ECPIX-5 Tester

FT4232

Test by pluging USB2 to PC:

$ sudo dmesg -w

[968380.785032] usb 5-1.1.4.4: new high-speed USB device number 19 using xhci_hcd
[968380.956022] usb 5-1.1.4.4: New USB device found, idVendor=0403, idProduct=6011, bcdDevice= 8.00
[968380.956025] usb 5-1.1.4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[968380.956027] usb 5-1.1.4.4: Product: Quad RS232-HS
[968380.956028] usb 5-1.1.4.4: Manufacturer: FTDI
[968381.264162] ftdi_sio 5-1.1.4.4:1.0: FTDI USB Serial Device converter detected
[968381.264176] usb 5-1.1.4.4: Detected FT4232H
[968381.264437] usb 5-1.1.4.4: FTDI USB Serial Device converter now attached to ttyUSB0
[968381.264599] ftdi_sio 5-1.1.4.4:1.1: FTDI USB Serial Device converter detected
[968381.264609] usb 5-1.1.4.4: Detected FT4232H
[968381.264963] usb 5-1.1.4.4: FTDI USB Serial Device converter now attached to ttyUSB1
[968381.265110] ftdi_sio 5-1.1.4.4:1.2: FTDI USB Serial Device converter detected
[968381.265119] usb 5-1.1.4.4: Detected FT4232H
[968381.265313] usb 5-1.1.4.4: FTDI USB Serial Device converter now attached to ttyUSB2
[968381.265495] ftdi_sio 5-1.1.4.4:1.3: FTDI USB Serial Device converter detected
[968381.265505] usb 5-1.1.4.4: Detected FT4232H
[968381.265718] usb 5-1.1.4.4: FTDI USB Serial Device converter now attached to ttyUSB3

$ minicom --baudrate 1000000 -D /dev/ttyUSB2
    No Hardware flow control
    
$ openFPGALoader --cable ft4232 --bitstream release/top_45.bit

Flash SPI

$ openFPGALoader --cable ft4232 --write-flash --bitstream release/top_45.bit 
write to flash
Jtag frequency : requested 6.00MHz   -> real 6.00MHz
Enable configuration: DONE
SRAM erase: DONE
Open file DONE
Parse file DONE
Detail: 
Jedec ID          : 9d
memory type       : 60
memory capacity   : 19
EDID + CFD length : 9d
EDID              : 1960
CFD               : 
Erasing: [==================================================] 100.00%
Done
Writing: [==================================================] 100.00%
Done
Refresh: DONE

RGB LEDs

Visual test: 4 LEDs blinking Red, Green, Blue.

PMOD

Test with 7 segment: Blinking "8" on all PMODs.

SDCard

Test with 7 segment + SDcard flex and breakout: Blinking "0".

DDR

--========== Initialization ============--
Initializing SDRAM @0x40000000...
Switching SDRAM to software control.
Read leveling:
  m0, b00: |11100000| delays: 01+-01
  m0, b01: |00000000| delays: -
  m0, b02: |00000000| delays: -
  m0, b03: |00000000| delays: -
  best: m0, b00 delays: 01+-01
  m1, b00: |11100000| delays: 01+-01
  m1, b01: |00000000| delays: -
  m1, b02: |00000000| delays: -
  m1, b03: |00000000| delays: -
  best: m1, b00 delays: 01+-01
Switching SDRAM to hardware control.
Memtest at 0x40000000 (2.0MiB)...
  Write: 0x40000000-0x40200000 2.0MiB
   Read: 0x40000000-0x40200000 2.0MiB
Memtest OK
Memspeed at 0x40000000 (Sequential, 2.0MiB)...
  Write speed: 10.7MiB/s
   Read speed: 9.3MiB/s

ULPI

Test by pluging USB-C to PC::

$ sudo dmesg -w

[968390.653012] usb 5-1.1.3: New USB device found, idVendor=16d0, idProduct=0f3b, bcdDevice= 0.00
[968390.653014] usb 5-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[968390.653015] usb 5-1.1.3: Product: Test Device
[968390.653016] usb 5-1.1.3: Manufacturer: LUNA
[968390.653017] usb 5-1.1.3: SerialNumber: 1234

USB-C

Not tested.

HDMI

Test with screen.

Ethernet

Test with cable. Need both LEDs Orange and Green for gigabit link.

Sata

Not tested.