This tool was developed for a Western-digital 250GB HAWK family drive (e.g. WD2500KS-??MJ??, WD2500KS-??MK? .....). It uses the unallocated reserved-areas mapped to heads 2 through 5 to store and access data.
use 'lspci -v' to find your SATA IO address, e.g:
00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology Device b002 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 *** I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] *** I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at f000 [size=16] Capabilities: [70] Power Management version 2 Kernel driver in use: ata_piix
Known issues with the tool:
- The tool is desinged to work on the master drive of the specific IO port.
- The code does not detect bad-sectors in the service area. If such sectors exist, the code will behave unexpectedly.
- While the tool is sending Vendor Specific Commands the OS might report errors trying to communicate with the drive. In fact, it may be required to reboot the OS (or power-cycle the drive) after the tool had completed executing.
- When reading the service-area into a file, the tool reads the entire area (mapped to heads 2 through 5) regardless of the size of the file written to the service-area.
We believe the OS/hard-drive hanging issue can be resolved by using the SGIO library.
to compile, use: gcc -Wall -O -g -o osslab-SA osslab-SA.c
to read ID information from the drive, use: osslab-SA -p 0xport to write to reserved area, use: osslab-SA -p 0xport -w filename to read from reserved area, use: osslab-SA -p 0xport -r filename
IMPORTANT: The code can render your data and hard-drive corrupted or otherwise inaccessible, use at your own risk!
This code was rewrited www.recover.co.il's source code. You can do below command as test:
-
-s : Service area sectors-per-track ex: ./osslab-SA -p 0xf0f0 -s 720
-
-d : Num of heads ex: ./osslab-SA -p 0xf0f0 -d 6
-
-t : Service area tracks ex: ./osslab-SA -p 0xf0f0 -t 64
-
-k : reading head num ex: ./osslab-SA -p 0xf0f0 -r test.bin -k 0
Of course, you can do ./osslab-SA -p 0xf0f0 -r test.bin -s 720 -d 6 -t 64 -k 0
前言此
此程式主要針對 WD 250GB HAWK 家族的硬碟 (e.g. WD2500KS-??MJ??, WD2500KS-??MK? .....)
主要使用沒有被宣告的保留區域,並使用磁頭2磁頭5來讀寫資料,再經過全盤寫0,保留區資料還是在的,(磁頭12為硬體工作軔體區請勿動到)。
請使用 “lspci -v”指令來找到你的SATA IO位置, 如下所示
00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology Device b002 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 *** I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] *** I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at f000 [size=16] Capabilities: [70] Power Management version 2 Kernel driver in use: ata_piix
請自行測試出硬碟的Port位置 編譯：gcc -Wall -O -g -o osslab-SA osslab-SA.c 讀取硬碟的ID資訊：osslab-SA -p 0xport 寫資料到硬碟保留區：osslab-SA -p 0xport -w filename 從硬碟保留區讀出資料：osslab-SA -p 0xport -r filename
注意：此程式會造成你的資料或硬碟損毀或其他無法回復的問題，請在你可接受的風險內使用
本程式改寫自www.recover.co.il, 並加入底下參數使用者可在一開始時自行輸入:
-
-s : Service area sectors-per-track 例：./osslab-SA -p 0xf0f0 -s 720
-
-d : Num of heads 例：./osslab-SA -p 0xf0f0 -d 6
-
-t : Service area tracks 例：./osslab-SA -p 0xf0f0 -t 64
-
-k : reading head num 例：./osslab-SA -p 0xf0f0 -r test.bin -k 0
當然你也可以使用 ./osslab-SA -p 0xf0f0 -r test.bin -s 720 -d 6 -t 64 -k 0