General notes:

Dump an image:

bootstrap

dump_image 0xFFFF0000.bin 0xFFFF0000 0x00002000

stack dump_image 0x4006000.bin 0x4006000 0x00010000

Display bytes:

mdw 0xFFFF0000 0x50

3.3v + 4.7k ohm = 0x1C00A846

CON1 pins

(I apologize, the colors here are colors for wires I have soldered, heh)

88i6745 to CON1 to 0x1C00A846 io port value to bitflip to high/low

Test Wire	CON1 pin	0x1C00A846 value	bit flipped	LSR#13	LSR#9	status	88i6745 pin	fw function
normal	XX	0xc802	1100100000000010	110	1100100	normal H/L	lots
---------	---------	-----------------	----------------	----------------	-------	-------------	--------	------------
yellow	28	0xc800	0000000000000010	000	0000000	HIGH	43
green	26	0xc806	0000000000000100	000	0000000	low	44
blue	24	0xc80a	0000000000001000	000	0000000	low	46
violet	22	0xc812	0000000000010000	000	0000000	low	48
black	20	0xc822	0000000000100000	000	0000000	low	49
brown	18	0xc842	0000000001000000	000	0000000	low	50
red	16	0xc882	0000000010000000	000	0000000	low	51
yellow	06	0xc902	0000000100000000	000	0000000	low	52
orange	32	0xca02	0000001000000000	000	0000001	low	41	LSR#9
black	38	0xcc02	0000010000000000	000	0000010	low	37	LSR#9
brown	36	0xc002	0000100000000000	000	0000100	HIGH	38	LSR#9
red	34	0xd802	0001000000000000	000	0001000	low	40 - to 3.3v
n/a	n/a	0xe802	0010000000000000	001	0010000	low	104 - P13 to 3.3v - R72 to 3.3v
n/a	n/a	0x8802	0100000000000000	010	0100000	HIGH	106 - P14 to ground	high = skip RAM test ?
n/a	n/a	0x4802	1000000000000000	100	1000000	HIGH	107 - P15 to ground	run RAM test

Notes from Doomer, hddguru forums

http://forum.hddguru.com/viewtopic.php?t=20324&f=13&start=20#p136913

"E62" from (2061-701499-e00) to GND makes 0x8000 -> inversed bit 0x16 (actually bit 16) of port 0x1C00A846 - so this is P15, 6745 pin 107 "E61" from (2061-701499-e00) to GND makes 0x4000 -> inversed bit 0x15 (actually bit 15) of port 0x1C00A846 - so this is P14, 6745 pin 106

Ram test = 0xFFFF01BC, triggered by (P15 HIGH = 88i6745 107 HIGH), so ram test is done by default.

normal value for 0x1C00A84E = 0x00f0 = 0000000011110000

88i6745 to CON1 to 0x1C00A84E io port value to bitflip to high/low

Test Wire	CON1 pin	factory jumpbers	0x1C00A84E value	bit flipped	status	88i6745 pin	fw function
normal	XX		0x00f0	0000000011110000	normal	lots
TP E6	??	??	0x02f0	0000001000000000	?	109	enable external flash?
white	30		0x00b0	0000000001000000	normally HIGH	42
PUIS	XX	3+4	0x0050	0000000010100000	normally HIGH
	XX	5+6	0x00a0	0000000001010000	normally HIGH		1.5G PHY
	XX	3+1	0x00e0	0000000000010000	normally HIGH
?	??	??	0x2000	0010000000000000	?	?	immediate jump to serial console

Factory Jumpers

Jumper Pin	6745 pin	CON1 pin
1	42	30
2
3	117	XX - serial
4	GND	GND
5	118	XX - serial
6	GND	GND
7	43	28 via resistor

Normal values for IO ports read from

Port	Value	Bits	Name
0x1C00A84E	00f0	0000000011110000	CONFIG_IO_A
0x1C00A846	c802	1100100000000010	CONFIG_IO_B

JTAG to mini console via OpenOCD

E.g., to make sure you've got 3.3v ttl serial connected up correctly.

Speed: 115200 N,8,1

reset halt reg sp_usr 0x4005000 reg pc 0xffff01b4 resume

Test Points that are GND

e22 e12 unlabeled TP reverse C shape at E37

Test Points that are 3v3

one side of R3 on E5

Test Points that are 1.34v

E97

Normal values for IO ports written to

| | | | | 0x1C002806 | 007f | 0000000001111111 | | 0x1C004AA0 | 0000 | 0000000000000000 | | 0x1C00A20A | 0200 | 0000001000000000 | | 0x1C00A20C | 0000 | 0000000000000000 | | 0x1C00A800 | ffc4 | 1111111111000100 | | 0x1C00A820 | 666e | 0110011001101110 | | 0x1C00AA00 | 0004 | 0000000000000100 |

Tricks:

0xFFFF0088 - short P14 to ground (normally high)

0xFFFF00xx, A0 A8, B0, B8 - top 3 bits of 0x1C00A846 are 100, 101, 011, or 111 - jump to console. Normally 110.
 - 111 = infinite loop?

Problems:

P13 to 3.3v - does something that makes openocd `reset halt` not halt immediately in ROM, no idea why.


### 6745 pins
| pin | note |
| --- | ---- |
| 01 | TP P3 to DNP resistor to ground - black |
| 02 | TP P4 to DNP resistor to ground - green |
| 03 | 3.3v net on pcb top |
| 04 | via to unmarked TP on bottom, jumper resistor to blind VIA - to cap buffered (C13) GND - suspicious |
| 05 | DNP cap to via to ground |
| 06 | TP P5 - violet |
| 07 | TP P6 - blue |
| 08 | GND |
| 09 | 3.3v net on pcb top |
| 10 | 3.3v net on pcb top |
| 11 | GND |
| 12 | pickup |
| 13 | pickup |
| 14 | GND |
| 15 | resistor to ground to unmarked TP on bottom - suspicious |
| 16 | via to GND |
| 17 | pickup |
| 18 | pickup |
| 19 | 0ohm resistor to 3.3v via to unmakred TP on bottom - suspicious |
| 20 | 0ohm resistor to 3.3v via to unmakred TP on bottom - suspicious |
| 21 | pickup |
| 22 | pickup |
| 23 | cap to GND |
| 24 | pickup |
| 25 | pickup |
| 26 | pickup |
| 27 | pickup |
| 28 | 3.3v net on pcb top |
| 29 | via to unmarked TP on bottom - suspicious |
| 30 | JTAG |
| 31 | SMOOTH motor |

| 42 | Factory Jumper 1 |
| 109 | Test Point E6 - normally low, set high causes JTAG problems |


32 - SMOOTH motor 
33 - SMOOTH motor ?
34 - SMOOTH motor ?
35 - via to unlabeled test point
36 - cap to ground + via to unlabeled test point