TODO

Scratch pad TODO list

1. DONE - Rewrite automated bowden calibration
2. DONE - Finish homing measurement for non-homing extruder
3. DONE - Pass params to RESUME
4. Compression pin homing feedback for extruder (same as collision)
5. DONE - Record the gate homing point with calibration so dead space can be added/subtracted for quick change
6. DONE - Check that entry_to_extruder amount is added / subtracted too
7. Virtual selector
8. Switching drive gear
9. Virtual servo (force sync KMS case)
10. Prusa_servo mock class .. maybe make servo a separate class for this and #9
11. Inattention time instead of retry on fail. Remove ‘retry_change_on_error’
12. force_form_tip_standalone —> allow_slicer_form_tip or tip forming strategy form|slicer|cut
cut_mmu??
13. _form_tip as separate “_STEP”
14. Externalize ‘boot up tasks’ so users could add things like “check_gates”
15. DONE - Remove sd_card pause..
16. DONE - Disable gate runout during tool change -- maybe code encoder to disable that way too..?
17. DONE - Ensure z_hop is correct if gcode offset is specified. E.g. {% set z_min = params.Z_MIN|default(0)|float %} {% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %}
18. Add 'filament_temp' to gate_map. Also, pull from spoolman. Edit mmu_gate_map command
19. Centralize macro variables .. need to update mmu.my for MMU_TEST_FORM_TIP
20. DONE Deprecate printer.mmu.material .. Replaced with active_gate.material, active_gate.color, ...
21. TODO For advanced calculated purge volumes

Not sure where I'm going with this.  It could be a calculated matrix based on all the referenced tools
assuming they have a pigment percentage (defaulting to 50%). Need to add a PIGMENT=[0-100] param. Or this
could be an orthogonal purge matrix available for filaments on mmu_gate_map. Need to add pigment. Hmmm.
Every update of pigment to gate map would recalc matrix and present as printer variable
        nozzle_volume = gcmd.get_int('NOZZLE_VOLUME', -1, above=0)
        multiplier = gcmd.get_int('MULTIPLIER', 100, above=0)
        algorithm = gcmd.get('ALGORITHM', 'linear')
        algorithms = ['linear', 'quadratic', 'hyperbolic']
        if algorithm not in algorithms:
            raise gcmd.error("ALGORITHM is invalid. Options are: %s" % algorithms]

---

DONE - If EndlessSpool enabled and initial tool is empty, auto map to next gate

DONE - Check comments on tool_tip_macro. Example: variable_cooling_tube_position should have the comment: Measured from Nozzle to Top of Heater Block variable_cooling_tube_length should have the comment: Measured from Top of Heater Block to Top of Heatsink

Reference Markdown

Note

Highlights information that users should take into account, even when skimming.

Tip

Optional information to help a user be more successful.

Important

Crucial information necessary for users to succeed.

Warning

Critical content demanding immediate user attention due to potential risks.

Caution

Negative potential consequences of an action.

stateDiagram-v2
    initialized --> started: <i>(print_start)</i>
    note left of initialized: reset
    standby --> started: <i>(print_start)</i>
    note left of standby: idle_timeout
    ready --> started: <i>(print_start)</i>
    started --> printing
    printing --> complete: (print_complete))
    printing --> error: (print_error)
    printing --> cancelled: CANCEL_PRINT
    printing --> PAUSE: <center><i>mmu error</i><br>or MMU_PAUSE</center>
    state PAUSE {
        direction LR
        pause_locked --> paused: (MMU_UNLOCK)
    }
    PAUSE --> printing: RESUME

Loading

sequenceDiagram
    participant Alice
    participant John
    links Alice: {"Dashboard": "https://dashboard.contoso.com/alice", "Wiki": "https://wiki.contoso.com/alice"}
    links John: {"Dashboard": "https://dashboard.contoso.com/john", "Wiki": "https://wiki.contoso.com/john"}
    Alice->>John: Hello John, how are you?
    John-->>Alice: Great!
    Alice-)John: See you later!

Loading

  flowchart LR;
      A[CI MULTI CHAPTCHA]-->B{Select captcha service by developer?};
      classDef green color:#022e1f,fill:#00f500;
      classDef red color:#022e1f,fill:#f11111;
      classDef white color:#022e1f,fill:#fff;
      classDef black color:#fff,fill:#000;
      B--YES-->C[How to use?]:::green;
      
      C-->U[I choose recaptcha.]:::green;
      U--Views-->Q["echo CIMC_JS('recaptcha');\n echo CIMC_HTML(['captcha_name'=>'recaptcha']);"]:::green;
      U--Controller-->W["CIMC_RULE('recaptcha');"]:::green;
      
      C-->I[I choose arcaptcha.]:::white;
      I--Views-->O["echo CIMC_JS('arcaptcha');\n echo CIMC_HTML(['captcha_name'=>'arcaptcha']);"]:::white;
      I--Controller-->P["CIMC_RULE('arcaptcha');"]:::white;
      
      C-->X[I choose bibot.]:::red;
      X--Views-->V["echo CIMC_JS('bibot');\n echo CIMC_HTML(['captcha_name'=>'bibot']);"]:::red;
      X--Controller-->N["CIMC_RULE('bibot');"]:::red;
      
      B--NO-->D[How to use?]:::black;
      D---Views:::black-->F["echo CIMC_JS('randomcaptcha');\n echo CIMC_HTML(['captcha_name'=>'randomcaptcha']);"]:::black; 
      D---Controller:::black-->T["CIMC_RULE('archaptcha,recaptcha,bibot');"]:::black;

Loading