Skip to content

A Raspberry Pi Grafana dashboard to monitor network health via Prometheus and Telegraf data.

Notifications You must be signed in to change notification settings

mike-weiner/pinet

Repository files navigation

Raspberry Pi Network Monitor

This repository includes instructions and configuration files for setting up a Raspberry Pi to monitor a network's connectivity status via a Grafana Dashboard through Prometheus and Telegraf data collection.

Motivation for this Project

Network Diagram

I recently moved to a more rural location in Minnesota that does not have buried coper or fiber internet infrastructure. Instead, our internet connection comes from a fixed wireless signal. Verizon has a good explanation of the technology here, if you are not familiar.

The unique part about my location is that the house we live in does not have a direct line of sight with our ISP's closest basestation, but another building on the property does. So, our ISP placed their antenna (a Ubiquiti LiteBeam 60) that captures their external internet connection on that building. That signal is then passed into a switch where a MikroTik Cube Lite 60 repeats the signal back to our home. Another MikroTik Cube Lite 60 that is located on our house captures the repeated signal and passes it into our home network's router.

Fore the most part, our experience has been pretty good. Speeds are about 100Mbps down and 50Mbps up with ping times averaging right around 10ms. Keep in mind, we came from a city where we had buried copper that got 500Mbps down and 20Mbps up. We have run into some periods of high latency in our home network (Network 2 in the diagram above) and some intermittent connectivity drops that been reported by our Ubiquiti Dream Machine Pro.

We wanted to begin collecting data about the health of our network to try and give our ISP data confirming our issues. However, our network set up has more points of failure than most home networks. In areas where buried fiber or copper lines are run into a house, the usual culprits of a bad internet connection are the router or modem and both are found right inside your home. This makes it fairly easy for you and/or your ISP to diagnose network issues. With our setup, the antenna that captures the external internet connection could be down. One or both of the repeaters could be down. There could be some combination of both, or it could be our home router. These devices are scattered across two buildings.

Knowing whether or not there was an internet connection in the building 500ft away from our house (Network 1 in the diagram above) was going to give us the best information. We could immediately narrow a loss of connectivity in our house to an issue with the antenna capturing the broader internet or if there was an issue with one (or both) of our repeaters. The challenge is that these are two separate networks. We wanted a local device in the second building that we could access remotely to view historical and current ping times. This is where the Raspberry Pi comes in. We can use a Raspberry Pi that runs a local Grafana dashboard to display network statistics from data collected by locally running Prometheus and Telegraf services. Using Cloudflare Tunnels, we could securely make this dashboard available publicly to us. All of this can be down without having to pay for any services.

Now, I do realize that if the Raspberry Pi does not have an internet connection that we won't be able to reach our Raspberry Pi's Grafana dashboard via the Cloudflare Tunnel. That's fine. That will immediately tell us that we have an issue with the external antenna capturing our boarder internet signal. If we can reach the Raspberry Pi and it's reporting normal ping times, but we don't have an internet connection in our house - then we either have an issue with our repeaters or our local router. This can easily be tracked down since our Ubiquiti Dream Machine Pro will inform us whether it has an internet signal or not. The Raspberry Pi also gives us the flexibility to connect a red LED light that would get turned on if the Pi doesn't have an internet connection.

Don't feel like you can't use this project in your own home network if your house as a buried copper or fiber line. This could be a great project to set up in you want more data about your network and prove to your ISP that you are having issues.

Warning

Since the Raspberry Pi will be sending pings 24/7, leaving it running will consume some amount of network data. Exactly how much data will depend on how many different external services you ping, how frequently you ping them, and how many packets you send with each ping session. If you ISP imposes data limits, be careful to ensure that your project won't tear through your data limit!

Preparing the Raspberry Pi

We first need to get our Raspberry Pi up and running. That starts with flashing a MicroSD card with Raspberry Pi OS and booting into our machine.

Installing Raspberry Pi OS

Raspberry Pi has some excellent documentation about all of the ways that you can get Raspberry Pi OS installed on your Pi. That documentation is found here: https://www.raspberrypi.com/documentation/computers/getting-started.html#using-raspberry-pi-imager

I used Raspberry Pi Imager to flash my MicroSD card and install Raspberry Pi OS. Once you download Raspberry Pi Imager:

  • Select the OS version that you want to install.
    • Note: I chose to install the 64-Bit ARM version on my Raspberry Bi 3 B+.
  • Select the MicroSD card that you want to flash.
  • Click Write.

Don't worry about changing or enabling any of the advanced installation options, if you don't want to. We will configure all of the settings that we need in the next step.

This process will probably take several minutes to complete.

Configuring Raspberry Pi OS on First Boot

Once your MicroSD card is flashed with your selected version of Raspberry Pi OS, insert your MicroSD into your Raspberry Pi, connect a monitor, keyboard, mouse, and plug in your Raspberry Pi to boot it up!

During the first boot, you will need to do some last configuration of the OS. When prompted:

  • If you are using a wireless keyboard and/or mouse, you will first be prompted to get those connected.
  • Select your correct Country, Language, and Timezone.
  • Enter in a Username and Password. This username and password will be used to log into the Pi.
    • Note: Your username can be whatever you like. Make sure that you write down what your username is as we will need it for a later step. My best recommendation is to keep it simple with all lowercase letters, no spaces, no special characters, and no numbers. If you really can't think of something, you could use the default username of pi. I would really not recommend this for security reasons though.
  • Adjust the settings for your Desktop (if needed).
  • If you are not using a wired Ethernet connection, you will be prompted to enter your Wi-Fi security credentials.
  • Finally, you will be prompted to check for any Raspberry Pi OS Updates. Be sure to do this.

Once your configuration is complete, you will be taken to your Desktop. Congrats! You now have your own Raspberry Pi.

There are just two settings that we need to enable.

Enabling Auto Login

To enable Auto Login, in the top-left corner of your Desktop menu bar find the Raspberry Pi Logo. Then:

  • Select Raspberry Pi Configuration from the dropdown.
  • Inside the window that opens, select the System tab.
  • Toggle Auto login to On.

Enabling this setting is not required. The reason for enabling this setting is to prevent having to enter your username and password every time the Pi has to restart or boot up. If you are installing your Raspberry Pi within your own home, it is probably safe to enable this setting. If you are installing your Pi in any public place, I would leave this setting disabled.

Enabling SSH-ing

To enable SSH, in the top-left corner of your Desktop menu bar find the Raspberry Pi Logo. Then:

  • Select Raspberry Pi Configuration from the dropdown.
  • Inside the window that opens, select the Interfaces tab.
  • Toggle SSH to On.

Again, enabling this setting is not required. The reason for enabling this setting is to be able to remote into your machine if there are ever any issues with it.

Updating Packages

The last thing that we need to do is run a quick check to ensure that all of the packages provided with Raspberry Pi OS are update to do.

This is easily done by:

  • Opening a terminal window.
  • Input sudo apt update and press Enter.
  • Input sudo full-upgrade and press Enter.

This process should take no longer than a few minutes to complete.

We are now ready to begin to install and setup the infrastructure that is going to support your network monitoring dashboard!

Setting Up Prometheus

Prometheus Website: https://prometheus.io

Github Repository: https://github.com/prometheus/prometheus/

Prometheus is a monitoring system that can collect data from specific targets at specific intervals. This is exactly how we are going to routinely collect the network data that Telegraf is going to provide. We can then use Prometheus as a source of data within our Grafana dashboard!

Installing Prometheus

At the time of writing, the long-term supported version of Prometheus is 2.37.6. That is the version of Prometheus that I will be installing. All of the v2.37.6 downloads can be found at: https://github.com/prometheus/prometheus/releases/tag/v2.37.6.

If you are looking for a different release, all releases can be found at https://github.com/prometheus/prometheus/releases or at https://prometheus.io/download/.

Since I installed the 64-bit ARM version of Raspberry Pi OS, I will be installing the linux-arm64 version of Prometheus. You will need to install the correct version of Prometheus based on the version and type of OS on your own Raspberry Pi.

Installing Prometheus can be done with a few simple commands via the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input cd ~ and press Enter.
    • Note: This command will move you to your home directory. This is where we will install Prometheus.
  • Input wget https://github.com/prometheus/prometheus/releases/download/v2.37.6/prometheus-2.37.6.linux-arm64.tar.gz and press Enter.
    • Note: This could take a minute or two to download - depending on your internet speeds.
  • Input tar xfz prometheus-2.37.6.linux-arm64.tar.gz and press Enter.
  • Input mv prometheus-2.37.6.linux-arm64.tar.gz/ prometheus/ and press Enter.
  • Input rm prometheus-2.37.6.linux-arm64.tar.gz and press Enter.

After running these commands, you should see a prometheus folder within your home directory. You can double check this by running ls -l. Within the list of folders and files, you should see a prometheus entry.

Creating a Prometheus Service

We want Prometheus to start up as soon as Raspberry Pi boots up. We can do this easily by creating a service for Prometheus. You can learn more about Linux Services here: https://manpages.ubuntu.com/manpages/bionic/man5/systemd.service.5.html

Creating a service can be done with the following commands on the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input sudo nano /etc/systemd/system/prometheus.service and press Enter.
    • Note: This will open a text editor within your command line.
  • Paste the text below into your command line text editor.
    • Note: Replace the 4 instances of <your-user-name> in the text content below with the username that you set up when configuring your Raspberry Pi on the first start up.
    • Note: The text content below can also be found within the prometheus.service file within this repository.
[Unit]
Description=Prometheus Server
Documentation=https://prometheus.io/docs/introduction/overview/
After=network-online.target

[Service]
User=<your-user-name>
Restart=on-failure

ExecStart=/home/<your-user-name>/prometheus/prometheus \
  --config.file=/home/<your-user-name>/prometheus/prometheus.yml \
  --storage.tsdb.path=/home/<your-user-name>/prometheus/data

[Install]
WantedBy=multi-user.target
  • After you have pasted this text into your command line text editor and replaced <your-user-name> with your actual Pi's username, you are ready to close and save the file. To do this, press CTRL + X, then Y, then ENTER.
  • On the command line, input sudo systemctl enable prometheus and press Enter.
  • Input sudo systemctl start prometheus and press Enter.
  • Input sudo systemctl status prometheus and press Enter.
    • If things were successful, after running sudo systemctl status prometheus you should see output that tells you that the prometheus services is ACTIVE.

Anytime that you make changes to ~/prometheus/prometheus.yml, you will want to restart your Prometheus service so the changes get picked up. To do this, you can run sudo systemctl restart prometheus.

Viewing the Web Interface for Prometheus

Now that the Prometheus service is running and active on your Raspberry Pi, you should be able to visit its dashboard.

Within your Pi's web browser, attempt to visit http://localhost:9090. The page should load you into the Prometheus dashboard.

Congrats! You just set up a Prometheus service to collect data. Now we need to collect data about our network and pass it into Prometheus.

Setting Up Telegraf

Telegraf Website: https://www.influxdata.com/time-series-platform/telegraf/

Github Repository: https://github.com/influxdata/telegraf

Telegraf is an InfluxDB plugin that can be used to collect any number of system metrics. We are going to use one of its many plugins to collect ping times on our network. We can use another output plugin to easily pass our collected data out to Prometheus.

Installing Telegraf

At the time of writing, the current version of Telegraf is 1.26.0. That is the version of Prometheus that I will be installing. All of the v1.26.0 downloads can be found at: https://github.com/influxdata/telegraf/releases/tag/v1.26.0.

If you are looking for a different release, all releases can be found at https://github.com/influxdata/telegraf/releases or at https://portal.influxdata.com/downloads/.

Since I installed the 64-bit ARM version of Raspberry Pi OS, I am going to install the Ubuntu & Debian versions of Telegraf. This should work with most (if not all) Raspberry Pis. You can choose to install a different version.

Telegraf has some great installation instructions (https://portal.influxdata.com/downloads/) and that is what I will be following.

Installing Telegraf can be done with a few simple commands via the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input cd ~ and press Enter.
  • Copy the commands below, paste them into your command line, and press Enter.
# influxdata-archive_compat.key GPG Fingerprint: 9D539D90D3328DC7D6C8D3B9D8FF8E1F7DF8B07E
wget -q https://repos.influxdata.com/influxdata-archive_compat.key
echo '393e8779c89ac8d958f81f942f9ad7fb82a25e133faddaf92e15b16e6ac9ce4c influxdata-archive_compat.key' | sha256sum -c && cat influxdata-archive_compat.key | gpg --dearmor | sudo tee /etc/apt/trusted.gpg.d/influxdata-archive_compat.gpg > /dev/null
echo 'deb [signed-by=/etc/apt/trusted.gpg.d/influxdata-archive_compat.gpg] https://repos.influxdata.com/debian stable main' | sudo tee /etc/apt/sources.list.d/influxdata.list
sudo apt-get update && sudo apt-get install telegraf

This process could take a few minutes to complete - depending on your internet connection.

Congrats! You've just installed Telegraf. Now we need to set a up a service for it just like we did for Prometheus.

Configuring a Telegraf Service

We want Telegraf to start up as soon as Raspberry Pi boots up. We can do this easily by creating a service for Telegraf. You can learn more about Linux Services here: https://manpages.ubuntu.com/manpages/bionic/man5/systemd.service.5.html

Creating a service can be done with the following commands on the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input sudo nano /etc/telegraf/telegraf.conf and press Enter.
    • Note: This will open a text editor within your command line.
  • Paste the text below into your command line text editor.
    • Note: The text content below can also be found within the telegraf.conf file within this repository.
    • This is where you might want to make changes. The configuration file says that we are going to ping 1.1.1.1 (Cloudflare's public DNS) 1 time every 15 seconds and our ping command will timeout after 5 seconds. We will then make the data available in a Prometheus format on port 9091.
# Input plugins

# Ping plugin
[[inputs.ping]]
urls = ["1.1.1.1"]
count = 1
ping_interval = 15.0
timeout = 5.0

# Output format plugins
[[outputs.prometheus_client]]
  listen = ":9091"
  metric_version = 2
  • After you have pasted this text into your command line text editor, you are ready to close and save the file. To do this, press CTRL + X, then Y, then ENTER.
  • On the command line, input sudo systemctl enable telegraf.service and press Enter.
  • Input sudo systemctl start telegraf.service and press Enter.
  • Input sudo systemctl status telegraf.service and press Enter.
    • If things were successful, after running sudo systemctl status telegraf.service you should see output that tells you that the telegraf services is ACTIVE.

Anytime that you make changes to /etc/telegraf/telegraf.conf, you will want to restart your Telegraf service so the changes get picked up. To do this, you can run sudo systemctl restart telegraf.service.

Congrats! You just set up a Telegraf service to collect network ping data. Now we need to tell Prometheus that there is a new set of data available for collection on port 9091.

Pointing Prometheus to Telegraf's Data

Now that we have Telegraf service running to collect our network ping times, we need to inform Prometheus about this new source of data. To do this, we need to update Prometheus's configuration file and then restart the Prometheus service to have the change picked up.

First we need to update our prometheus.yml file. This can be done via the command line:

  • Open a new command line window.
  • Input sudo nano ~/prometheus/prometheus.yml and press Enter.
  • Underneath the scrape_configs section, add the following:
    • Note: An example Prometheus configuration file can be found within the prometheus.yml file within this repository.
- job_name: "telegraf-agent"
  static_configs:
    - targets: ["localhost:9091"]
  • This tells Prometheus that it has another source of data it should scrape and that the data to scrape is found at localhost:9091. This port number should match the port that is listed under outputs.prometheus_client within your telegraf.conf file.
  • After you have added this information, you are ready to close and save the file. To do this, press CTRL + X, then Y, then ENTER.

Now that our Prometheus configuration has been updated, we need to restart our Prometheus service for the changes to be picked up. To do this, run sudo systemctl restart prometheus within the command line. To do this:

  • On the command line, input sudo systemctl restart prometheus and press Enter.
  • On your Raspberry Pi, open a web browser and visit localhost:9090/targets.
    • If things are set up correctly, you should see two targets listed: prometheus and telegraf-agent.
    • Note: The names of these targets match the job_name property within the scrape_configs section of the prometheus.yml configuration file.

Setting Up Grafana

Grafana Website: https://grafana.com

Github Repository: https://github.com/grafana/grafana

Grafana is an open-source tool that can be used to visual data from a number of different sources. We are going to use it to visualize the data that our Prometheus service is collecting from Telegraf.

Installing Grafana

Grafana has some great installation instructions (https://grafana.com/tutorials/install-grafana-on-raspberry-pi/) and that is what I will be following.

Installing Grafana can be done with a few simple commands via the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input wget -q -O - https://packages.grafana.com/gpg.key | sudo apt-key add - and press Enter.
  • Input echo "deb https://packages.grafana.com/oss/deb stable main" | sudo tee -a /etc/apt/sources.list.d/grafana.list and press Enter.
  • Input sudo apt-get update and press Enter.
  • Input sudo apt-get install -y grafana and press Enter.

The process could take a few minutes - depending on your internet connection. Grafana is now installed, but we need to create a service for it just like we did with Prometheus and Telegraf.

Configuring a Grafana Service

We want Grafana to start up as soon as Raspberry Pi boots up. We can do this easily by creating a service for Grafana. You can learn more about Linux Services here: https://manpages.ubuntu.com/manpages/bionic/man5/systemd.service.5.html

Creating a service can be done with the following commands on the command line:

  • Open a new terminal window on your Raspberry Pi.
  • Input sudo /bin/systemctl enable grafana-server and press Enter.
  • Input sudo /bin/systemctl start grafana-server and press Enter.

Viewing the Web Interface for Grafana

If everything has gone right, we should not be able to log into Grafana and start dashboarding data! On your Raspberry Pi, open a web browser and attempt to visit http://localhost:3000.

You should see the Grafana login page. You should be able to login with the following default credentials of:

username: admin
password: admin

Please, change the password when you are prompted.

If you were able to log in - we are ready to start viewing our network health data!

Adding Prometheus as a Data Source to Grafana

Now that we have Grafana to dashboard our data, we need to add our Prometheus service to Grafana as a potential data source. To do this:

  • Open a web browser on your Raspberry Pi and visit localhost:3000/.
  • Log into your Grafana instance.
  • From the left-hand sidebar menu, hover over the ⚙️ (Settings) icon and select Data sources from the flyout menu.
  • Once the page loads, click the blue Add new data source button.
  • Select the Prometheus option from the page.
    • Note: You may need to search for it on the page.
  • Enter a name for your datasource in the Name field at the top of the page.
    • If you aren't sure about a name, I would go with something simple like Prometheus.
  • Within the HTTP section enter localhost:9090 in the URL field.
    • Note: If you used a different port for your Prometheus server, use that port instead.
  • Scroll down to the bottom of the page and click the blue Save & test button.

If things are working correctly, you should see a green Data source is working expandable pop up below the blue Save & test button.

If you need more assistance or have questions, Grafana has some excellent documentation about adding a Prometheus datasource. That documentation can be found at: https://grafana.com/docs/grafana/latest/datasources/prometheus/

Creating our Dashboard & Panel in Grafana

Now that Grafana has access to the data that we are collecting about our network's health, we can finally create our network monitoring dashboard!

Grafana Dashboard

You can either make your own custom dashboard from scratch, or you can import my dashboard via the grafana-dashboard.json file that is included within this repository. Grafana has a great explanation of how to import a dashboard at: https://grafana.com/docs/grafana/latest/dashboards/manage-dashboards/#import-a-dashboard

This is not a comprehensive Grafana tutorial. Grafana is extremely powerful! If you are looking for more tutorials, Grafana has some great ones here: https://grafana.com/tutorials/. A quick Google search should also get you some great answers!

Expanding this Project

There are numerous ways that this project could be expanded or customized.

  • A Cloudflare Tunnel (https://developers.cloudflare.com/cloudflare-one/connections/connect-apps/) could be used to make your local Grafana dashboard available to the public internet in a secure manner. This would allow you to check on your network's health from anywhere in the world (as long as your Pi had a network connection).
    • Cloudflare offers this service for free. You could even buy a cheap custom domain to tunnel into your Pi!
  • Telegraf has many plugins that can be used to collect data. Those plugins can be found at https://docs.influxdata.com/telegraf/v1.26/plugins/. You could find a new plugin to use to collect another source of data.
  • You could modify the existing telegraf.conf file to ping more websites or change how frequently pings are done.
  • Make some complex visualizations in Grafana. This tutorial only scratched the surface of what is possible with Grafana. Go crazy and make some cool, dynamic panels!

Acknowledgements

About

A Raspberry Pi Grafana dashboard to monitor network health via Prometheus and Telegraf data.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published