v0.6.0

v0.6.0
Neue Funktionen/Verbesserungen bei der Laderegelung:

• Absorbtion/Float Ladespannung
• Autobalancing
• CutOff (Überarbeitet)
• Funktion "Ladesstrom reduzieren - SoC" erweitert um "Mindest Ladestrom in A" (#101)

Weitere neue Features/Verbesserungen:

• Neues BMS: Seplos V3 (#81)

• Neues Wechselrichter CAN-Protokoll: BYD Protocol (SolarEdge RWS)

• Passwortschutz für das WebUI (#93)
  Username: bsc
  Passwort: admin

• Problem beim Runden des SoC behoben (Fix 100% SOC bei Seplos) (#113)

• Kleinere Änderungen/Verbesserungen in den Menüs des WebUI (z.B. Invertermenü aufgeteilt zu bessern Übersichtlichkeit)

• Größere Änderungen im Unterbau des BSC

Wichtiger Hinweis!
Folgende Werte müssen nach dem Update kontrolliert und ggf. angepasst werden:

• Absorption Ladespannung
• Ladestrom reduzieren - SoC; Pro 1% um x A reduzieren
• Cut-Off Strom

v0.5.14

v0.5.14

• Toggeln des Triggergrundes im Log behoben; Dadurch wurde das Log unnötig vollgeschrieben

v0.5.13

• Remove WebUI v2
• Anpassungen für HW2.4.1

v0.5.13

v0.5.13

• Remove WebUI v2
• Anpassungen für HW2.4.1

v0.5.5

• Error wirh Cyclin-BMS fixed
• Added custom hostname
• Added display timeout

Supporters can activated the new WebUI.
The new WebUI is modern and responsive and has new features.
More information about the supporter in the BSC in the Supporter menu.

Important note!
Updating from version 0.3.x to >= 0.4.x cannot be done over the air. It must be flashed over the serial port because the partition table has changed.

v0.5.4

• Some bug fixes
• Added support for Gobel BMS PC200 (Test)
• Added support multiple RN150 BMS (Test)
• Added discharge controll by cell voltage

Supporters can activated the new WebUI.
The new WebUI is modern and responsive and has new features.
More information about the supporter in the BSC in the Supporter menu.

Important note!
Updating from version 0.3.x to >= 0.4.x cannot be done over the air. It must be flashed over the serial port because the partition table has changed.

v0.5.0

• Some bug fixes

• New Feature: Cellvoltage plausibility check; This can be used to monitor whether the cell voltages change regularly or whether they are fixed at one value.

• New Feautre: Trigger by SoC

• Restapi extended by the inverter values

• For supporters there is a new WebUI that can be activated. More information about the supporter in the BSC in the Supporter menu
  The new WebUI is modern and responsive and has new features.

Important note!
Updating from version 0.3.x to >= 0.4.x cannot be done over the air. It must be flashed over the serial port because the partition table has changed.

v0.4.16

Added Sylcin-BMS support

Added BMS temperatures to alarmrules
Added BMS data (serial 0-2) to the dashboard (#33)
Added several small features

Fix CAN-Bus problems with the DEYE inverter
Various bug fixes


Important note!
Updating from version 0.3.x to >= 0.4.x cannot be done over the air. It must be flashed over the serial port because the partition table has changed.

v0.4.12

Important note!
Updating from version 0.3.x to >= 0.4.x cannot be done over the air. It must be flashed over the serial port because the partition table has changed.

New features:

• Read and write NEEY settings
• Support for the DALY BMS
• 8 additional serial ports in combination with serial extension
• Charge control via CAN bus reworked/extended
• And much more ...

Several bug fixes

v0.3.1

This version contains only bug fixes.

• Transmit error in CAN-Lib
• JK-BMS current value

v0.3.0

• Bluetooth/Wifi connection and stability problems fixed
• Bluetooth extended from 5 to 7 connections
• Some minor optimizations

New device:

• SEPLOS-BMS (RS485)