Skip to content

Tools for building gnubee firmware - and maybe more.

License

Notifications You must be signed in to change notification settings

vincele/gnubee-tools

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

GNUBEE Tools

This package contains tools specifically for working with the GnuBee NAS platform - See www.gnubee.org.

Currently the primary focus is building a firmware image to boot into the Linux kernel.

A normal boot requires that a root filesystem already exists; this can be on an SD card, USB storage, or SATA device (including md-raid or LVM2). This filesystem must be named "GNUBEE-ROOT" and findfs must be able to find it. The default config builds support for xfs, ext4, and btrfs.

This package contains config files and scripts to build a kernel and an initramfs, in a format that can be written to flash.

If GNUBEE-ROOT cannot be found, the initramfs drops into a shell. Enough tools are available to configure the network, create md arrays, format an ext4 filesystem, and install Debian over the network. A script called "config" is available which does much of this for you. It will not create md arrays, but if you create one manually, it will find it and offer to install to it.

At the initramfs shell, you can "cat config" to see the script or just type "config" to run it.

Preparation

To build the firmware, you will need (something approximating) a MIPSEL Debian root filesustem. Various tools for the initramfs are simply copied from this file system rather than being built separately: lazy, but fast. This can be achieved by one of:

1/ doing the full build on the GnuBee

2/ setting up "ssh" access to the GnuBee, and providing the address in GNUBEE_SSH_HOST in the config file

3/ Running "gbmake chroot" to create a local Debian filesystem using "debootstrap". This can be run on any Linux distro (tested on openSUSE).

If you are using a GnuBee you will need various packages installed. To install them run:

sudo apt-get install make gcc flex bison busybox

On whichever machine you want to build the kernel (which could be a GnuBee) you will need:

sudo apt-get install git make gcc bc libssl-dev u-boot-tools unzip rsync

Other packages for the GnuBee that are optional but give more functionality in the initramfs are:

sudo apt-get install mdadm dropbear cryptsetup-bin \
	mtd-utils u-boot-tools xfsprogs btrfs-progs lvm2 evtest

If you want to build firmware that can be used to install Debian, you also need

sudo apt-get install debootstrap

All of these are installed when using "gbmake chroot"

Building

To build a firmware image you can

git clone https://github.com/neilbrown/gnubee-tools.git
git clone --depth=20 https://github.com/neilbrown/linux.git -b gnubee/v6.1
cd linux
../gnubee-tools/scripts/gbmake firmware gbpc1-6.1

If you run this on the GnuBee itself (with Debian installed), you need to ensure some swap space is configured, as "lzma" needs to allocate a lot of memory to compress the initramfs - 2Gig seems to be enough. No other configuration is needed.

If you run it on another machine, you will need ssh access to the GnuBee. This needs to be configured in gnubee-tools/config, which can be copied from config.sample. In particular, CROSS_COMPILE and GNUBEE_SSH_HOST must be set.

The above command will build firmware for a GnuBee PC1. If you have a PC2, specify "gbpc2-5.15" on the "gbmake firmware" command.

I find that the gbmake step takes 3 3/4 hours on a GnuBee, and a little over 6 minutes on my octo-core 32GB RAM desktop. The git clone of Linux takes roughly forever on the GnuBee due to limited memory, unless the "--depth" option is specified as above. Alternately, use

wget  https://github.com/neilbrown/linux/archive/gnubee/v6.1.zip
unzip v6.1.zip
cd linux-gnubee-v6.1
../gnubee-tools/scripts/gbmake firmware gbpc1-6.1

If you want to just run gbmake firmware without the full path, you can ln -s the script to a bin directory. Don't copy it as it won't work like that.

Installing

The image created is placed in gnubee-tools/build/gnubee-<version>-<variant>.bin.

If you have this on the GnuBee and have mtd-utils installed, you can flash it with flashcp -v gnubee-5.15-gbpc2.bin /dev/mtd3. Alternatively you can copy it to a VFAT filesystem on USB storage (do not forget to rename it to gnubee.bin), and boot with that storage plugged in. This will cause the firmware to be copied to flash. When one LED stops flashing and both LEDs are solid-on, remove the USB storage and reboot into the new firmware.

First Boot

The firmware image is quite large, partly because it contains all modules - that seems the easiest way to distribute them. On first boot you will find /lib/modules is a tmpfs filesystem containing all the modules, and so wasting some of your precious memory. If you run /lib/modules/keep, the modules will be copied into your root filesystem. Subsequent boots will not have /lib/modules mounted. Note that this isn't needed if you use "config" to create your debian install - that will copy the modules in for you.

Install / Rescue mode

If the firmware fails to find a filesystem with the label GNUBEE-ROOT, it will run a shell on the serial console from which you can repair or create such a filesystem. If you don't have a serial cable, this isn't much help.

If you hold the small black button during boot, the firmware will notice and will not even look for GNUBEE-ROOT but will start a shell and, importantly, configure the network and start the "dropbear" ssh daemon. Note that if you press the button too early, the u-boot loader will notice and decide to try to load something from the network. You need to wait about 10 seconds.

The first network port (black) is by default configured with address 192.168.10.1. The second (blue) port is configured to use DHCP to request an address. You can use whichever of these is more convenient. To login you will need to know the root password, which is "GnuBee".

You can over-ride some defaults by creating a VFAT filesystem on a USB storage device and placing a file gnubee-config.txt in the root directory. Then plugging this device in during boot. The file should contains "name=value" assignments, one per line. Following names are meaningful.

  • CONFIGURE_NET=yes - this is equivalent to holding the black button during boot

  • CONFIGURE_BLACK_IP=xx.xx.xx.xx - If the network is being configured, either due to the button being pressed or due to CONFIGURE_NET, the Black network port is configured to the given IP address, and the DHCP server is not run.

  • CONSOLE_SHELL=yes - this is equivalent to not finding GNUBEE-ROOT; a console shell is run, but the network is not configured.

Once you are logged in you can modify the network configuration (if, for example, you want some other static IP, or need to specify a gateway address) and can create any RAID arrays you want etc. You can install Debian at this point using debootstrap.

Much of the work for configuring and installing Debian can be performed using a script called config. Simply run config and answer the questions. You will soon have a minimal Debian installation that you can boot into. From there you can install anything else that you want.

Cross Compiling

If you want to compile the kernel on some other computer, you will likely need a cross compiler. These are available from various places, such as described in https://wiki.debian.org/CrossToolchains. If you want to compile your own (as I did), here are some steps.

  • Install gmp mpfr mpc devel packages

      sudo apt-get install libgmp-dev libmpfr-dev libmpc-dev
    
  • collect the source code:

      cd /home/git
      git clone git://sourceware.org/git/binutils-gdb.git
      git clone git://gcc.gnu.org/git/gcc.git
    
  • build a recent released version of binutils (I'm using 2.29.1)

      cd binutils-gdb
      git checkout binutils-2_29_1
      mkdir MIPS
      cd MIPS
      ../configure --target=mipsel-unknown-linux-gnu --prefix=/opt/cross
      make
      sudo make install
    
  • build a released gcc (e.g. 7.2.0)

      cd ../../gcc
      git checkout gcc-7_2_0-release
      mkdir MIPS
      cd MIPS
      ../configure --target=mipsel-unknown-linux-gnu --prefix=/opt/cross \
        --enable-languages=c --without-headers \
        --with-gnu-ld --with-gnu-as \
        --disable-shared --disable-threads \
        --disable-libmudflap --disable-libgomp \
        --disable-libssp --disable-libquadmath \
        --disable-libatomic
      make -j
      sudo make install
    
  • Now use /opt/cross/bin/mipsel-unknown-linux-gnu- as the CROSS_COMPILE setting in your config file.

About

Tools for building gnubee firmware - and maybe more.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Roff 94.7%
  • Shell 3.9%
  • C 1.4%