Change Log

Happy Hare - Detailed Revision History

Imperfect Log Changes since V2 launch

v2.0.1

• Initial Release (forked from my ERCF-Software-V3 project which is now deprecated).
• HHv2 is a rewrite to structure the software so it can support all types of MMU (only ERCF at release) and sanitize command set
• Adds total control of motor synchronization, multiple endstops (even for the extruder!!)
• Although HHv1 (aka ERCF-Software-V3) will remain available, HHv2 will be where all future enhancements will be made
• The latest KlipperScreen-Happy_Hare edition requires HHv2 (for my sanity)
• Much better doc and LOTS of new features to discover

v2.1.0

• Speed and extrusion overrides (M220/M221) support .. records overrides across tool changes (MMU_TOOL_OVERRIDES command to see/reset)
• SpoolMan support (new options to MMU_GATE_MAP for SpoolD.. see doc)
• Separate "per-print" and total swap stats! No need to clear in your print_start anymore.
• "Auto restoring" gate quality indication (the "excellent/good/../terrible" one). Slowly averages out bad results.
• New "state machine" that closes a lot of annoying corner cases that I knew about but most users hadn't found yet doc.
• New filament cutter option (Alternative _MMU_CUT_TIP macro) instead of tip forming and mmu_form_tip_macro setting
• MMU_UNLOCK is back (but as an optional step to resume temps). Can just call RESUME as well.
• Better support for Octoprint users where the [print_stats] module is not available. Read up on new state machine and _MMU_START_PRINT and _MMU_END_PRINT conventions (must read doc)
• New moonraker gcode pre-processor module! Adds !referenced_tools! placeholder so you can automatically check all used tools before printing wiki
• 'MMU_FORM_TIP' command updated to allow for runtime "tuning" Any variable to the macro can be adjust (and persisted) for testing or tweaking in print (handles tip cutting macro as well)
• Config now also automatically adjusts references to "extruder" when referring to stepper (e.g. in rare [controller_fan], [homing_heaters] and [angle])
• Lots of little things/bug fixes but I lost track 🫣

v2.2.0

• Replacement of manual steppers with new MMU toolhead - faster homing and movements in general, new optional gate and extruder sensors, optional encoder, intial support for Tradrack and other customized designs.
• Ever wanted to use Happy Hare on a non-ERCF MMU?
• Ever wanted to use a pre-extruder entry sensor instead of collision?
• Wanted to fit a gate sensor and not rely on encoder for loading and parking at the gate
• Want to run without an encoder? (why? 🤷 )
• Want fast (no wait) homing?
• DON'T WANT TO RECONFIGURE YOUR EXISTING EXTRUDER? 👍
• Want the latest and greatest features?

v2.3.0

NOTE: Requires Klipper 0.12.0 or greater

• LED support for bling, gate_status, filament color and action status, pre-gate sensor support for automated loading and gate_status setting, BTT MMB board support, integrated filametrix cutter support, new [mmu_sensors] config section of easy sensor setup. Doc improvements. New Features:
• LED (bling) support! See new page in the wiki doc
• Pre-gate sensor support: Automatically set gate_status, LED status and activate pre-load. Oh, and new earlier run-out detection of reliable EndlessSpool
• Installer updates and support for BTT MMB board
• Integrated Filament Cutter support (Filametrix)
• Improved doc. E.g. Conceptual MMU
• New [mmu_sensors] section for simple setup of filament_sensors and endstops
• Enhancements for gate_sensor as alternative or in addition to encoder
• Lots of bug fixes and minor enhancements requested.
• Version tracking and better feedback on what to do
• Enhancements to existing commands. E.g try: 'MMU_STATUS SHOWCONFIG=1'

v2.3.1

• Better Spoolman integration: will now pull material and colors from spoolman in addition to activating the spool
• Allow the LED effects to be configure anywhere on a chain (as well as gate 0->N or N->0 ordering)
• EndlessSpool got some love because I think it will be much more valuable with pre-gate switches and early runout detection:
• a) endless_spool_on_load parameter that will activate ES on loading a tool with empty gate
• b) endless_spool_final_eject distance specification for push beyond park position in an attempt to prevent filament from being accidentally re-loaded
• c) Cleanup of the display on klipper console and log messages
• d) Will ensure that the gate_status is at least "unknown" when MMU_REMAP_TTG is run, so attempt will always be made to load from the gate

v2.4.0

• Updated LED support with lots more "multi-segment" flexibility
• New servo calibration - to fine tune and save without klipper restart!
• New full set of default toolhead positioning macros (defined in mmu_sequence.cfg)
• Full support for pre-extruder sensor option (prior to extruder entry)
• Exposed vendor-specific params (including the "cad_" set -- see doc at bottom of mmu_parameters.cfg)
• Full support for Tradrack including installer
• New manual bowden calibration for setups without encoder
• Workaround for CANbus comms timeout that is plaguing klipper
• Much improved MMU_STATUS SHOWCONFIG=1. It will tell you in english what loading and unload sequence you have based on dynamic changes with MMU_TEST_CONFIG or sensor disable/enable.
• EndlessSpool is now available on tool load
• Sync feedback sensor support .. I.e support for Annex Belay or another other sensor including proportional feedback. doc
• Improved "tip forming" test procedure and MMU_FORM_TIP command
• Fixed silly bug in spoolman integration where spool_id was being used to search as filament_id
• New toolhead_ooze_reduction parameter for tuning without messing with what should be fixed extruder measurements. Doc page to follow
• Refined toolhead unloading with better detection of incorrect config
• Cleanup and separation of config files based on function
• Lots of new/updated doc

v2.4.1

• Fixes / update to the way toolhead movement occurs through the "sequence macros" like _MMU_PRE_UNLOAD and _MMU_POST_LOAD etc.
  • Also if enabled these will now work while not actively printing (that was an oversight)
  • These macros also play nicely with Klippain pause/resume macros now
  • The z_hop_height_error has been deprecated. Additional z_hop height can be configured in the macro variables at the start of mmu_sequence.cfg
• LED update
  • Better error feedback on LED misconfiguration
  • Fix for led index when order of reversed.

v2.4.2 (Klipperscreen-Happy Hare edition will also need to be updated)

• New placeholder preprocessing for colors and filament temps pulled from you slicer ( !colors! and !temperatures! ). See here
• LED update: New effect custom_color. This will display colors stored for each gate based on user setting. One example use is to render the colors used in the slicer so you can visually compare with what is loaded. Documentation is in the gcode pre-processing section.
• Improved movement "sequence" macros. These now work better when not completely homed (e.g. z-hop is optional.
• CUT_TIP macro now has option to control whether movement goes back to wipetower or not after cut
• Faster pausing on runout
• Fix for not automatically engaging the sync/servo after fixing error and resuming.
  • New Slicer Setup doc on how to setup your slicer to disable tip forming
  • New Toolchange Movement doc on how to setup toolhead movement during toolchange or error
• Couple of new states to filament movement. These are to enable and display of various other sensors such as a gate sensor (option to encoder) and pre-entry extruder sensor.
• New rendering of filament position in console (and KlipperScreen-HH) showing all sensor options if fitted
• Imporved use of miscellaneous sensors to detect errors or non-errors
• Cleanup of the status displays of various commands MMU_GATE_MAP, MMU_TTG_MAP, MMU_ENDLESS_SPOOL
• New encoder calibration routine that allows calibration that "remembers" gate homing point and compensates for space between gate sensor and encoder if both are fitted
• Other bug fixes report in github "Issues"

v2.4.3

• Bug fixes reported via github "Issues"
• Added capability to install to auto-check github to ensure the latest version and to switch branches with -b <branch name> option

v2.5.0 (Recommend Klipperscreen-Happy Hare edition should be updated to get dialog popup fixes)

This release centralizes macro configuration and extends will a lot more pre-packaged options

• Macro config moved into a unified mmu_macro_vars.cfg.
• Default macros have become read-only with a formal way to add custom extensions
• New recommended "print_start" and end integration
  • See https://github.com/moggieuk/Happy-Hare/wiki/Slicer-Setup
• New MMU_SLICER_TOOLS_MAP command that is used by the "print_start" and for easy integration of non-wipetower purge options like the excellent "Blobifier" E.g.

> MMU_SLICER_TOOL_MAP DETAIL=1
--------- Slicer MMU Tool Summary ---------
2 color print (Purge volume map loaded)
T0 (Gate 0, ASA, ff0000, 245°C)
T1 (Gate 1, ABS+, 00fe02, 240°C)
T6 (Gate 6, ABS, 0310fe, 240°C)
Initial Tool: T0
-------------------------------------------
Purge Volume Map:
To -> T0   T1   T2   T3   T4   T5   T6   T7   T8
T0    -   200  210  210  200  200  200  210  210
T1   200   -   210  210  200  200  200  210  210
T2   210  210   -   220  210  210  210  220  220
T3   210  210  220   -   210  210  210  220  220
T4   200  200  210  210   -   200  200  210  210
T5   200  200  210  210  200   -   200  210  210
T6   200  200  210  210  200  200   -   210  210
T7   210  210  220  220  210  210  210   -   220
T8   210  210  220  220  210  210  210  220   -

• New Tip Forming and Purging doc
• New printer variables:
  • printer.mmu.slicer_tool_map.initial_tool
  • printer.mmu.slicer_tool_map.tools.<tool_num>.material|color|temp
  • printer.mmu.slicer_tool_map.purge_volumes
  • printer.mmu.runout which is true during runout toolchange
  • printer.mmu.active_gate map of a attributes of current filament (like color, material, temp,..)
• Z-hop modfications:
  • By default HH will not return to pre-toolchange position (will only restore z-height).
  • New variable_restore_xy_pos: True|False to control sequence macros return to starting pos or let the slicer do it. This has benefit when printing without a wipe tower so the print is not contaminated at the point of tool-change
• New "addons" folder for recommended third-party extensions with ready-to-use configs
  • Includes @kevinakasam's "EREC" filament cutter logic for cutting at the MMU (ERCF specific)
  • Includes @dendrowen's excellent "Blobifier" - intelligent purging that doesn't require a wipe tower!! (Any MMU)
• Enhanced MMU_SENSORS command for quick review of all mmu sensors
• New (optional) popup dialog option in Mainsail/KlipperScreen/Fluidd when MMU pauses on error
• Two new pre-processing placeholders: !materials! and !purge_volumes!
• Also, thanks to the Blobifer author, @dendrowen, the "MMU Statistics" has been given some love with new layout and some new customization. For both total stats and current job status. See console_stat_* options in mmu_parameters.cfg). Note advanced formatting on Python3 only.

MMU Statistics:
+------------+-----------------------+--------------------------+----------+
| 1895(1230) |       unloading       |         loading          | complete |
|   swaps    | pre  |    -    | post | pre  |    -    |   post  |   swap   |
+------------+------+---------+------+------+---------+---------+----------+
|     total  | 0:47 | 6:54:24 | 0:02 | 0:02 | 5:35:31 | 6:40:30 | 20:05:52 |
|      └ avg | 0:00 |    0:13 | 0:00 | 0:00 |    0:10 |    0:12 |     0:35 |
|  this job  | 0:36 | 4:26:51 | 0:01 | 0:01 | 3:34:34 | 4:34:54 | 13:22:01 |
|      └ avg | 0:00 |    0:12 | 0:00 | 0:00 |    0:10 |    0:13 |     0:38 |
|       last | 0:00 |    0:12 | 0:00 | 0:00 |    0:10 |    0:17 |     0:42 |
+------------+------+---------+------+------+---------+---------+----------+

11:43:27 spent paused over 10 pauses (All time)
8:15:38 spent paused over 3 pauses (This job)
Number of swaps since last incident: 105 (Record: 1111)

Gate Statistics:
#0: 😎, #1: 😎, #2: —, #3: —, #4: —, #5: —, #6: 😎, #7: —, #8: —

v2.5.1

The release provides more flexibilty in tool change movement, introduces consumption counters, optimizes statistics output

• New (moonraker) pre-processing option to lookahead for next print location to allow for option to move to the NEXT print position on completion of tool change. Requires addition to [mmu_server] section of moonraker.conf:
  • enable_toolchange_next_pos: True
• variable_restore_xy_pos can now be "none", "last" or "next" (next being new functionality)
• Augmented MMU_STATS functionality to provide "consumption counters" that can warn or even pause your print when threshold is exceeded
• New doc page to explain statistics and consumption counters
• New doc page to explain spoolman config and use
• Elimination of "h" option to ERCFv2 MMU - ThumperBlock are not a compatible 23mm wide so no longer required
• More accurate timing of tool change phases
• Defaults for "white" and "black" filament can not be configured in mmu_macro_vars.cfg
• Fixes to printer.mmu.runout and printer.mmu.last_tool for better accuracy at all possible times
• Filament remaining in toolhead is now tracked accross reboots / restarts to prevent over extruding initial load
• custom_color is now a more intuitive slicer_color and set with the MMU_SLICER_TOOL_MAP command (MMU_START_SETUP does this for you)
• New config parameter extruder_temp_variance to specify the +/- delta allowable when waiting for extruder temperature
• Updates and to bloblifier macro (needs latest klipper)
• Allow specifying spool_id in advance for supporting RFID readers. You can read more about it here

v2.5.1 (patches)

• Fixed incorrect doc in mmu_macro_vars
• Bug: Fixed user defined load/unload_sequence macro names (previously would always look for default names)
• Add all slicer tools to the "slicer_tool_map" (unused tools only visible with DETAIL=1 flag).
• Set color on Tx macros so color can be seen in Mainsail / Fluidd UI's. Requires refresh of Mainsail screen because it doesn't update dynamically :-(

v2.5.2

• Doc converted to Wiki and removed from distribution. Old doc links will be invalid

v2.6.0

Main focus on this release is the reduction of blobing, stringing and tuning for beautiful prints Read here. Most issues are because of incorrect toolhead parameters and the former lack of a retract setting when the toolhead is moving. Both of those are now solved with automated toolhead calibration (including tip cutting variables) and an new z-hop ramp setting:

• Added new MMU_CALIBRATE_TOOLHEAD command for automated measurement of toolhead_extruder_to_nozzle, toolhead_sensor_to_nozzle, toolhead_entry_to_extruder and toolhead_ooze_reduction. Read the doc but this will eliminate incorrect "trial and error" values for these key dimensions.
• Added new toolchange_retract and toolchange_retract_speed parameters to allow for retraction at the time of "z-hop" and un-retract as print resumes.
• Added new z_hop_ramp parameter to control how the toolhead move off the print to help break stringing. It allow the definition of a horizonal move on top of the "z-hop". The direction will be towards the center of the print area. The toolhead will ramp up and away from the print and then move back to original position above starting point. z_hop_speed should be increased closer to your x,y travel speed
• Updated form_tip and cut_tip macros (and Blobifer) to correctly compensate for toolhead_ooze_reduction and toolchange_retract
• Blobifier automatically calculates "additional purge" volume basaed on filament left in the hotend based on calibration rather than having to compensate by altering slicer purge map
• New printer.mmu variables.. 'extruder_filament_remaining', 'extruder_residual_filament', 'toolchange_retract' for use in your own macros
• Removed some minor pauses when resuming print
• New MMU_COLD_PULL helper command. Useful in its own right but essential for the new toolhead calibration. Check it out - it can work in a completely automated way (https://github.com/moggieuk/Happy-Hare/wiki/Blobbing-and-Stringing#---cleaning-extruder-with-a-cold-pull)

Other new features include:

• Help address one of the Timer Too Close error conditions - Klipper has a less than optimal "save-variable" implementation can can cause problems with old/slower SD-cards. To workaround this HH now includes a batch update so all the HH overhead is combined into one or two calls rather than the previous 10 or so. You can see a "mmu__revision" added to you mmu_vars.cfg that increments on every write.
• Couple more bug fixes (erroneous load errors) when using the EXTRUDER_ONLY=1 flag on extruder loading/unloading without using bypass
• Added gate_autoload parameter to allow the pre-gate sensor autoload feature to be disabled
• Enhanced EndlessSpool functionality with endless_spool_eject_gate option allow for one gate to marked the waste gate ('W' in status) so that filament fragments will be sent to this gate rather than current gate. Allows for a "dump shoot" and prevents possible tangling when buffering on certain buffer designs where retracted filament end can escape into neighboring buffers. The default value of -1 will use the current gate.
• Change parameter name extruder_homing_current to extruder_collision_homing_current to be more precise on meaning (upgrade will have made this change for you)
• Improved MMU_STATUS SHOWCONFIG=1 functionality
• New installer support:
  • For new MMU's boards
  • For GDW DS041MG servo option with Siboor ERCFv2 kits
• New servo_always_active parameter for servos that require continuous PWM signal (like GDW DS041MG). Use with caution!
• MMU_CHECK_GATE now defaults to current gate when invoked with no arguments. ALL=1 flag to force checking all gates.
• New Wiki content and enhancements to existing pages
• Bug fixes: one condition that could result in klipper "stepcompress" error

v2.7.0

Main focus: tighter integration with spoolman

• Better integration with spoolman db. Printer name and gate assignment will be reflected in the spoolman db (requires spoolman >= 0.18.1)
• Now three modes of spoolman integration: readonly the former mode, push the former augmented with the updating of assigned gate directly in spoolman, and pull where the gate map is defined by what is in spoolman. Useful in larger print farms. This is controlled via a new spoolman_support parameter. Details here
• New MMU_SPOOLMAN command for performing gate related management (updates) to spoolman db
• New innovative automatic TTG mapping strategies. Controlled by variable_automap_strategy. Essentially this is applied after reading the slicer tool map to ensure mapping to the correct gate even if the MMU is loaded incorrectly. Strategies include: 'none', 'filament_name', 'material', 'color', 'closest_color', 'spool_id'. Details here
• Moonraker plugin now parses the filament names and includes in slicer tool map and mmu gate maps
• Mainsail integration: Extruder/Filament colors and other filament attributes from spoolman are displayed in UI. Also there are controls on what color to display: slicer, gatemap (hiding unused filaments), allgates for the full gate map. Controlled with the new t_macro_color parameter. Details here 🆒

Other features/updates:

• Can now use LEDs without led_effects being installed. A new variable_led_animation_enable has been added to control this behavior and will simply be forced to False if led_effects module isn't installed. It can also be controlled from MMU_LED ANIMATION=[0|1]. LED updates have also been made slightly more efficient. Details in this Wiki
• Consumption counters now automatically track servo arm movement and filament cutting for automatic maintenance warnings - no need to add macros yourself. Remember MMU_STATS SHOWCOUNTS=1 to view current counts.
• Now incorporates a filament "tightening" move after loading the toolhead if synced extruder is turned off. This is to prevent false clog detection when the slack in the bowden is greater than the clog detection length
• New variable_user_park_move_macro can be used to customized the movement to the park position instead of default straight line move (Issue #351).
• New printer variables: printer.mmu.gate_filament_name and printer.mmu.spoolman_support
• Fixed issue when the loaded slicer tool map could be reset during print start.
• Several PR's incorporated and bug fixes to address reported Issues.
• Slight changes to stepper synchronization that should help with TTC and stepcompress errors.
• Lots of wiki updates (see links above).
• Tolerance to in Danger Klipper "bleeding edge" added. Comes without warantee!
• Fixed (cosmetic) problem where the load/unload distances in the console animation weren't consistent (Issue #348)
• Added sanity checks to MMU_COLDPULL parameters so it can be called from Mainsail UI (Issue #362)
• Exposed preload_retries parameter to extend the time Happy Hare tries to automatically load a spool once the pre-gate sensor has been triggered (Issue #360)
• Added variable_min_toolchange_z (mmu_macro_vars.cfg) to specify the floor at which any toolchange movement will occur to prevent scraping the bed if no z-hop is specified.
• Project against klipper's new habit of setting toolhead position slightly out of range after homing - save position will ensure it is in range.
• Octoprint compatibity option has been removed from mmu_macro_vars .. not necessary to ensure compatibility anymore
• Wiki page on macro customization has been improved.
• Bloblifier macro update that adds "safe decend logic" to ensure toolhead doesn't hit parts of the print.

v2.7.0 (patches)

• Lots of work to avoid TTC errors. Specifically working around what appears to be a klipper bug when lots of homing moves are used. I know this has solved the problem for the 4 users I was working closely with.
• Improved error reporting for connection problems with SpoolMan.

v2.7.1

Completely revised parking and movement for toolchange operations:

• This is the big one. After upgrade, you MAY NEED TO REVIEW and TWEAK the MOVEMENT section mmu_macro_vars.cfg to finish configuration -- upgrade cannot be completely automated for all setups.
• Previously anything other than simple toolchange workflows was very confusing to setup. The configuration had too many "enable_parking" settings, etc. The new system is both much more sophisticated but should be easier to configure to get the behavior you want. Specifically parking can be defined on 7 operations: toolchange, load, unload, runout, complete, pause & cancel, and for each of those you can choose the parking location,z-hop (including optional ramp) and retraction.
• Additionally movements can be specified between certain toolchange steps to make it easy to, for example, park on a silicon pad to stop ozzing while changing.
• End of print eject will no longer return to the print.
• Rewritten wiki page: Toolchange Movement

Teaser:

variable_enable_park_printing   : 'toolchange,runout,load,unload,complete,pause,cancel'
variable_enable_park_standalone : 'toolchange,load,unload,pause,cancel'
variable_enable_park_disabled   : 'pause,cancel'

variable_min_toolchange_z       : 1.0

variable_park_toolchange        : -1, -1, 1, 10, 2
variable_park_runout            : -1, -1, 2, 10, 2
variable_park_pause             : 50, 50, 10, 0, 2
variable_park_cancel            : 150, 50, 20, 0, 5
variable_park_complete          : 50, 50, 20, 0, 5

variable_pre_unload_position    : -1, -1, 0
variable_post_form_tip_position : -1, -1, 0
variable_pre_load_position      : -1, -1, 0

Automated calibration / tuning of bowden length and gear ratios:

• Gear "ratios" in mmu_vars.cfg have been upgraded to a single list of rotation_distances.
• Bowden tube length can now be automatically tuned over time by setting the auto_calibrate_bowden: 1 parameter. This will use telemetry from successful loads and unloads on gate 0 to adjust slowly to find the perfect length. [Caveat: not tested with all sync-feedback devices like Belay so may be better to initially disable]
• For designs like the ERCF that use a different BMG drive for each gate, each gear needs to be calibrated. Now the option auto_calibrate_gates: 1 will use telemetry similar to above to tune the "rotation_distance" for that gear so movement matches the reference gate 0.

Other:

• Further TTC mitigation. Working with various users I narrowed down the cases where this was most likely to happen and worked around them. Logic is near identical but changes timing enough to prevent the error. But note that TTC can be caused by legitimate causes: PSU, heat, bad cables, overload, etc, etc.
• Fixed error in the amount of filament loaded when using tip cutting (Filametrix). The load length was not correctly being reduced by the toolhead_ooze_reduction value when cutting tip (thanks to user @jacksky007 for debugging)
• Improved error feedback from spoolman moonraker module
• X and Y axis filament cutter support (PR413 - thank you)
• Creality K1 support (PR388 -- thank you)
• Toolerance to skew correct (move out of bounds) in both axes in blobifer macro (PR427 - thank you)
• Various bug fixes from Discord / Issue feedback
• Start of a new wiki page for KlipperScreen-Happy-Hare edition: Klipperscreen
• Wiki pages updated: Slicer Setup, Command Reference, Happy Hare Parameters, Blobbing and Stringing and more..

v2.7.2

Addressed design oversight in toolhead calibration settings when cutting tips

• Fixes issue where toolhead_ooze_reduction parameter was used for two purposes that cancelled each other out and thus prevented use for fine tuning load distance.
  • The previous toolhead_ooze_reduction value will be moved to toolhead_residual_filament to better represent what is means
  • toolhead_ooze_reduction will be reset to 0 and used exclusively for tuning the loading length (it's primary purpose)
  • MMU_CALBRATE_TOOLHEAD updated accordingly
  • Printer variables updated: printer.mmu.extruder_filament_remaining now holds the combined toolhead_residual_filament + any cut fragment length
  • Wiki updated
• New printer variable printer.mmu.toolchange_purge_volume which is valid during a toolchange and contains the recommended purge volume (from slicer tool map purge volues + volume of any residual filament left in extruder). Saves time in macros reading the entire purge volumes map
• Possible TTC mitigations (doing everything possible to give host more headroom)
  • Absolute minimal writes to [save_variables] during toolchange or check gates operations
  • Improved logger
• Allow extruder (entry) sensor to be used to autoload extruder when using the bypass. Controlled with new bypass_autoload parameter in mmu_parameters.cfg
• New rainbow effect on startup on entry LEDs

v2.7.3

** Blobifier v1.5 update. Pretty cool update by @dendrowen incorporating @igiannakas idea of pulsing purging!**

• Purge with a pulsating (and occasionally, retracting) motion. This will prevent laminar flow from occuring and purge the old filament more quickly. (Up to 30% EXTRA filament saved!)
• Changed the blob calculation mode. The blob will now split into equal parts if it is too large (e.g. 2x85mm instead of 150mm + 20mm). This will eliminate/reduce the small blobs scattering over the buildplate.
• Due to the above changes, certain variables have been added and removed:
  • new:
    • z_raise: The total amount the nozzle should be raised during a blob. The value should be somewhere around iteration_z_raise * max_iterations_per_blob - triangular(iteration) * iteration_z_change
    • z_raise_exp: The rate at which the hotend reduces raising speed during a blob. 0.85 seems to be a good starting value.
    • purge_length_maximum: The maximum length of the entire purge. Use max_iterations_per_blob * max_iteration_length.
  • removed: iteration_z_raise, max_iterations_per_blob, iteration_z_change, max_iteration_length
• Revised some parameter checks to work with the new Happy Hare version 2.7
• Add settings:
  • shaker_arm_z to allow for different bed/shaker arm heights.
  • brush_accell to be able to change the acceleration of the brush movement.

---

v3.0.0 (NOT RELEASED YET)

(just so you know what is in the pipeline...)

Major code refactor for modular design

The BIG news: Finally support for Type-B MMU's

• Type-B MMU support (e.g Angry-Beaver, AMS style designs: Box Turtle, others...)
  • New style mmu_hardware.cfg to support replicated configuration. Old configurations will be upgraded but this might be a good time to look at the latest mmu.cfg and mmu_hardware.cfg templates.
  • New individual mmu_post_gate sensor option (e.g. for Amored Turtle)
  • Combined mmu_gate and mmu_extruder (entry) sensors for "no bowden designs" (e.g. Angry Beaver)
  • New per-gate bowden lengths for most Type-B designs
  • Imporved "exit" LED status for Type-B designs without a separate "status" LED.

Other

• New calculated purge volume option using filament colors that is calculted by Happy Hare rather than relying on slicer to supply purge matrix
  • New MMU_CALC_PURGE_VOLUMES command to instruct Happy Hare to calculate purge volumes based on color strategy (slicer or gatemap). This is an option to reading from the slicer.
  • Printer varible printer.mmu.toolchange_purge_volume is always available on toolchange with the purge volume based on chosen strategy.
• Removed persistence_level parameter so that state is now always persisted. There are many command available to reset specifc parts of the state so I decided it was better to always persist. But for QoL, two new startup options have been added:
  • startup_home_if_unloaded can be used to force homing of the selector (if MMU is unloaded) on startup if using a type-A MMU.
  • startup_reset_ttg_map used to reset TTG map to the default on restart.
• Renamed auto_calibrate_gates to autotune_rotation_distance to better describe what it does (auto upgraded)
• Renamed auto_calibrate_bowden to autotune_bowden_length to better describe what it does (auto upgraded)
• New per-filament temperature setting!
  • New (persisted) gatemap "filament temperature" attribute
  • MMU_GATE_MAP command extended with "TEMP=xx" setting per gate
  • When out of a print, logic to ensure correct temperature will be per-filament, falling back to extruder_default_temperature setting if not available
  • Extruder temperature will be pulled from spoolman if spoolman is enabled
• New "addon" for driving DC respooler motor (for example for the Armored Turtle MMU design). Thanks @ammaze!
• Reworked state recovery (MMU_RECOVER) that will utilize all new sensors if available
• Incorporated many PR's. Sorry, I lost count.

This project continues to take considerable effort and time not to mention the cost of building many MMU prototypes. Please consider helping to support me by donating to my PayPal link in the github 🙏