Skip to content

leandrolanzieri/stm32loader

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

STM32Loader

Python script to upload or download firmware to / from ST Microelectronics STM32 microcontrollers over UART.

Also supports ST BlueNRG devices, and the SweetPeas bootloader for Wiznet W7500.

Compatible with Python version 3.2 to 3.7 or 2.7.

Usage

./stm32loader.py [-hqVewvrsRB] [-l length] [-p port] [-b baud] [-P parity] [-a address] [-g address] [-f family] [file.bin]
    -e          Erase (note: this is required on previously written memory)
    -u          Readout unprotect
    -w          Write file content to flash
    -v          Verify flash content versus local file (recommended)
    -r          Read from flash and store in local file
    -l length   Length of read
    -p port     Serial port (default: /dev/tty.usbserial-ftCYPMYJ)
    -b baud     Baud speed (default: 115200)
    -a address  Target address (default: 0x08000000)
    -g address  Start executing from address (0x08000000, usually)
    -f family   Device family to read out device UID and flash size; e.g F1 for STM32F1xx

    -h          Print this help text
    -q          Quiet mode
    -V          Verbose mode

    -s          Swap RTS and DTR: use RTS for reset and DTR for boot0
    -R          Make reset active high
    -B          Make boot0 active high
    -u          Readout unprotect
    -P parity   Parity: "even" for STM32 (default), "none" for BlueNRG

Example

stm32loader.py -e -w -v somefile.bin

This will pre-erase flash, write somefile.bin to the flash on the device, and then perform a verification after writing is finished.

Reference documents

  • ST AN2606: STM32 microcontroller system memory boot mode
  • ST AN3155: USART protocol used in the STM32 bootloader
  • ST AN4872: BlueNRG-1 and BlueNRG-2 UART bootloader protocol

Acknowledgement

Original Version by Ivan A-R (tuxotronic.org). Contributions by Domen Puncer, James Snyder, Floris Lambrechts, Atokulus.

Inspiration for features from:

Electrically

The below assumes you are connecting an STM32F10x. For other chips, the serial pins and/or the BOOT0 / BOOT1 values may differ.

Make the following connections:

  • Serial adapter GND to MCU GND.
  • Serial adapter power to MCU power or vice versa (either 3.3 or 5 Volt).
  • Note if you're using 5 Volt signaling or 3V3 on the serial adapter.
  • Serial TX to MCU RX (PA10).
  • Serial RX to MCU TX (PA9).
  • Serial DTR to MCU RESET.
  • Serial RTS to MCU BOOT0 (or BOOT0 to 3.3V).
  • MCU BOOT1 to GND.

If either RTS or DTR are not available on your serial adapter, you'll have to manually push buttons or work with jumpers. When given a choice, set BOOT0 manually high and drive reset through the serial adepter (it needs to toggle, whereas BOOT0 does not).

Not currently supported

  • Extended erase with specific sectors
  • Command-line argument for readout protection
  • Command-line argument for write protection/unprotection
  • STM8 devices (ST UM0560)
  • Other bootloader protocols (e.g. I2C, HEX -> implemented in stm32flash)

About

Flash firmware to STM32 microcontrollers using Python.

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • Python 100.0%