serv

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

SERV

LibreCores Join the chat at https://gitter.im/librecores/serv CI status Documentation Status

SERV is an award-winning bit-serial RISC-V core

If you want to know more about SERV, what a bit-serial CPU is and what it's good for, I recommend starting out by watching the fantastic short SERV movies

There's also an official SERV user manual with fancy block diagrams, timing diagrams and an in-depth description of how some things work.

Prerequisites

Create a directory to keep all the different parts of the project together. We will refer to this directory as $WORKSPACE from now on. All commands will be run from this directory unless otherwise stated.

Install FuseSoC

pip install fusesoc

Add the FuseSoC standard library

fusesoc library add fusesoc_cores https://github.com/fusesoc/fusesoc-cores

The FuseSoC standard library already contain a version of SERV, but if we want to make changes to SERV, run the bundled example or use the Zephyr support, it is better to add SERV as a separate library into the workspace

fusesoc library add serv https://github.com/olofk/serv

The SERV repo will now be available in $WORKSPACE/fusesoc_libraries/serv. To save some typing, we will refer to that directory as $SERV.

We are now ready to do our first exercises with SERV

If Verilator is installed, we can use that as a linter to check the SERV source code

fusesoc run --target=lint serv

If everything worked, the output should look like

INFO: Preparing ::serv:1.2.0
INFO: Setting up project

INFO: Building simulation model
INFO: Running

Running pre-built test software

Build and run the single threaded zephyr hello world example with verilator (should be stopped with Ctrl-C):

fusesoc run --target=verilator_tb servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_hello.hex

..or... the multithreaded version

fusesoc run --target=verilator_tb servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_hello_mt.hex --memsize=16384

Both should yield an output ending with

***** Booting Zephyr OS zephyr-v1.14.1-4-gc7c2d62513fe *****
Hello World! service

For a more advanced example, we can also run the Dining philosophers demo

fusesoc run --target=verilator_tb servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_phil.hex --memsize=32768

...or... the synchronization example

fusesoc run --target=verilator_tb servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_sync.hex --memsize=16384

Other applications can be tested by compiling and converting to bin and then hex e.g. with makehex.py found in $SERV/sw

Run RISC-V compliance tests

Build the verilator model (if not already done)

fusesoc run --target=verilator_tb --build servant --memsize=8388608

To build the verilator model with MDU (for M extension compliance tests):

fusesoc run --target=verilator_tb --flag=mdu --build servant --memsize=8388608

To build the verilator model with C extension (for Compressed extension compliance tests):

fusesoc run --target=verilator_tb --build servant --memsize=8388608 --compressed=1

Download the tests repo

git clone --branch 2.7.4 https://github.com/riscv-non-isa/riscv-arch-test.git

To run the RISC-V compliance tests, we need to supply the SERV-specific support files and point the test suite to where it can find a target to run (i.e. the previously built Verilator model)

Run the compliance tests

cd riscv-arch-test && make TARGETDIR=$SERV/riscv-target RISCV_TARGET=serv RISCV_DEVICE=I TARGET_SIM=$WORKSPACE/build/servant_1.2.0/verilator_tb-verilator/Vservant_sim

The above will run all tests in the rv32i test suite. Since SERV also implement the M, C, privilege and Zifencei extensions, these can also be tested by choosing any of them instead of I as the RISCV_DEVICE variable.

Run on hardware

The servant SoC has been ported to an increasing number of different FPGA boards. To see all currently supported targets run

fusesoc core show servant

By default, these targets have the program memory preloaded with a small Zephyr hello world example that writes its output on a UART pin. Don't forget to install the appropriate toolchain (e.g. icestorm, Vivado, Quartus...) and add to your PATH

Some targets also depend on functionality in the FuseSoC base library (fusesoc-cores). Running fusesoc library list should tell you if fusesoc-cores is already available. If not, add it to your workspace with

fusesoc library add fusesoc-cores https://github.com/fusesoc/fusesoc-cores

Now we're ready to build. Note, for all the cases below, it's possible to run with --memfile=$SERV/sw/blinky.hex (or any other suitable program) as the last argument to preload the LED blink example instead of hello world.

TinyFPGA BX

Pin A6 is used for UART output with 115200 baud rate.

fusesoc run --target=tinyfpga_bx servant
tinyprog --program build/servant_1.0.1/tinyfpga_bx-icestorm/servant_1.0.1.bin

Icebreaker

Pin 9 is used for UART output with 57600 baud rate.

fusesoc run --target=icebreaker servant

Nexys 2

Pmod pin JA1 is conntected to UART tx with 57600 baud rate. A USB to TTL connector is used to display to hello world message on the serial monitor. (To use blinky.hex change L15 to J14 (led[0]) in data/nexys_2.ucf).

fusesoc run --target=nexys_2_500 servant --uart_baudrate=57600 --firmware=$SERV/sw/zephyr_hello.hex

iCESugar

Pin 6 is used for UART output with 115200 baud rate. Thanks to the onboard debugger, you can just connect the USB Type-C connector to the PC, and a serial console will show up.

fusesoc run --target=icesugar servant

OrangeCrab R0.2

Pin D1 is used for UART output with 115200 baud rate.

fusesoc run --target=orangecrab_r0.2 servant
dfu-util -d 1209:5af0 -D build/servant_1.2.0/orangecrab_r0.2-trellis/servant_1.2.0.bit

Arty A7 35T

Pin D10 (uart_rxd_out) is used for UART output with 57600 baud rate (to use blinky.hex change D10 to H5 (led[4]) in data/arty_a7_35t.xdc).

fusesoc run --target=arty_a7_35t servant

Chameleon96 (Arrow 96 CV SoC Board)

FPGA Pin W14 (1V8, pin 5 low speed connector) is used for UART Tx output with 115200 baud rate. No reset key. Yellow Wifi led is q output.

fusesoc run --target=chameleon96 servant

DE0 Nano

FPGA Pin D11 (Connector JP1, pin 38) is used for UART output with 57600 baud rate. DE0 Nano needs an external 3.3V UART to connect to this pin

fusesoc run --target=de0_nano servant

DE10 Nano

FPGA Pin Y15 (Connector JP7, pin 1) is used for UART output with 57600 baud rate. DE10 Nano needs an external 3.3V UART to connect to this pin

fusesoc run --target=de10_nano servant

DECA development kit

FPGA Pin W18 (Pin 3 P8 connector) is used for UART output with 57600 baud rate. Key 0 is reset and Led 0 q output.

fusesoc run --target=deca servant

EBAZ4205 'Development' Board

Pin B20 is used for UART output with 57600 baud rate. To use blinky.hex change B20 to W14 (red led) in data/ebaz4205.xdc file).

fusesoc run --target=ebaz4205 servant

fusesoc run --target=ebaz4205 servant --memfile=$SERV/sw/blinky.hex

Reference: https://github.com/fusesoc/blinky#ebaz4205-development-board

SoCKit development kit

FPGA Pin F14 (HSTC GPIO addon connector J2, pin 2) is used for UART output with 57600 baud rate.

fusesoc run --target=sockit servant

Saanlima Pipistrello (Spartan6 LX45)

Pin A10 (usb_data<1>) is used for UART output with 57600 baud rate (to use blinky.hex change A10 to V16 (led[0]) in data/pipistrello.ucf).

fusesoc run --target=pipistrello servant

Alhambra II

Pin 61 is used for UART output with 115200 baud rate. This pin is connected to a FT2232H chip in board, that manages the communications between the FPGA and the computer.

fusesoc run --target=alhambra servant
iceprog -d i:0x0403:0x6010:0 build/servant_1.0.1/alhambra-icestorm/servant_1.0.1.bin

iCEstick

Pin 95 is used as the GPIO output which is connected to the board's green LED. Due to this board's limited Embedded BRAM, programs with a maximum of 7168 bytes can be loaded. The default program for this board is blinky.hex.

fusesoc run --target=icestick servant
iceprog build/servant_1.2.0/icestick-icestorm/servant_1.2.0.bin

Nandland Go Board

Pin 56 is used as the GPIO output which is connected to the board's LED1. Due to this board's limited Embedded BRAM, programs with a maximum of 7168 bytes can be loaded. The default program for this board is blinky.hex.

fusesoc run --target=go_board servant
iceprog build/servant_1.2.0/go_board-icestorm/servant_1.2.0.bin

Alinx ax309 (Spartan6 LX9)

Pin D12 (the on-board RS232 TX pin) is used for UART output with 115200 baud rate and wired to Pin P4 (LED0).

fusesoc run --target=ax309 servant

Other targets

The above targets are run on the servant SoC, but there are some targets defined for the CPU itself. Verilator can be run in lint mode to check for design problems by running

fusesoc run --target=lint serv

It's also possible to just synthesise for different targets to check resource usage and such. To do that for the iCE40 devices, run

fusesoc run --tool=icestorm serv --pnr=none

...or to synthesize with vivado for Xilinx targets, run

fusesoc run --tool=vivado serv --pnr=none

This will synthesize for the default Vivado part. To synthesise for a specific device, run e.g.

fusesoc run --tool=vivado serv --pnr=none --part=xc7a100tcsg324-1

Zephyr support

SERV, or rather the Servant SoC, can run the Zephyr RTOS. The Servant-specific drivers and BSP is located in the zephyr subdirectory of the SERV repository. In order to use Zephyr on Servant, a project directory structure must be set up that allows Zephyr to load the Servant-specific files as a module.

First, the Zephyr SDK and the "west" build too must be installed. The Zephyr getting started guide describes these steps in more detail.

Assuming that SERV was installed into $WORKSPACE/fusesoc_libraries/serv as per the prerequisites, run the following command to make the workspace also work as a Zephyr workspace.

west init

Specify the SERV repository as the manifest repository, meaning it will be the main entry point when Zephyr is looking for modules.

west config manifest.path $SERV

Get the right versions of all Zephyr submodules

west update

It should now be possible to build Zephyr applications for the Servant SoC within the workspace. This can be tested e.g. by building the Zephyr Hello world samples application

cd zephyr/samples/hello_world
west build -b service

After a successful build, Zephyr will create an elf and a bin file of the application in build/zephyr/zephyr.{elf,bin}. The bin file can be converted to a verilog hex file, which in turn can be preloaded to FPGA on-chip memories and run on a target board, or loaded into simulated RAM model when running simulations.

To convert the newly built hello world example into a Verilog hex file, run

python3 $SERV/sw/makehex.py zephyr/samples/hello_world/build/zephyr/zephyr.bin 4096 > hello.hex

4096 is the number of 32-bit words to write and must be at least the size of the application binary. hello.hex is the resulting hex file. Running a simulation can now be done as described in Running pre-built test software, e.g.

fusesoc run --target=verilator_tb servant --uart_baudrate=57600 --firmware=/path/to/hello.hex

Or to create an FPGA image with the application preloaded to on-chip RAM, e.g. for a Nexys A7 board, run

fusesoc run --target=nexys_a7 servant --memfile=/path/to/hello.hex

Good to know

Don't feed serv any illegal instructions after midnight. Many logic expressions are hand-optimized using the old-fashioned method with Karnaugh maps on paper, and shamelessly take advantage of the fact that some opcodes aren't supposed to appear. As serv was written with 4-input LUT FPGAs as target, and opcodes are 5 bits, this can save quite a bit of resources in the decoder.

The bus interface is kind of Wishbone, but with most signals removed. There's an important difference though. Don't send acks on the instruction or data buses unless serv explicitly asks for something by raising its cyc signal. Otherwise serv becomes very confused.

Don't go changing the clock frequency on a whim when running Zephyr. Or well, it's ok I guess, but since the UART is bitbanged, this will change the baud rate as well. As of writing, the UART is running at 115200 baud rate when the CPU is 32 MHz. There are two NOPs in the driver to slow it down a bit, so if those are removed I think it could achieve baud rate 115200 on a 24MHz clock.. in case someone wants to try

TODO

  • Applications have to be preloaded to RAM at compile-time
  • Make it faster and smaller

About

SERV - The SErial RISC-V CPU

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • Verilog 82.4%
  • C 5.9%
  • C++ 4.5%
  • Tcl 2.0%
  • SystemVerilog 1.7%
  • Assembly 1.7%
  • Other 1.8%